Gcode upload failes
-
I printed something last night and wanted to start a new print this morning.
But I am unable to upload the Gcode.=== Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later Board ID: 08DJM-9178L-L4MSN-6J9F2-3S86P-T902N Used output buffers: 3 of 24 (9 max) === RTOS === Static ram: 30516 Dynamic ram: 91836 of which 0 recycled Exception stack ram used: 224 Never used ram: 8496 Tasks: NETWORK(ready,728) HEAT(blocked,1240) MAIN(running,3676) IDLE(ready,156) Owned mutexes: === Platform === Last reset 00:02:30 ago, cause: software Last software reset at 2020-03-01 07:58, reason: User, spinning module GCodes, available RAM 8208 bytes (slot 2) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 6.7ms, max retries 0 MCU temperature: min 36.9, current 37.5, max 37.9 Supply voltage: min 23.9, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max not available Driver 1: standstill, SG min/max not available Driver 2: standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: standstill, SG min/max not available Date/time: 2020-03-01 08:01:43 Cache data hit count 410603317 Slowest loop: 7.43ms; fastest: 0.09ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms Bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === AuxDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Stack records: 2 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 16.33ms; fastest: 0.00ms Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address 84:0d:8e:b3:b0:3a WiFi Vcc 3.39, reset reason Turned on by main processor WiFi flash size 4194304, free heap 24288 WiFi IP address 192.168.178.47 WiFi signal strength -69dBm, reconnections 0, sleep mode modem Socket states: 0 2 0 0 0 0 0 0 -
What happens when you try to upload the GCode file?
-
it first shows 26%, sometimes it directly goes to error and the other times it moves really slowly up and that moment it would go to 100% it shows error.
Tried to upload 8 times and the ninth it uploaded successfully. -
After the first success I didn't had another error.
-
@X30N said in Gcode upload failes:
WiFi signal strength -69dBm
Your WiFi signal strength is a little low. If you experience further errors, see https://duet3d.dozuki.com/Wiki/WiFi_disconnections_and_AJAX_timeout_errors.
