Updated to RRF 3.4.5, no more toolboards

chrishamm

@gnydick I tried to upgrade my MB6HC + TOOL1LC both using apt and my mainboard once via M997. In both cases the TOOL1LC showed up again as expected:

12/6/2022, 1:28:21 PM 	M115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.4.5 ELECTRONICS: Duet 3 MB6HC v1.01 FIRMWARE_DATE: 2022-11-30 19:35:23
12/6/2022, 1:28:19 PM 	M115 B121
Duet TOOL1LC rev 1.1 or later firmware version 3.4.4 (2022-10-14 11:46:33)
12/6/2022, 1:18:34 PM 	Connection established
12/6/2022, 1:18:20 PM 	M997
12/6/2022, 1:17:56 PM 	M115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.4.5 ELECTRONICS: Duet 3 MB6HC v1.01 FIRMWARE_DATE: 2022-11-30 19:35:23
12/6/2022, 1:17:54 PM 	M115 B121
Duet TOOL1LC rev 1.1 or later firmware version 3.4.4 (2022-10-14 11:46:33)

What errors do you see after the upgrade? Does M115 B121 or M122 B121 work afterwards (provided 121 is your tool board CAN address)?

gnydick

@chrishamm no errors, other than the 40 or so messages about missing heaters, fans, etc when none of them were found after reboot.

I eventually managed to downgrade the firmware on the main board and power cycled a few times and everything came back.

chrishamm

@gnydick What TOOL1LC version are you using? I'd like to reproduce this if possible.

jens55

I just upgraded from 3.4.4 to 3.4.5 and the printer is bricked
The upgrade went as expected, the printer asked if I wanted to upgrade (yes) and it never came back from the disconnection. I did a couple of power cycles to attempt to fix it but no luck.
Looking at my network, the IP from the printer is not present.
Also it looks like all the tool cooling fans (normally temp controlled) are full on.

jens55

Yup, she be bricked alright

paolozampini1973

@jens55 said in Updated to RRF 3.4.5, no more toolboards:

I just upgraded from 3.4.4 to 3.4.5 and the printer is bricked
The upgrade went as expected, the printer asked if I wanted to upgrade (yes) and it never came back from the disconnection. I did a couple of power cycles to attempt to fix it but no luck.
Looking at my network, the IP from the printer is not present.
Also it looks like all the tool cooling fans (normally temp controlled) are full on.

I upgraded today from 3.44 to 3.45 and I haven't had any problems

jens55

@paolozampini1973, hmmmm ..... don't know what to say - "she's dead jim"

What's the best way to downgrade? - Can I just pop out the memory card and install all the files directly from a separate computer ?

Guess I should have made a backup before upgrading - my bad

paolozampini1973

@jens55 said in Updated to RRF 3.4.5, no more toolboards:

@paolozampini1973, hmmmm ..... don't know what to say - "she's dead jim"

What's the best way to downgrade? - Can I just pop out the memory card and install all the files directly from a separate computer ?

Guess I should have made a backup before upgrading - my bad

dwc

jens55

@paolozampini1973, with a lot of help from @chrishamm I was able to re-flash the firmware and am now back in business.

oliof

@jens55 on 3.4.4 or 3.4.5?

jens55

@oliof, not clear on what you are asking but I went from 3.4.4 to 3.4.5 which failed. I then installed 3.4.5 using bossa and that worked.

dc42

@jens55 said in Updated to RRF 3.4.5, no more toolboards:

@oliof, not clear on what you are asking but I went from 3.4.4 to 3.4.5 which failed. I then installed 3.4.5 using bossa and that worked.

SBC mode or standalone?

jens55

@dc42, standalone

dc42

@jens55 did you upload the zip file, or did you attempt to update the firmware in some other way?

jens55

@dc42, I uploaded the zip file, it unpacked successfully, it asked me if I wanted to install the new firmware (I said yes) and did it's thing. The printer disconnected and then never reconnected.
Once I had bossa up and running, before I did anything else, I did a 'verify' and tat actually failed so something was corrupt. I then replaced the firmware with bossa, disconnected the usb cable and powered up and all was well

dc42

@jens55 thanks. Which main board do you have?

jens55

@dc42 6HC

digitalsolo

Another 3.4.5 (MB6HC, SBC) with Toolboard 1LC 1.3. Toolboard is gone after firmware update to 3.4.5.

I've done lots of poking at it (initially it was a 2 blink, no firmware) now it's a 3 blink (bad CRC). I forced downgrade to 3.4.4, etc. No dice.

I have a thread on the Firmware board about it also:
https://forum.duet3d.com/topic/30641/toolboard-firmware-issues/

gnydick

@chrishamm my boards are 1.3