Software bundle 3.1.1 now available

deckingman

Sorry if I'm being thick but I'm still on a very early beta (pre - RC) firmware and it has been many months since I last installed an update. I'm not sure what the RepRap firmware zip file contains - maybe I missed something somewhere.

I've made the following assumptions which I'd like to be confirmed please. Note, I'm still running stand alone - non RPi

The "Duet2and3Firmware-3.1.0.zip is just the firmware. I still need to separately download and instal "DuetwebControl 3.1.0." Yes or no?
The "Duet2and3Firmware-3.1.0.zip" is just for the main board. I still need to separately download and instal "Duet3Firmware_EXP3HC.bin" for the expansion boards. Yes or no?

Also, what is the procedure for updating expansion board firmware these days? Do I still need to send M997 Bn after uploading it or just run M98 P"config.g"?

Thanks

Phaedrux

@deckingman said in Software bundle 3.1.0 now available:

Duet2and3Firmware-3.1.0.zip

Looks like the zip file contains everything needed for the board firmware, expansion tool board firmwares and the DWC files.

I don't know what version you're running specifically, but it may be best to update to 3.0 with it's zip file, and then 3.01 with it's zip file

deckingman

@Phaedrux said in Software bundle 3.1.0 now available:

Looks like the zip file contains everything needed for the board firmware, expansion tool board firmwares and the DWC files.

I don't know what version you're running specifically, but it may be best to update to 3.0 with it's zip file, and then 3.01 with it's zip file

ref Zip file - Cool.
ref 3.0 - Good point. I'd have to check but methinks it'll be something like MB6HC291919 for the main board and EXPHC28b4 for the expansion boards. I guess it'll do no harm to update to 3.0 first in any case.

Do you happen to know if it's still necessary to send M997 Bn after uploading expansion board firmware?

dc42

@deckingman said in Software bundle 3.1.0 now available:

Do you happen to know if it's still necessary to send M997 Bn after uploading expansion board firmware?

It should install it automatically. Use M115 B# (# = CAN address of each expansion board) to check that it worked.

Danal

@dc42 said in Software bundle 3.1.0 now available:

@deckingman said in Software bundle 3.1.0 now available:

Do you happen to know if it's still necessary to send M997 Bn after uploading expansion board firmware?

It should install it automatically. Use M115 B# (# = CAN address of each expansion board) to check that it worked.

Well... then... report:

In a Pi + 6HC + 2 x 3HC + 1HC system, the 6HC was firmware upgraded during the "sudo apt upgrade". The expansions and tool were not. I M997 each manually, and that went fine.

sudo journalctl -u duetcontrolserver (snipped to startup of 3.1 server)

