Ender 3 RRF v1.1 setting up BLtouch

[re_tour]

@gixxerfast Hey there! So today I've tried the mesh and it works! This is what I see after running it:

So now all is left is to slice the things I want in Cura and upload the gcode which I get?

[re_tour]

So I started the print, and the filament started to go in the opposite direction. I haven't the slightest clue why.

[Gixxerfast]

@re_tour Hi there, reverse the extruder motor

M569 P3 S0

[re_tour]

@gixxerfast said in Ender 3 RRF v1.1 setting up BLtouch:

M569 P3 S0

Thank you so much. Do I have to reverse it every time I turn the printer on or was it just an initial setting mistake I didn't pay attention to?

[Gixxerfast]

@re_tour No, just change it once in config.g and it wasn't a mistake. Really hard to know how the wires are supposed to be, just as long as the pairs are correct it's good. Many has to adjust that AFAIK.

[re_tour]

@gixxerfast Thank you very much!

[re_tour]

@gixxerfast So I didn't input that change into the config.g yet, but wrote it into the console. Printed 2 things, the strange thing is that at the end of each print the mechanism pulls the filament all the way out. Why could that be?

[Gixxerfast]

@re_tour You must have something wonky in your slicer. Check if there some custom end print gcode in Cura (it was Cura you were using, right?)

[re_tour]

@gixxerfast Yes sir, let me check.

[re_tour]

@gixxerfast This is the last few lines of the first gcode:

;TIME_ELAPSED:2311.874865
G1 F2700 E788.98313
M140 S0
M107
G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-2 Z0.2 F2400 ;Retract and raise Z
G1 X5 Y5 F3000 ;Wipe out
G1 Z10 ;Raise Z more
G90 ;Absolute positioning

G1 X0 Y235 ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed

M84 X Y E ;Disable all steppers but Z

M82 ;absolute extrusion mode
M104 S0
;End of Gcode

and the end of the second gcode:

;TIME_ELAPSED:10192.122505
G1 F2700 E523.83295
M140 S0
M107
G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-2 Z0.2 F2400 ;Retract and raise Z
G1 X5 Y5 F3000 ;Wipe out
G1 Z10 ;Raise Z more
G90 ;Absolute positioning

G1 X0 Y235 ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed

M84 X Y E ;Disable all steppers but Z

M82 ;absolute extrusion mode
M104 S0
;End of Gcode

[Gixxerfast]

@re_tour said in Ender 3 RRF v1.1 setting up BLtouch:

G1 E-2 F2700 ;Retract a bit G1 E-2 Z0.2 F2400 ;Retract and raise Z

I really don't have a clue. I'm just guessing but...

Try to find where these are inserted

And comment them out /remove them.

See if it makes any difference.

[re_tour]

@gixxerfast You were right, G1 E-2 F2700 pulls the filament nearly all the way out. Thank you (once again)

[Gixxerfast]

@re_tour That's great!
Happy printing!

I think you might have to revisit the offset configuration. The mesh looked a bit shifted. But that's for another day

and as long as it prints and you get the first layer right, it works