PanelDue Firmware 3.3.0-rc3 released

mfs12

Release Notes 3.3.0-rc3

This release requires RepRapFirmware 3.3 or later.

Version 2 (after August 2016) and Version 3 PanelDue are supported.

Features:

added Russian translation
added support for emerging backlight mp3302 chip
renamed 'Print' tab into 'Status'
added slicer time
added simulated time
removed layer time
faster and consistent display of printer status
display IP address of printer in Setup tab
adaption to changes of object model
allow assignment of fans, extruders and heaters to multipls beds, chambers or tools
added debugging interface to write debugging information as gcode comments to the reprap uart

Bug fixes:

gracefully handle parsing errors in M409 K"<key>" requests
show warning instead of error when JSON parsing errors occur
fix displaying of percent sign
fix displaying of M291 dialogs
fix sending filename in M37
fix unresponsive screen when showing m291 message while screensaver is active
fix updating of simulated time left during print

Downloads and flashing instructions:

Binaries can be found at https://github.com/Duet3D/PanelDueFirmware/releases/tag/3.3.0-rc3

Flashing instructions can be found at https://duet3d.dozuki.com/Wiki/PanelDue_Firmware_update

mfs12

Right on time before the weekend the hopefully last release candidate. Some minor but relevant changes were introduced. Check the release notes.

I am very happy about any feedback. But most interested in bug reports

And thanks to all people who tested, reported bugs and brought new ideas to the project.

MartinNYHC

What's up here....strange colors The white is yellow.

PanelDue 7 V3 just updated to 3.3.0-RC3 (PanelDueFirmware-3.3.0-rc3-v3-7.0.bin).

Phaedrux

@martinnyhc If you flash back to previous version does it improve?

Are you sure you have a V3 and not a 7i?

MartinNYHC

Yes, it's a V3 on my old printer.

Just changed to RC2 and then to RC3 again and now it looks good. Strange....

mloidl

The simulated times left seems be to shown correctly after a print with 3.3.0-rc3.
Thanks a lot @mfs12 for the fix.

Aitor

Good morning @mfs12,

I have been doing more tests with PanelDue 3.3.0-rc3, and I have seen that M291 S2 or S3, X1 Y1 Z1... do not show the scrolling panel, in web control they do appear.

Anyway I have also tried in the following versions without success:
PanelDue 3.3.0-rc2
PanelDue 3.2.11
PanelDue 1.24

The duet2 wifi firmware was always in 3.3, I'm almost sure that these were shown in 1.24, so I'm not sure if it's something of the paneldue.

This is the code that doesn't work, am I doing something wrong?

M291 R "MOVE X" P "select position X" S2 X1

Best regards and thanks

mfs12

@aitor actually there were some major changes from paneldue 1.24 to 3.x.

I can't confirm that the message is not displayed to me. Although it's quite delayed since sending the command until message dialog is displayed.

My process:

start paneldue, rrf and dwc
connect dwc to duet3
send command 'M291 R "MOVE X" P "select position X" S2 X1'

In dwc it's instantly displayed. On paneldue the message is delayed up to 1-2s if screen is active, if screensaver is active it's delayed up to 8s.

Aitor

Good morning @mfs12 ,

The message is displayed, the scroll bar is the one that is not displayed.

As you say in dwc it is displayed instantly. In the panel, the message is delayed up to 1-2 seconds if the screen is active, if the screen saver is active, it is delayed up to 8 seconds, but the scrollbar is not displayed

My process: