RepRapFirmware 3.0 is released!

[bulka]

@blt3dp

tried with M558 P5 R0.4 C"zprobe.in+zprobe.mod" H1 F120 T6000 but nothing changed

[Dougal1957]

@bulka is this a Duet Wifi or Duet3? and Am I right in thinking it is a smart effector?

[bulka]

@Dougal1957

I'm using this https://www.duet3d.com/DeltaSmartEffector

[Dougal1957]

@bulka ok here is my config file using the same hardware.

; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Fri Jul 07 2017 14:49:07 GMT+0100 (BST)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 L450.570 R239.241 H400.083 B175.0 X0.081 Y0.091 Z0.000    ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0.315 Y0.808 Z-1.123 A0.20 B0.02                         ; Put your endstop adjustments here, or let auto calibration find them 

;M665 L450.570 R239.403 H400.898 B175.0 X0.191 Y0.213 Z0.000  ; Set delta radius, diagonal rod length, printable radius and homed height
;M666 X0.392 Y0.645 Z-1.037 A0.12 B-0.07  ; Put your endstop adjustments here, or let auto calibration find them
M208 Z0 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; Define active high microswitches
M558 P5 C"^zprobe.in" X0 Y0 Z0 H5 R0.4 F1200 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
G31  P100 X0 Y0 Z-0.05; Set Z probe trigger value, offset and trigger height
M557 R160 S20 ; Define mesh grid

; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M92 X200 Y200 Z200 E1667 ; Set steps per mm
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M566 X900 Y900 Z900 E40 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E2400 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E120 ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E500 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M143 S300 ; Set maximum heater temperature to 300C
;M305 P0 X201 ; Set thermistor + ADC parameters for heater 0 and remap it to channel 201
;M305 P1 X200 ; Set thermistor + ADC parameters for heater 1 and remap it to channel 200
M308 S0 P"spi.cs2" Y"rtd-max31865" F50
M308 S1 P"spi.cs1" Y"rtd-max31865" F50
M950 H0 C"bed_heat" T0
M950 H1 C"e0_heat" T1
;M307 H0 A199.0 C962.6 D5 B0
;M307 H1 A409.7 C232.2 D4.5 B0
;M307 H0 A161.6 C1109.8 D5.8 S1.00 V24.4 B0
M307 H0 A449.1 C783.3 D9.8 S1.00 V24.4 B0
M307 H1 A544.9 C280.1 D4.2 S1.00 V24.4 B0

; Tools
M563 P0 D0 H1 F2; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Network
M550 PDelta ; Set machine name
M552 S1 ; Enable network
; Access point is configured manually via M587 by the user
M586 P0 S1 ; Enable HTTP
M586 P1 S1 ; Enable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
;M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
;M106 P2 S1 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off
M563 P0 D0 H1
M564 H0
; Custom settings are not configured
T0
G28
;G29 S1
;M572 D0 S0.05    ; set pressure advance
M501

This works I am on RRF 3.0 on my Wifi board

Hopefully this will help you

note the probe settings for the smart effector

M558 P5 C"^zprobe.in" X0 Y0 Z0 H5 R0.4 F1200 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
G31 P100 X0 Y0 Z-0.05; Set Z probe trigger value, offset and trigger height

[deckingman]

@DaBit I'll check my settings when I get back home in 8 days or so. I suspect that I'm using 10Hz because that is what I've always used. IIRC that figure of 10Hz was chosen specifically to suit SSRs. However, do not confuse the PWM frequency with the mark-space ratio that is PWM itself. And also, don't forget that the thermal mass of the aluminium plate acts as a huge damper to the conduction of heat through the plate, which makes the PWM frequency largely irrelevant.

[blt3dp]

@bulka

You have a bed.g file?

[bulka]

@blt3dp
yes

@Dougal1957

thank you, now it's working , ^zprobe.in was the right choice.

[Dougal1957]

@bulka Glad to be of help

Doug

[garyd9]

The documentation for converting M558 to RRF3 is a bit confusing in regards to the "I" parameter. In particular, it doesn't say anything about it (in that section)

https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_M558

As well, the gcode wiki page also seems to imply that "M558 I1" is valid (https://duet3d.dozuki.com/Wiki/Gcode#Section_M558_Set_Z_probe_type)

"All of the above for RepRapFirmware 2.x relates to RepRapFirmware 3, except the following:" (and nothing that follows makes mention of the I param.)

