if condition RFF3 on GPIO Pin

dc42

I am looking into this, and in the first instance it's a specification issue:

If the tfree file aborts:

Should the whole tool change be cancelled?
What state should RRF assume the machine is in: old tool still loaded, or no tool loaded, or something else?

Similarly if the tpre or tpost file aborts.

RRF does not currently have any concept of a tool change failing.

RS

@dc42: That's certainly useful to look into. I really like the idea of verifying a successful tool lock before moving away and potentially dropping the tool on the bed.

But as I understand it, @sylvain has more issues than an undefined state after the abort. The abort occurs because the microswitch is not recognized as pressed, even though it apparently is, and right now he has no idea why that happens.

Do you think that could also have something to do with the tool change procedure?

Of course, once that's resolved, there's still the specification issue you've mentioned.

duetlover

@RS said in if condition RFF3 on GPIO Pin:

@dc42: That's certainly useful to look into. I really like the idea of verifying a successful tool lock before moving away and potentially dropping the tool on the bed.

But as I understand it, @sylvain has more issues than an undefined state after the abort. The abort occurs because the microswitch is not recognized as pressed, even though it apparently is, and right now he has no idea why that happens.

Do you think that could also have something to do with the tool change procedure?

Of course, once that's resolved, there's still the specification issue you've mentioned.

In fact, at the moment the problem is the random answer of if condition. Sometimes it works, sometimes not...

To be sure this is not a connector issue, I deleted the last connector possible, soldered the wires => same issue !

So, yes, my real problem at the moment is this randoming process.

@dc42 : I'm working on tpost, not tfree

example with tpost :

; tpost0.g
; called after tool 0 has been selected

;heatup
M116 P0

;prime nozzle
;M98 Pprime.g

;mesh levelling on
G29 S1

;PCF fan on
M106 P2 S255


M400
G4 P500

if sensors.gpIn[0].value = 0  ;if the microswitch is not pressed...
	abort "Failed to grab tool 0"
; end if

duetlover

I also tried with if condition at the beginning without success :

; tpost0.g
; called after tool 0 has been selected

M400
G4 P500

if sensors.gpIn[0].value = 0  ;if the microswitch is not pressed...
	abort "Failed to grab tool 0"

;heatup
M116 P0

;prime nozzle
;M98 Pprime.g

;mesh levelling on
G29 S1

;PCF fan on
M106 P2 S255

Same random behaviour

RS

Could you also post your tpre0.g file?

duetlover

Here it is :

; tpre0.g
; called before tool 0 is selected

;Ensure no tool is selected
;T-1

if sensors.gpIn[0].value = 1  ;if the microswitch is pressed...
    abort "Tool 0 still mounted"


;Unlock Coupler
M98 P/macros/Coupler - Unlock

;Move to location
G1 X-10.5 Y200 F50000

;Move in
G1 X-10.5 Y230 F50000

;Collect
G1 X-10.5 Y242.5 F2500

;Close Coupler
M98 P/macros/Coupler - Lock

;WARNING! WARNING! WARNING! WARNING! WARNING! WARNING! WARNING! WARNING! WARNING! WARNING! WARNING! WARNING!
;if you are using non-standard length hotends ensure the bed is lowered enough BEFORE undocking the tool!
G91
G1 Z10 F1000
G90

;Move Out
G1 X-10.5 Y150 F4000

RS

Hm. The whole sequence of movements, plus M400 and G4, looks good to me.

Maybe double and triple check that the microswitch is really pressed correctly every single time? Or check if the cable from the switch to the boards runs close to other cables, where it could pick up noise. No idea how sensitive it would be to noise, but checking it and trying to move it away from other cables can't hurt.

Besides that, I have no more ideas than what I've suggested earlier: try writing a gcode file that simulates the tool change without actually invoking the T command. Just grab the tool, then release it again, in a while loop, and see what happens. In my experience, having a minimal example that reproduces the issue often helps.

dc42

When it fails to detect that the tool has been picked up, if you query the switch position using an echo command or M409, does it report the correct switch state?

duetlover

@dc42 I will echo just before and just after condition test

How should I write it ?
just:

echo sensors.gpIn[0].value

?
Thanks

dc42

Yes, that should work.

duetlover

@dc42 So when it fails the echo command says 0. No problem here

I finally change NO switch to NC one and now it seems to be OK !

Thanks for your help.

jwalker55

@dc42 Is it possible to read a sensor value twice within a single macro? For example, check the state of a switch at the beginning of tpre, then again at the end after the move out? When I do this (just by echoing to console) it outputs the state the switch was in when the macro started (or whenever the sensor was first read in the macro) for both instances despite the switch being pressed at the beginning and unpressed at the end. Aside from that it seems to work as expected if i'm only reading the sensor once.

A Former User

@jwalker55 maybe post your actual files in a new topic? sounds like it should work if the testing is done in the same file as the move is made.

jwalker55

Adding a short (10ms) pause using G4 prior to the second sensor reading seemed to fix it.

dc42

Alternatively you could have added M400 after the movement commands and before reading the switch again, so that the macro waited until the movement completed.

jwalker55

@dc42 I'm an idiot. You literally said that above and I somehow read past it. My apologies.