No fans!

tecno

Tried just use the slider for the ony fan that is there

Falcounet

@tecno The error message seems clear enough to me : You need to define a fan id by adding Pxxx for each M106
See https://docs.duet3d.com/User_manual/Reference/Gcodes/M106

Nightowl

@Falcounet
What have I missed, because it looks like that's exactly what he's done?

tecno

@Falcounet

There is a P0 for the fan need to be gcode controlled or am I missing something

M950 F0 C"out5" Q500                               ; Parts cooling,create fan 0 on pin out5 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value = Gcode controlled. Thermostatic control is turned off

The two other fans have P designations too but to be run continiously.

Falcounet

@Nightowl You are right, I was mixing the M950 and M106 lines

Exerqtor

@tecno
What version of RRF are you running?

tecno

@Exerqtor
Board: Duet 3 Mini 5+ (Mini5plus)
Firmware: RepRapFirmware for Duet 3 Mini 5+ 3.4.0 (2022-03-15)
Duet WiFi Server Version: 1.26

Downloaded today

gloomyandy

@tecno Post your complete config.g file so we can see the full configuration you are using.

tecno

@gloomyandy

; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Jan 07 2023 12:09:54 GMT+0100 (centraleuropeisk normaltid)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Voron01"                                    ; set printer name
M669 K1                                            ; select CoreXY mode
M918 P1 E4 F2000000                                ; configure direct-connect display

; Network
M551 P"bengt"                                      ; set password
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S1                                         ; enable FTP
M586 P2 S1                                         ; enable Telnet

; Drives
M569 P0 S1                                     				; physical drive 0 goes forwards using default driver timings
M569 P1 S1                                     				; physical drive 1 goes forwards using default driver timings
M569 P2 S1                                     				; physical drive 2 goes forwards using default driver timings
M569 P3 S1                                     				; physical drive 3 goes forwards using default driver timings
M584 X0 Y1 Z2 E3                               				; set drive mapping
M350 X16 Y16 Z16 E16 I1                        				; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E690.00             				; set steps per mm
M572 D0 S0.10								   				; PA
M566 X100.00 Y100.00 Z100.00 E600.00           				; set maximum instantaneous speed changes (mm/min)
M203 X5000.00 Y5000.00 Z2600.00 E7200.00       				; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z1500.00 E800.00        				; set accelerations (mm/s^2)
M906 X1250 Y1250 Z400 E800 I25   			   				; set motor currents (mA) and motor idle factor in per cent
M207 S1.5 F7200 Z0.2 				  
M84 S30                                        				; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X120 Y120 Z120 S0                             ; set axis maxima

; Endstops
M574 X2 S1 P"io0.in"                               ; configure switch-type (e.g. microswitch) endstop for high end on X via pin io0.in
M574 Y2 S1 P"io1.in"                               ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin io1.in
M574 Z2 S1 P"io2.in"                               ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin io3.in

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:120 Y15:120 S20                           ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138       ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out1" T0                                 ; create bed heater output on out0 and map it to sensor 0
M307 H0 R1.145 K0.757:0.000 D3.50 E1.35 S1.00 B0   ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4138       ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out2" T1                                 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M140 H1                                            ; map toolhead to heater 1
M143 H1 S300                                       ; set temperature limit for heater 1 to 300C



; Fans
M950 F0 C"out5" Q500                               ; Parts cooling,create fan 0 on pin out5 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value = Gcode controlled. Thermostatic control is turned off
M950 F1 C"out0" Q500                               ; Toolhead cooling, create fan 1 on pin out0 and set its frequency
M106 P1 S1 H-1                                     ; set fan 1 value = always ON. 
M950 F2 C"out6" Q500                               ; Drivers/CPU cooling, create fan 2 on pin out6 and set its frequency
M106 P2 S1 H-1                                     ; set fan 2 value =always ON. 

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

gloomyandy

@tecno What version of DWC are you using? Can you run M98 P"config.g" and post any output. It looks like you may not have a tool selected, so you may need to add T0 at the end of your config.g.

tecno

@gloomyandy
2023-01-07 19:32:13 M98 P"config.g"
HTTP is enabled on port 80
FTP is enabled on port 21
TELNET is enabled on port 23

tecno

What is going on, now next wierd thing, Output 2 toolhead and bed has same Heater name and temp

Nightowl

@tecno
This seems irrelevant to your issue, but the error I get (on my disconnected-from-everything test board) when I run M98 P"config.g" is this:

07/01/2023, 18:42:49	M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: in file macro line 53 column 13: M106: expected number after 'H'
Tool 0: offsets X0.000 Y0.000 Z0.000

Which is the last line on this block from the config.g file:

; Fans
M950 F0 C"fan0" Q500      ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1            ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500      ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H T45          ; set fan 1 value. Thermostatic control is turned on

...showing an error with H - but this is how the RRF Config tool produced the file.

How weird!

tecno

@tecno said in No fans!:

What is going on, now next wierd thing, Output 2 toolhead and bed has same Heater name and temp

FOUND ERROR
M140 H1 ; map toolhead to heater 1 ERASED THIS LINE

tecno

Looks OK and familiar