DuetWiFiFirmware minor release 1.15c
-
OK, i put new E firmware in. and Still had the same problem. So i put this into the Config.g file:
M572 D0 S0.00 ; Set extruder 0 pressure advance
M572 D1 S0.00 ; Set extruder 1 pressure advanceproblem is not as bad. in fact just a little bit of Extrusion error now when the program moves to the beginning of the next line
-
Ok, got it to work, this is what i ended up with for a Configuration:
; Configuration file for RepRap Ormerod
; RepRapPro Ltd
;
M111 S0 ; Debug on
M550 PTricolour Mendel WIFI
M551 Pgdww1620
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xEA ; Set the MAC address
M552 S1 ; Enable WiFiM555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; Comms parameters for PanelDue
M906 X800 Y1000 Z800 E800:800 ; Motor currents (mA)M305 P0 R4700 T10000 B3988 ; set bed thermistor parameters
M307 H0 A117.7 C395.8 D1.8 B0
M307 H1 A759.1 C95.9 D5.8 B0M574 X0 S1 ; Set endstop configuration
M574 Y2 S0 ; Set endstop configuration
M574 Z0 S1 ; Set endstop configurationM569 P0 S0 ; Set X Axis Direction
M569 P1 S1 ; Set Y Axis Direction
M569 P2 S0 ; Set Z Axis Direction
M569 P3 S0 ; Set E0 Axis Direction
M569 P4 S0 ; Set E1 Axis DirectionM558 P1 X1 Y0 Z1 ; Set Z probe type
M92 X100.25 Y100.25 Z4001.50 E420.00:420.00 ; Set axis steps per unit
M570 S180 ; Set heater timeout
M667 S0 ; set Cartesian modeM350 X16 Y16 Z16 E16:16 I01 ; Set microstepping mode
M563 P0 D0 H1 ; Create tool 0 = Color 1
M563 P1 D1 H1 ; Create tool 1 = Color 2
M563 P2 D2 H1 ; Create tool 2 = Color 3G10 P0 X20.0 Y0.0 Z0.0 S0 R0 ; Set tool 0 operating and standby temperatures
G10 P1 X20.0 Y0.0 Z0.0 S0 R0 ; Set tool 1 operating and standby temperatures
G10 P2 X20.0 Y0.0 Z0.0 S0 R0 ; Set tool 2 operating and standby temperaturesM106 P2 T45 H1 ; Fan control, Thermostatic on Heater H1
M572 D0 S0.00 ; Set extruder 0 pressure advance
M572 D1 S0.00 ; Set extruder 1 pressure advance;M566 X600 Y600 Z5 E10 ; Set allowable instantaneous speed change
M201 X800 Y800 Z15 E1000:1000 ; acceleration tweaks for improved finish
M203 X15000 Y15000 Z150 E3600:3600 ; speed tweaks for improved finish
;
M208 X200 Y200 Z120 ; set axis max travel
M208 X0.0 Y0.0 Z0.0 S1 ; set axis minimum (adjust to make X=0 the edge of the bed)G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; relative extruder movesG31 P500 Z1.30 ; Set the probe height and threshold PLA = 0.65, ABS = 0.75
T2
M500 ;Store setting in EEPROM -
Are you certain that setting nonzero extruder pressure advance in M572 is causing a problem? Also, have you checked on the web interface or by sending M115 that you really are running firmware version 1.15e? Firmware updates do fail sometimes.
-
No Actually, it just helped. Things started working right when i put the M667 S0 and the M500. I can set the M572 D0 S0.00 to something other then zero. Whats a Recommended value to start with?
-
oww, yes i am running firmware version 1.15e. At least that is what the web interface reads out.
-
No Actually, it just helped. Things started working right when i put the M667 S0 and the M500. I can set the M572 D0 S0.00 to something other then zero. Whats a Recommended value to start with?
Try S values between 0.05 and 0.25. If you are using more than about 2mm of retraction then be prepared to reduce it when you use high S values. For example, using S0.25 will add about 1mm of retraction at the end of a fast printing move.
-
Ok, i set the pressure advance to this, and started a test print
M572 D0 S0.05 ; Set extruder 0 pressure advance
M572 D1 S0.05 ; Set extruder 1 pressure advanceWhen i got to the 1.00mm Z height, the Y axes started to jump, as if it was moving, braking, moving, braking. i killed the print as it was getting pretty load and i was afraid it was going to brake the printer.
-
Ok, Installed the 1.16 Alfa. The Ste-per motor noise is Still there. I did notes its only on coordinated moves. I can calibrate, move the table around and extrude and all is well. But i run a Print and the noise is there. Note - don't get me wrong this is not machanical, its motor drive control
-
OK, This probably needs to be under the next release of the Firmware (dc42/Version 1.16 beta 2), but i could not find a Blog or forum for it. So hear is the info:
- Ste-per motor noise is down to a Dull rorre (Sounds like a Skipping Hart beet). Its still coming out of extrude motor when i listen to it through a Sc-row driver handle.
Temperature control, the best i can do with Auto-tune is the hot end doing +- 0.3. it is holding that. at lest for the short print times i have been testing.
Going to let this test print finish to see if it finushes.
- Ste-per motor noise is down to a Dull rorre (Sounds like a Skipping Hart beet). Its still coming out of extrude motor when i listen to it through a Sc-row driver handle.
-
you have
M350 X16 Y16 Z16 E16:16 I01 ; Set microstepping mode
Should it not be
M350 X16 Y16 Z16 E16:16 I1 ; Set microstepping mode
or
M350 X16 Y16 Z16 E16:16 I0 ; Set microstepping mode
Depending on whether or not you are using interpolation or not?
Also your X and Y axis steps per millimetre are the same but your motor currents are different? are you using different motors?
-
Same motors, one is the Y axes, heavy mechanism, it gets slope if there the same. will fix the M350 command. I uploaded the Firmware (dc42/Version 1.16 beta 3). noisy in the steeper motors is gone.
-
Was ruining another test print. 4mm x 4mm 75mm square. The over extruding started at about 3mm. Looks like its over extruding, then under extruding. Then go's back to normal for 60mm, then it dos it age-an.
-
Was ruining another test print. 4mm x 4mm 75mm square. The over extruding started at about 3mm. Looks like its over extruding, then under extruding. Then go's back to normal for 60mm, then it dos it age-an.
That sounds to me like either a problem with your extuder drive, or inconsistent filament diameter.
-
The filament would have to have a difference of .75mm to do this.
I went from:
M350 X16 Y16 Z16 E16:16 I1 ; Set microstepping mode, interpolation mode On
to
M350 X16 Y16 Z16 E16:16 I0 ; Set microstepping mode, interpolation mode OffSecond test print cam out OK. looks like its interpolation. Docs on Stepper state it needs a Good Clock pulse. Probably is noise or not up to snuf, it also explanes why its a repeting intervall. Adding to mush plastick then not enuff. All leave interpolation mode switched off
-
Figured it out, Extruder issues:
M350 X0 Y0 Z0 E0:0 I0 ; Set microstepping mode
looks like my Stepper motors wont do microstepping mode. If i understand the command right. Symptoms noise steppers, Pore Speed control (Extruder). Switching to latest FW