Connect a water flow sensor --> will M591 P7 work in Laser mode?

cosmowave

@paulg4h
you should have a look to the object model for correct naming... i'm not at the machine...
But it will be something like this:

if fans[n].rpm < xxx
    M25

paulg4h

@cosmowave
this is now my daemon.g content

if job.duration = null
    ; No job ignore sensor reading
else
    ; Check Water Flow
    if fans[0].rpm < 100
        G4 P10
        if fans[0].rpm < 100
            G4 P10
            if fans[0].rpm < 100
                M25
                M118 S"No Water flow!" 
    ; Check water temperature
    if sensors.analog[0].lastReading > 35
        G4 P10
        if sensors.analog[0].lastReading > 35
            G4 P10
            if sensors.analog[0].lastReading > 35
                M25
                M118 S"Water to hot!"

paulg4h

@dc42 @cosmowave

Now even with three times reading the rpm and the delay the job pauses with the message no water flow.

How can I prevent this?

cosmowave

@paulg4h
First: check if your rpm is > 100

paulg4h

@cosmowave this works now, many thanks!

paulg4h

For everyone now the water flow sensor and even the water temperature monitored by RRF worked and pause the job when the water flow is to low or the water temperature is to high.

I use the YF-S201 as Flow Meter connected to the SKR 1.4T Board on the BLTouch Connector (servo and probe) pins. The thermistor is connected to the bed thermistor input also.

then I add in config.g

; Tools --> Laser Water Flow
M950 F0 C"!fan0+^probe"                          ; Fan 0 uses the Fan0 output, but we are using a PWM fan so the output needs to be inverted, also we are using probe as a tacho input with pullup resistor enabled

; Tools --> Laser Water Temperature
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp

then add the daemon.g file with this content too:

if job.duration = null
    ; No job ignore sensor reading
else
    ; Check Water Flow
    if fans[0].rpm < 100
        G4 P10
        if fans[0].rpm < 100
            G4 P10
            if fans[0].rpm < 100
                G4 P10
                if fans[0].rpm < 100
                    M25                            ; pause job
                    M118 S"No Water flow!"         ; write msg
    ; Check water temperature
    if sensors.analog[0].lastReading > 35
        G4 P10
        if sensors.analog[0].lastReading > 35
            G4 P10
            if sensors.analog[0].lastReading > 35
                M25                                 ; pause job
                M118 S"Water to hot!"               ; write msg

Many thank's for all your help!

o_lampe

@paulg4h
Thanks for sharing!
I'm just wondering, if there's a different way to code this (G4 P10)?
Eg. using a counter variable or iteration?
You can keep it like that, but if there's more code in daemon.g (for Lid control?) you don't want daemon.g to stick in a if-iteration with lots of G4.

paulg4h

@o_lampe You are right, this is not perfect, maybe I found a better way without G4 P10 but for the lid control this doesn't matter because this is handled by triggers and works without G4

o_lampe

@paulg4h
I'm sure you know it already, just wanted to mention that daemon.g runs only every 10 seconds. So you already have a G4 P10 'incorporated'.
Just have to count, how many times in a row your sensors were outside of the zone.

dc42

@o_lampe said in Connect a water flow sensor --> will M591 P7 work in Laser mode?:

@paulg4h
I'm sure you know it already, just wanted to mention that daemon.g runs only every 10 seconds. So you already have a G4 P10 'incorporated'.
Just have to count, how many times in a row your sensors were outside of the zone.

G4 P10 waits for 10 milliseconds. G4 S10 would wait for 10 seconds.

To reduce the number of accesses to the SD card, it's best to use an explicit loop in daemon.g like this:

while true
  G4 S2
  ... rest of code ...

This saves RRF from having to keep re-opening the file. You can change S2 to however many seconds you want to wait between tests.

paulg4h

@dc42 thanks for the input.

After changing of the daemon.g I am not able to update the file by DWC because it is now opened forever.

How can I update the daemon.g beside change the file on SD card now?

dc42

@paulg4h said in Connect a water flow sensor --> will M591 P7 work in Laser mode?:

@dc42 thanks for the input.

After changing of the daemon.g I am not able to update the file by DWC because it is now opened forever.

How can I update the daemon.g beside change the file on SD card now?

Rename the daemon.g file from DWC, then reset.

paulg4h

@dc42 Thank's again!

How could I use the rpm more reliable to detect water flow, even in DWC the Sensors Fan RPM are shown and jumps between 0 and something between 190 and 210 all the time.

What is the best in sort of functionality and use as low as possible resources in RRF?

paulg4h

Is there anybody who can show the best way to monitor such an sensor where the reading is not reliable on RRF 3.3?

Many thanks!

cosmowave

@paulg4h I think, it is a signal problem. Do you have an oscilloscope for checking the signal?

paulg4h

@cosmowave For me it looks like that RRF is not able to count the signal (rpm) because the DWC which pools the values every second shows as example 207 - 0 - 196 - 0 - 201 - 0 -198 - 0 so every two seconds I get zero.

How to use a variable to calculate a avg value to get a relieable value I can use to decide that the water flow is still there?

cosmowave

@paulg4h Eventually you can make a sum of e.g. 10 measurements of the value and take the average of these measurements. When the average is below a value (e.g. 20) then you have no flow.

It will be a littel slower, but i think, that is no problem...

paulg4h

@cosmowave so create 10 position variables and one counter and avg or is there a type of list /array available too?
How to create such a script that it uses as less ressources of the system as posible?

There is an variable type of array but I have no clue how to assign a value or sum the values to get an AVG with the informations provided there.

cosmowave

@paulg4h or something like this in daemon.g

 var.counter
 var.sum

if var.zähler < 10
	set var.sum = {var.sum + "newValue"}
	set var.counter = var.counter + 1

else 
	if {var.sum / var.counter} < 20
		NO FLOW

paulg4h

@cosmowave this will not work because as more readings the sum gets as less the chance that the avg value comes close to the low value.

There should be something like a array with 10 values which are overwritten every 10 readings to get an reliable value.