May 15 13:29:36 duet3 systemd[1]: Started Duet Control Server.
May 15 13:29:36 duet3 DuetControlServer[3530]: Duet Control Server v3.1.0
May 15 13:29:36 duet3 DuetControlServer[3530]: Written by Christian Hammacher for Duet3D
May 15 13:29:36 duet3 DuetControlServer[3530]: Licensed under the terms of the GNU Public License Version 3
May 15 13:29:36 duet3 DuetControlServer[3530]: [info] Settings loaded
May 15 13:29:37 duet3 DuetControlServer[3530]: [info] Environment initialized
May 15 13:29:37 duet3 DuetControlServer[3530]: [info] Connection to Duet established
May 15 13:29:37 duet3 DuetControlServer[3530]: [info] IPC socket created at /var/run/dsf/dcs.sock
May 15 13:29:37 duet3 systemd[1]: /lib/systemd/system/duetcontrolserver.service:9: CPU scheduling priority is out of range, ignoring: 20
May 15 13:29:39 duet3 systemd[1]: /lib/systemd/system/duetcontrolserver.service:9: CPU scheduling priority is out of range, ignoring: 20
May 15 13:29:40 duet3 systemd[1]: /lib/systemd/system/duetcontrolserver.service:9: CPU scheduling priority is out of range, ignoring: 20
May 15 13:29:44 duet3 DuetControlServer[3530]: [info] Flashing IAP binary
May 15 13:29:44 duet3 DuetControlServer[3530]: [info] Flashing RepRapFirmware
May 15 13:29:51 duet3 DuetControlServer[3530]: [info] Verifying checksum
May 15 13:29:54 duet3 DuetControlServer[3530]: [info] Firmware update successful
May 15 13:29:54 duet3 DuetControlServer[3530]: [info] Starting macro file config.g on channel Trigger
May 15 13:29:54 duet3 DuetControlServer[3530]: [info] FTP is enabled on port 21
May 15 13:29:54 duet3 DuetControlServer[3530]: [info] TELNET is enabled on port 23
May 15 13:29:55 duet3 DuetControlServer[3530]: [info] Starting macro file yLimitPark.g on channel Trigger
May 15 13:29:55 duet3 DuetControlServer[3530]: [info] Finished macro file yLimitPark.g
May 15 13:29:55 duet3 DuetControlServer[3530]: [warn] M307: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
May 15 13:29:55 duet3 DuetControlServer[3530]: [info] Starting macro file /sys/Toffsets.g on channel Trigger
May 15 13:29:56 duet3 DuetControlServer[3530]: [info] Finished macro file /sys/Toffsets.g
May 15 13:29:56 duet3 DuetControlServer[3530]: [info] Finished macro file config.g
pi@duet3:~ $

chrishamm

@Danal We decided to upgrade only the main firmware via the 3.1.0 package but that may change in 3.2.0. You do have to run M997 B>=1 in SBC mode to update the expansion boards.

deckingman

@Phaedrux said in Software bundle 3.1.0 now available:

Looks like the zip file contains everything needed for the board firmware, expansion tool board firmwares and the DWC files.

I don't know what version you're running specifically, but it may be best to update to 3.0 with it's zip file, and then 3.01 with it's zip file

Sorry - I'm still big thick. I've downloaded both RRF 3.0 and 3.1 zip files and extracted the contents into separate folders. I'm not seeing any DWC files that you indicated would be included, so I guess I still need to download the DWC zip separately yes? Or have I done something wrong?

Also, I see "DuetFirmware_TOOL1LC.bin" which I'm guessing is for tool boards. So as I only have expansion boards, I don't need that yes?

Finally, I see "Duet3_SDiap_MB6HC.bin. I think I already have that but I'm guessing this might be a later version so I ought to instal it yes?

Cheers

A Former User

@deckingman said in Software bundle 3.1.0 now available:

I've downloaded both RRF 3.0 and 3.1 zip files and extracted the contents into separate folders

upload straight to dwc, no extraction first?

deckingman

@bearer said in Software bundle 3.1.0 now available:

@deckingman said in Software bundle 3.1.0 now available:

I've downloaded both RRF 3.0 and 3.1 zip files and extracted the contents into separate folders

upload straight to dwc, no extraction first?

Oh really? Cool

Edit - things have moved on since December

A Former User

@deckingman might be a feature of dwc2, however from my point of view its always been like that even in RRF2. Then again I'm (relatively) new to the game

deckingman

@bearer said in Software bundle 3.1.0 now available:

@deckingman might be a feature of dwc2, however from my point of view its always been like that even in RRF2. Then again I'm (relatively) new to the game

Yes DWC has been updated by installing from a zip file for a very long time. But last time I updated the main board and expansion boards firmware back in December it was still done by uploading the individual firmware files. So updating everything, including all the boards firmwares as well as DWC from a single zip is new to me.

arhi

@deckingman said in Software bundle 3.1.0 now available:

So updating everything, including all the boards firmwares as well as DWC from a single zip is new to me.

Didn't know it can be done like that?

