Artefacts on walls
-
I am currently running my steppers at 67%
I can give 80% a try.
-
after a long time of testing and adjusting
chaining to different motors -> Still there.
switching to 16 tooth pulley -> Still there but small ripple distance decrease
using Spreadcycle instead of Stealthchop -> Still there , just more motor noise
chaning all toothed idler to smooth ones and twisting the belt -> Still there.
modifying some parts for better belt alignment -> Still there.
upping the current -> Still there
relubricating all the rails -> Still there.i then rotated the part by 45 degrees. this causes the part to be printed by only one motor at a time.
-> The ripples decreased in distance.So i guess i will some 0.9 degrees steppers and combine them with a 16 tooth pulley and see if that helps
-
What are the motors?
-
-
What type of printer is it, which firmware version are you running, and what is your extruder steps/mm ?
-
its a Hypercube Fusion CoreXY with linear rails.
Duet Maestro with Firmware Version: 2.02(RTOS) (2018-12-24b1)
Extruder Steps are 415 for Bondtech BMG -
I'm not and expert on CoreXY machines. I've seen a number of threads about similar artefacts on CoreXY machines. AFAIR the pitch of the artefacts generally matches the belt pitch, and the cause is generally friction. Using non-toothed idlers may also contribute.
Until you resolve this issue, I suggest you use spreadCycle mode for the X and Y drivers, also run them at higher rather than lower current.
-
the steppers havent arrived yet.
but this seems to be a common problem
see these benchys from a prusa.
https://youtu.be/FAXUjZZER5E?t=563 -
@veti said in Artefacts on walls:
the steppers havent arrived yet.
but this seems to be a common problem
see these benchys from a prusa.
https://youtu.be/FAXUjZZER5E?t=563That looks like plain old ringing to me though.
-
ok my 0.9 stepper motors arrived.
Looks ok from this angle
Same Cube, different angle, but still a lot better than before
However now i am getting layer shifts (as seen at the bottom layer), so i have to do some more tuning.
-
the layer shifts were due to the lowered stealthchop -> spreadcycle switchover.
its not that important but i think it would be more consistent to specify the V Parameter in M569 as mm/s rather than clock cycles
-
@veti said in Artefacts on walls:
its not that important but i think it would be more consistent to specify the V Parameter in M569 as mm/s rather than clock cycles
Then we would need to reprogram the stepper drivers when you set the steps/mm. So I compromised with setting the TPWMTHRS value but reporting the corresponding speed too. Also bear in mind that these are belt speeds, which for CoreXY, delta. SCARA| etc. printers are not the same as head speeds.
-
so i bought an ender 3 on sale and was surprised to find the same artefacts on the wall. I have not done much tuning on the machine yet.
This is using a board with marlin 2.0
so am i beeing to picky and there are inherent artefacts for 3d printing?
-
I can think of three likely causes of artefacts like that, that go all the way across the face (not just at the leading edge, which is symptomatic of ringing):
-
Belt issues. If that's the case then the pitch will be related to the belt tooth pitch and will not vary with layer height or extrusion width. A possible cause is the use of smooth idlers instead of toothed ones.
-
Motor issues (least likely). In this case the pitch of the artefacts will be a multiple of full motor steps, most likely it will be 1, 2 or 4 full steps.
-
Extruder issues. In this case then the pitch will decrease if you increase layer height or extrusion width. A possible cause is the use of an ungeared extruder with low steps/mm. Remedies include increasing extruder microstepping, changing from a 1.8deg to a 0.9deg motor, or changing to a geared extruder.
-