Yet, from reading this thread, I get the impression that RRF2:
M558 P8 I1 R0.4 F300 H3

does not work in RRF3 as:
M558 P8 R0.4 I1 C"zprobe.in" H3 F300

and instead should be written as:
M558 P8 R0.4 C"!zprobe.in" H3 F300 ; I1 removed, ! prepended to zprobe.in

---

Edit: I accidentally left the "I1" in my 558 after converting, and had the ! before the pin. The result apparently was a double inversion. Removing the I1 and leaving the "!" made everything seem to work.

So ... which is the proper way?

[garyd9]

Duet2 wifi h/w version 1.04
Printer is a normal delta (with 0.9 degree steppers)
Firmware is the first general release of RRF3

After starting my first print with RRF3 on a Duet2 WiFi, I'm seeing a LOT of hiccups using an identical configuration to what I used with RRF2 (where I only rarely saw a hiccup.)

For example, 45 seconds after sending "M122", I sent M122 again and saw "Hiccups: 423(0)"

Measuring it at one point, I got 161 hiccups for a travel move of around 80mm.

The hiccups seem to be only after travel moves which are configured at 200mm/sec in my slicer. Yes, I could slow this down and probably get rid of the hiccups, but the point is that I did NOT get hiccups with RRF2.0.5 with the exact same gcode file.

The speed related lines in my config.g are directly copied from my RRF2 config.g, as well as the stepper config. I've included them below:

M350 X16 Y16 Z16 E16 I1                                ; configure microstepping with interpolation
M92 X199.50 Y199.50 Z199.50 E837.50                    ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E2400.00               ; set maximum instantaneous speed changes (mm/min)
M203 X21000.00 Y21000.00 Z21000.00 E10000            ; set maximum speeds (mm/min) (severely limited by slicer)
M201 X1500.00 Y1500.00 Z1500.00 E1000.00               ; set accelerations (mm/s^2) (limited by M204)
M204 P500 T1200

The delta parameters are:

M665 L360.260:360.260:360.250 R215.476 H415.377 B140.0 X0.426 Y0.176 Z0.000
M666 X0.298 Y-0.635 Z0.337 A-0.31 B0.33

A random M122 is also shown in case there's some information that might diagnose an issue:

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later
Board ID: 08DGM-9T6BU-FG3SN-6JKD6-3S46P-KUYVD
Used output buffers: 3 of 24 (23 max)
=== RTOS ===
Static ram: 30516
Dynamic ram: 91248 of which 96 recycled
Exception stack ram used: 544
Never used ram: 8668
Tasks: NETWORK(ready,640) HEAT(blocked,1240) MAIN(running,104) IDLE(ready,156)
Owned mutexes:
=== Platform ===
Last reset 01:32:22 ago, cause: software
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 8940 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 14.1ms, max retries 0
MCU temperature: min 36.0, current 36.6, max 37.0
Supply voltage: min 23.3, current 23.5, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/990
Driver 1: ok, SG min/max 0/267
Driver 2: ok, SG min/max 0/403
Driver 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2020-01-09 22:39:36
Cache data hit count 4294967295
Slowest loop: 13.92ms; fastest: 0.10ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 621(0), FreeDm: 153, MinFreeDm: 101, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 119268, completed moves: 119228, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 1
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X-14.161 Y69.007 E0.00898" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 200.45ms; fastest: 0.09ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(1)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 23
WiFi firmware version 1.23
WiFi MAC address 84:f3:eb:83:42:fc
WiFi Vcc 3.41, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24224
WiFi IP address 192.168.7.10
WiFi signal strength -50dBm, reconnections 0, sleep mode modem
Socket states: 2 0 0 0 0 0 0 0

[appjaws]

I am totally confused ( not hard to do)

I have a part fan connected to board Fan0
I have an extruder fan connected to board Fan1
I have a system fan connected to board Fan2

I have made changes to the config file for RRF3 but the fans are not working properly, the extruder fan is on all the time, the system fan is not working and the part fan comes on if I move the sliders on part or system.
Very frustrating.

