Duet2 WiFi Firmware on Raise 3d E2 ?

Proschi3D

@Proschi78 said in
this is befor updating

(>>) === Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later<LF>Board ID: 08DLM-996RU-N8PS4-7J1D8-3SJ6N-1B9BR<LF>Used output buffers: 1 of 20 (1 max)<LF>=== RTOS ===<LF>Static ram: 25536<LF>Dynamic ram: 99000 of which 0 recycled<LF>Exception stack ram used: 256<LF>Never used ram: 6280<LF>Tasks: HEAT(blocked,1232) MAIN(running,3828) IDLE(ready,200)<LF>Owned mutexes:<LF>=== Platform ===<LF>Last reset 00:00:40 ago, cause: power up<LF>Last software reset time unknown, reason: User, spinning module GCodes, available RAM 6224 bytes (slot 0)<LF>Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d<LF>Error status: 0<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 20.0MBytes/sec<LF>SD card longest block write time: 0.0ms, max retries 0<LF>MCU temperature: min 18.7, current 23.2, max 23.4<LF>Supply voltage: min 0.0, current 0.6, max 0.9, under voltage events: 0, over voltage events: 0, power good: no<LF>Driver 0: ok, SG[Warning: Maximal number of bytes per line exceeded! Check the EOL (end-of-line) settings or increase the limit in the advanced terminal settings.]

Veti

yes, but my statement was, the firmware was updated to 3.0.

there are config changes you need to do as the rrf2 config does not work with rrf3.

see
https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Summary_of_what_you_need_to_do_to_convert_your_configuration_and_other_files

without those changes you wont be able to move anything.

Proschi3D

I'll keep trying tomorrow, thank you

Proschi3D

the main problem now is that the printer doesn't start anymore.
by start I mean that the display no longer starts up in the menu.
it doesn't finish loading

jay_s_uk

@Proschi78 i guess you need to go back to 2.02 then

Proschi3D

@jay_s_uk that's exactly what I tried.
it just didn't work out.
the board stays at 3.0

Veti

@Proschi78
that might be a price to pay for running the original firmware on the raise 3d

Proschi3D

@Veti but unfortunately he no longer plays the original firmware on the board via the printer

Veti

not sure what you mean

Proschi3D

@Veti https://support.raise3d.com/E2/how-to-update-the-motion-controller-firmware-20-1143.html

The printer does not do the firmware update because the board is flashed to 3.0

Veti

@Proschi78

yes but the firmware updated to 3.0. that is what you wanted to do in the first place.
a lcd screen is not necessary for the operation of a duet.

Proschi3D

@Veti said in Duet2 WiFi Firmware on Raise 3d E2 ?:

yes but the firmware updated to 3.0. that is what you wanted to do in the first place.
a lcd screen is not necessary for the operation of a duet.

in my case it does
the WiFi module sits on the display controller

Veti

@Proschi78 said in Duet2 WiFi Firmware on Raise 3d E2 ?:

in my case it does
the WiFi module sits on the display controller

well you might want to change the eol and line settings in yat so that you can see the actual status of the wifi module.

Proschi3D

i can only connect the motion board via usb.
the display controller is also operated via this interface

Veti

@Proschi78 said in Duet2 WiFi Firmware on Raise 3d E2 ?:

the display controller is also operated via this interface

they can easily just route the spi lines to the display.

that is why the full M122 output is relevant.
you probably did not update the wifi firmware when you updated to the rrf3 firmware.

Proschi3D

@Veti said in Duet2 WiFi Firmware on Raise 3d E2 ?:

they can easily just route the spi lines to the display.
that is why the full M122 output is relevant.
you probably did not update the wifi firmware when you updated to the rrf3 firmware.

I cannot update the WiFi firmware.
because the wifi module is on a different board.
and I have no access to it via the pc

Veti

the wifi firmware is not updated via the pc.

see
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Updating_WiFi_firmware

but the M122 output is important

dc42

@Veti said in Duet2 WiFi Firmware on Raise 3d E2 ?:

@jay_s_uk said in Duet2 WiFi Firmware on Raise 3d E2 ?:

iap4e.bin

did you rename it to Duet2combinesIAP.bin like the error message says?

Duet2CombinedIAP is not the same as iap4e.bin! Renaming it will not work. You can get Duet2CombinedIAP.bin from one of the RRF 3.x releases.

Proschi3D

@dc42 can I go back from V3.0 to V2.02 that easily?

jay_s_uk

@Proschi78 that'll be why the downgrade didn't work then.
use the IAP file dc42 linked to and the firmware from my google drive