I always upload the two bin's and the DWC ask if I want to flash the updated firmware file. The "big" zip file has too much stuff, never tried uploading that one

dc42

So far we are investigating two bug reports for the 3.1.0 release:

One user has reported that he is getting occasional resets. The M122 report shows the reason is stack overflow from the Network task (NETW in the M122 report). If you encounter this issue, please see this thread https://forum.duet3d.com/topic/16390/3-1-0-firmware-reboots-periodically for what to do.
Duet 3 with attached SBC fails to write the height map file after running G29. We are investigating this. Further information will be posted in this thread https://forum.duet3d.com/topic/16388/g29-not-writing-a-heightmap-csv.

deckingman

@arhi Glad I'm not the only one who didn't know that (but I haven't tried it yet).

deckingman

@dc42 Ahhh. Well in that case I'll hold off updating for now....

Danal

@chrishamm said in Software bundle 3.1.0 now available:

@Danal We decided to upgrade only the main firmware via the 3.1.0 package but that may change in 3.2.0. You do have to run M997 B>=1 in SBC mode to update the expansion boards.

Thanks. That's actually what I thought... I just read something into a post that wasn't there.

CCS86

This post is deleted!

Macwolf

the update to 3.10 worked well, unfortunately my PanelDue 7 "no longer wants to connect to my duet2maestro
there are already solutions for this Problem?
thank you

A Former User

@Macwolf said in Software bundle 3.1.0 now available:

PanelDue 7 "no longer wants to connect to my duet2maestro

https://github.com/Duet3D/RepRapFirmware/blob/v3-dev/WHATS_NEW_RRF3.md#reprapfirmware-310

arhi

8.5h print - done, flawless (few small ones done before it)

5/16/2020, 8:30:07 PM 	M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.0 running on Duet Ethernet 1.02 or later
Board ID: 08DGM-9T6BU-FG3S4-6J9FD-3SD6Q-KVRBF
Used output buffers: 3 of 24 (14 max)
=== RTOS ===
Static ram: 28180
Dynamic ram: 93784 of which 32 recycled
Exception stack ram used: 568
Never used ram: 8508
Tasks: NETWORK(ready,76) HEAT(blocked,1168) MAIN(running,1880) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 21:14:17 ago, cause: power up
Last software reset at 2020-05-15 22:30, reason: User, spinning module GCodes, available RAM 9356 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 10
MCU temperature: min 28.5, current 35.4, max 37.0
Supply voltage: min 23.0, current 24.0, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/367
Driver 1: ok, SG min/max 0/411
Driver 2: standstill, SG min/max 0/435
Driver 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2020-05-16 20:30:07
Cache data hit count 4294967295
Slowest loop: 604.84ms; fastest: 0.13ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 5.3ms, write time 617.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 157, MinFreeDm: 104, MaxWait: 44825051ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 1381801, completed moves: 1381761, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.8
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 E0.1000 F3000" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 617.56ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex
=== Filament sensors ===
Extruder 0 sensor: no data received
5/16/2020, 9:12:44 PM 	Finished printing file 0:/gcodes/Body_high_detail.gcode, print time was 8h 28m
5/17/2020, 1:10:04 AM 	M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.0 running on Duet Ethernet 1.02 or later
Board ID: 08DGM-9T6BU-FG3S4-6J9FD-3SD6Q-KVRBF
Used output buffers: 1 of 24 (19 max)
=== RTOS ===
Static ram: 28180
Dynamic ram: 93784 of which 32 recycled
Exception stack ram used: 568
Never used ram: 8508
Tasks: NETWORK(ready,76) HEAT(blocked,1168) MAIN(running,1880) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 25:54:14 ago, cause: power up
Last software reset at 2020-05-15 22:30, reason: User, spinning module GCodes, available RAM 9356 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 10
MCU temperature: min 31.6, current 35.1, max 35.7
Supply voltage: min 23.4, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/315
Driver 1: standstill, SG min/max 0/383
Driver 2: standstill, SG min/max 0/405
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2020-05-17 01:10:04
Cache data hit count 4294967295
Slowest loop: 79.29ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 2.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 109, MaxWait: 14ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 1498329, completed moves: 1498329, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.7
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 7.02ms; fastest: 0.06ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex
=== Filament sensors ===
Extruder 0 sensor: no data received