RepRapFirmware 2 settings
; Thermistors and heaters
M305 P0 R4700 B3950 S"Bed Heater" ; bed thermistor R and B values
M305 P1 R4700 B4388 H23 S"Hot end" ; nozzle 1 thermistor R and B values
M307 H0 A104.6 C986.0 D1.9 ;B0 ; Auto tune PID for bed heater
M307 H1 A669.8 C253.0 D4.5 ;B0 ; Auto tune PID for extruder 0
; Fan settings
M106 P1 T45 H1 ; Fan 1 to run when H1 is above 45Celsius
M106 P2 H100:101 T35:50 L0.3 ; electronics cooling fan

all of the above works correctly.

RepRapFirmware 2 settings
; Thermistors and heaters
M950 H0 C"bed_heat" T0 ; create bed heater output on bedheat and map it to sensor 0
M308 S0 P"bed_temp" Y"thermistor" T4700 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M143 H0 S70 ; set temperature limit for heater 0 to 70C
M307 H0 A104.6 C986.0 D1.9 B0 S1.00 ; Auto tune PID for bed heater

M950 H1 C"e0_heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M308 S1 P"e0_temp" Y"thermistor" T4700 B4388 ; configure sensor 1 as thermistor on pin e0temp
M143 H1 S230 ; set temperature limit for heater 1 to 230C
M307 H1 A669.8 C253.0 D4.5 B0 S1.00 ; Auto tune PID for extruder 0

M308 S100 Y"mcu-temp" A"CPU" ; CPU temp sensor
M308 S101 Y"drivers" A"Duet_drv" ; drivers temp sensor

; Fan settings
M950 F0 C"fan0" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P0 C"PartFan" ; set Part fan.
M950 F1 C"fan1" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P1 S0 H1 T45 C"Extruder" ; set Extruder Fan. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P2 H100:101 T35:55 L40 C"System" ; set System fan. Thermostatic electronics cooling fan

[matej1006]

Hello @dc42
why i get G28 error when i want to home my locking actuator?

; Home U Axis
G91                     ; Set relative mode
G1 U-360 F9000 H1       ; Big negative move to search for home endstop
G1 U4 F600              ; Back off the endstop
G1 U-10 F600 H1       ; Find endstop again slowly
G90                     ; Set absolute mode

Here is code from homeu.g

and here is from homeall.g

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2.0.4 on Sat Oct 12 2019 15:44:24 GMT+0200 (Srednjeevropski poletni čas)

T-1 			;remove tool befor probing
G91                     ; relative positioning
G1 Z5 F3000 H2          ; lift Z relative to current position
G1 H1 X-435 Y-388 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-435             ; home X axis
G1 H1 Y-388           	; home Y axis
G1 X5 Y5 F3000         	; go back a few mm
G1 H1 X-435 F360        ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-388            	; then move slowly to Y axis endstop
G90                     ; absolute positioning
G1 X210 Y200 F3000      ; go to first bed probe point and home Z
G30                     ; home Z by probing the bed
M98 P"homeu.g"
; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 H2 Z5 F50           ; lift Z relative to current position
;G90                    ; absolute positioning

Matej

[dc42]

@matej1006 said in RepRapFirmware 3.0 is released!:

Hello @dc42
why i get G28 error when i want to home my locking actuator?

What is the error message?

[matej1006]

@dc42 G28 Failed to enable edstops

[dc42]

@appjaws said in RepRapFirmware 3.0 is released!:

I have made changes to the config file for RRF3 but the fans are not working properly, the extruder fan is on all the time, the system fan is not working and the part fan comes on if I move the sliders on part or system.

If you run M98 P"config.g", do you get any error messages?

Some problems I can see:

• The M308 command to create a sensor should come before the M950 command that uses it (twice in your config.g)
• Your M308 commands include T4700, which means you have 4.7K thermistors. Remove that parameter
• Max sensor number is 63, so you can't use sensor numbers 100 and 101

[matej1006]

@dc42 said in RepRapFirmware 3.0 is released!:

M98 P"config.g"

if i send M98 P"config.g" there is no error

[dc42]

@matej1006 said in RepRapFirmware 3.0 is released!:

@dc42 G28 Failed to enable edstops

Sounds like a problem with M574 commands. Please post your config.g file.

