Strange failure rate of fans
-
cheap fans, like almost everything else, are cheap for a reason...
-
I did once cave and buy a 3 pack of blower fans from amazon for 5$ free shipping. The first fan I hooked up had a loud pop sound and an awful awful smell. It released the blue smoke. I took it off and peeled back the sticker. And underneath I saw that the black wire was connected to the terminal screen printed with a plus sign and the red wire was connected to the terminal screen printed with the minus sign. I figured out why they were so cheap. I checked the other fans, same thing. I wired another one up again, this time with wires reversed, and it worked. It was loud, but it worked. I immediately went to digi-key and ordered a sunon blower. Luckily it didn't kill the board.
-
I suggest buying some Sunon fans, they even have some 5015 blower fan like MF50151VX-A99, they are not the quiets but super powerful. If it it is too loud you can easily run it at lower PWM and they still will coll even PLA fine.
-
Thanks to everyone for their comments, so, and let me take a moment to reflect here, but yes, you are all accusing me of being a cheapskate
I can't use Noctua as they don't do 24V 40mm axial or 40mm
blower and Sunon don't do any small blowers.Any other suggestions?
Here's the one I have at the moment
dc42: you say 500Hz may be a bit fast. what would be the standard setting?
Thanks
-
@pcsentinel said in Strange failure rate of fans:
dc42: you say 500Hz may be a bit fast. what would be the standard setting?
The blower fans I have tried don't like PWM at all. They sort of work at very low PWM frequencies e.g. 10Hz.
-
@pcsentinel said in Strange failure rate of fans:
Thanks to everyone for their comments, so, and let me take a moment to reflect here, but yes, you are all accusing me of being a cheapskate
I can't use Noctua as they don't do 24V 40mm axial or 40mm
blower and Sunon don't do any small blowers.Any other suggestions?
Here's the one I have at the moment
dc42: you say 500Hz may be a bit fast. what would be the standard setting?
Thanks
Just search the web for "24V radial"!
I remember from my buildup that these companys could have radial-blowers with 24Vdc, but some of them a little bigger then 40mm, maybe 50 or so (you could put a 24vdc-12vdc dcdc-converter to use 12Vdc fans also?):
- sunon
- ebmpapst
- minebea
- sepa
- wallair
- panasonic
... search the web for "ONE-OF-THE-ABOVE-LISTED-VENDOR fan alternative"
Most big electronic-stuff-vendors have really nice websites nowadays where you can just navigate to your product-category, then input your constrains, and it throws back what is left, companies like:
- distrelec
- conrad
- rs-components
- digikey
- mouser
- farnell
- Newark
- element14
... search the web for "ONE-OF-THE-ABOVE-LISTED-VENDOR alternative"
The web might throw up a hundred more companies/vendors! Good luck! Of course you can always with a little risk "gamble"-buy on alibaba, ebay, etc. Most of the stuff just runs fine...
Also you can always make a small circuit where you address the problems with some components to cancel it out, that written here, I am not good at it
EDIT: Sorry for the long post. And yes, I am also using cheap components, they might not come with a 100%-part check, but are budget-friendly
-
@pcsentinel said in Strange failure rate of fans:
I can't use Noctua as they don't do 24V 40mm axial or 40mm
blower and Sunon don't do any small blowers.Just get a step down converter and connect it + output to the middle pin of V_FAN select jumper.
This is really the best solutions since they are much more 12V fans then 24V. -
I really like Delta BFB series. If you can use 12V motors it's a really solid option and pretty quiet at a given flow rating. They have a lot of options to choose from, sometimes as many as five flow rate (RPM) choices for a given package size.
-
EDITEDIT-idea: Maybe increase the 100% startup-time to 5seconds or so to blow out any dust?
Maybe dust and or heat (too close to the extruder?) kill your fans?
I consider myself as lucky, that I could print parts at the local university out of high-temperature-PolyCarbonat on an Ultimaker-3 with which I printed "frames/hinges" with which I could "decouple" the fans thermically from the metal-hotends and other stuff to decrease the risk of a shorted life of those fans because of thermal stress. Having a strong 100% blow when "firing up" the duet2 helps keep the dust out.
-
Getting stiff and hard to start but not getting noisy does sound to me like contamination. I've noticed my hotend fan would really like to suck in any stray hair of filament hanging around the bed area. I expect dust will get in as well. Dust seems to be what usually kills fans in electronic devices. If they don't choke, then they may make it all the way to rattling old age.