[matej1006]

@dc42
and why i can't see in extra temperature for water

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.0.4 on Sat Oct 12 2019 15:44:24 GMT+0200 (Srednjeevropski poletni čas)

; General preferences
G90                                     ; send absolute coordinates...
M83                                     ; ...but relative extruder moves

M80					; force the PS_ON line to 0V/GND; causing a voltage over relay, thus enabling it. 
					; With the relay active, it close the circuit of the Live wire, taking over to supply the Power Supply.
 
M550 P"Toolchange printer"              ; set printer name

M667 S1                                 ; select CoreXY mode

; Network
M552 S0
M552 S1                                 ; enable network
M586 P0 S1                              ; enable HTTP
M586 P1 S0                              ; disable FTP
M586 P2 S0                              ; disable Telnet

; Debugging
M111 S0                                 ; Debug off
M929 P"eventlog.txt" S1                 ; Start logging to file eventlog.txt

; Drives

;X and Y motors
M569 P5 S0                              ; Drive 5 direction | Y Stepper
M569 P6 S0				; Drive 6 direction | Y Stepper

;Z motors
M569 P7 S0                              ; Drive 7 direction | Front Right Z
M569 P8 S0                              ; Drive 8 direction | Back Z
M569 P9 S0                              ; Drive 9 direction | Front Left Z

;Extruders
M569 P1 S0                              ; Drive 1 direction | Extruder0
M569 P2 S0                              ; Drive 2 direction | Extruder1
M569 P3 S0                              ; Drive 3 direction | Extruder2
M569 P4 S0                              ; Drive 4 direction | Extruder3


; Toolchanger actuator
M569 P0 S1					; Drive 0 direction | Toolchanger Actuator

M584 X6 Y5 Z9:8:7 U0 E1:2:3:4                   ; set drive mapping
M671 X-28:172:458 Y146:402:146 S15 		; leadscrews at front left, rear middle and front right

M350 X16 Y16 Z16 E16 U4 I1                 	; configure microstepping with interpolation
M92  X80.00 Y80.00 Z400.00 E420.00 U20   	; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 U750    	; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z1500.00 E1200.00 U10000 ; set maximum speeds (mm/min)
M201 X800 Y800 Z20 E1000 U1500          	; set accelerations (mm/s^2)
M906 X900 Y900 Z900 E800 U1000 I60            	; set motor currents (mA) and motor idle factor in per cent

; Axis Limits
M208 X0 Y0 Z0 S1                        	; set axis minima
M208 X420 Y380 Z480 S0                  	; set axis maxima

; Endstops
M574 U1 S1                           		; Set homing switch configuration for toolchange lock. Both switches should be wired NC and in series.
M574 X1 Y1 S1                           	; set active low and disabled endstops

; Z-Probe
M574 Z1 S2 					; Set endstops controlled by probe
M558 P1 C"zprobe.in+zprobe.mod" H5 F120 T3000   ; Set Z probe type to modulated and the dive height + speeds
G31 P467 X0 Y40 Z1.0 				; Set Z probe trigger value, offset and trigger height

; Heaters
; Bed Heater
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138                  			; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                                                                   ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120                                                                            ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00                                                                        ; disable bang-bang mode for the nozzle heater and set PWM limit

; Tool1 Heater
;M308 S1 P"spi.cs1" Y"rtd-max31865"                                                     ; configure sensor 1 as thermocouple via CS pin spi.cs1
M308 S1 P"duex.e2temp" Y"thermistor" T100000 B4138                                      ; configure sensor 1 as thermistor on pin duex.e2temp
M950 H1 C"duex.e2heat" T1                                                               ; create nozzle heater output on duex.e2heat and map it to sensor 1
M143 H1 S280                                                                            ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00                                                                        ; disable bang-bang mode for the nozzle heater and set PWM limit

; Tool2 Heater
;M308 S2 P"spi.cs2" Y"rtd-max31865"                                                     ; configure sensor 2 as thermocouple via CS pin spi.cs2
M308 S2 P"duex.e3temp" Y"thermistor" T100000 B4138                                      ; configure sensor 2 as thermistor on pin duex.e3temp
M950 H2 C"duex.e3heat" T2                                                               ; create nozzle heater output on duex.e3heat and map it to sensor 2
M143 H2 S280                                                                            ; set temperature limit for heater 2 to 280C                                               
M307 H2 B0 S1.00                                                                        ; disable bang-bang mode for the nozzle heater and set PWM limit

; Tool3 Heater
;M308 S3 P"spi.cs3" Y"rtd-max31865"                                                     ; configure sensor 3 as thermocouple via CS pin spi.cs3
M308 S3 P"duex.e4temp" Y"thermistor" T100000 B4138                                      ; configure sensor 3 as thermistor on pin duex.e4temp
M950 H3 C"duex.e4heat" T3                                                               ; create nozzle heater output on duex.e4heat and map it to sensor 3
M143 H3 S280                                                                            ; set temperature limit for heater 3 to 280C                                               
M307 H3 B0 S1.00                                                                        ; disable bang-bang mode for the nozzle heater and set PWM limit

; Tool4 Heater
;M308 S4 P"spi.cs4" Y"rtd-max31865"                                                     ; configure sensor 4 as thermocouple via CS pin spi.cs4
M308 S4 P"duex.e5temp" Y"thermistor" T100000 B4138                                      ; configure sensor 4 as thermistor on pin duex.e5temp
M950 H4 C"duex.e5heat" T4                                                               ; create nozzle heater output on duex.e5heat and map it to sensor 4
M143 H4 S280                                                                            ; set temperature limit for heater 4 to 280C
M307 H4 B0 S1.00 									; disable bang-bang mode for the nozzle heater and set PWM limit
 
                                                                                                   
; Tool definitions
M563 P0 S"TOOL1" D0 H1 F3  					; Define tool 1
G10 P0 Z-3.75                   				; Set tool 1 offset from the bed
G10 P0 R170 S190                				; Set tool 1 operating and standby temperatures(-273 = "off")
;M572 D0 S0.1				    			; Set pressure advance on Extruder Drive 0

M563 P1 S"TOOL2" D1 H2 F4  					; Define tool 2
G10 P1 Z-3.75         						; Set tool 2 offset from the bed with tool-0 as a reference.
G10 P1 R170 S190                				; Set tool 2 operating and standby temperatures(-273 = "off") 
;M572 D1 S0.1				    			; Set pressure advance on Extruder Drive 1,

M563 P2 S"TOOL3" D2 H3 F5  					; Define tool 3
G10 P2 Z-3.75                   				; Set tool 3 offset from the bed
G10 P2 R170 S190         				; Set tool 3 operating and standby temperatures(-273 = "off")
;M572 D2 S0.1				    			; Set pressure advance on Extruder Drive 2

M563 P3 S"TOOL 4" D3 H4 F6   					; Define tool 4
G10 P0 Z-3.75                    				; Set tool 4 offset from the bed
G10 P0 R170 S190		 				; Set tool 4 operating and standby temperatures(-273 = "off")
;M572 D3 S0.1				    			; Set pressure advance on Extruder Drive 3

;Water temp
M308 S5 P"e1temp" Y"thermistor" T100000 B4138                   ;configure sensor 5 as thermistor on pin e1temp
                             						; disable bang-bang mode for the nozzle heater and set PWM limit             
                                                          
; Fans
M950 F0 C"!Fan0+exp.pb6" Q25000 				; fan 0 is a 4-wire PWM fan so invert it, use high PWM frequency, tacho connected to PB6 on expansion connector
M106 H0 S1 T25                                                  ; set fan 0 value. Thermostatic control is turned on

; Custom settings are not defined

; Miscellaneous
T-1                                      			; select first tool

[matej1006]

@dc42 i figurit out for homing u axe i stiil have problem with showing temp on graph and extra temp for water and MCU temp

[wilriker]

@matej1006 If a sensor is not bound to a heater it needs to be given a name to show up in the UI. That's done with the A parameter for M308.