[3.3-rc1] Strange error on PanelDue
-
Since upgrading to 3.3-rc1 I get an error on my console.
Was not there running the 3.3 b3
Regards,
Paul. -
@paulhew do you get this message frequently? Or once on start up? If you get it frequently, does anything in particular trigger it?
Please post your config.g file.
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
@dc42 As requested
; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"RailCoreII" ; set printer name M669 K1 ; select CoreXY mode G4 S1 ; wait for expansion boards to start ; Drives M569 P0.0 S1 ; X Axis - physical drive 0.0 goes forwards M569 P0.1 S0 ; Y Axis - physical drive 0.1 goes backwards M569 P0.2 S1 ; Left Front physical drive 0.2 goes forwards M569 P0.3 S1 ; Left Rear physical drive 0.3 goes forwards M569 P0.4 S1 ; Right physical drive 0.4 goes forwards M569 P20.0 S0 ; Extruder - physical drive 20.0 goes forwards M584 X0.0 Y0.1 Z0.2:0.3:0.4 E20.0 ; set drive mapping ; M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation ; M92 X200.00 Y200.00 ; set steps per mm M92 Z1600 ; set steps per mm Z Axis M92 E412 ; set steps per mm Extruder ; M566 X600.00 Y600.00 Z200.00 E3600.00 ; set maximum instantaneous speed changes (mm/min) M203 X18000.00 Y18000.00 Z900.00 E3600.00 ; set maximum speeds (mm/min) M201 X1500.00 Y1500.00 Z250.00 E1500.00 ; set accelerations (mm/s^2) M906 X1280 Y1280 Z1220 E700 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Leadscrew locations ;New 4-2-21 M671 X-1:-1:350 Y24:281:151 S7.5 ; Axis Limits ;M208 X0 Y0 Z0 S1 ; set axis minima ;M208 X230 Y300 Z400 S0 ; set axis maxima M208 X-10:300 Y0:300 Z-0.5:500 S0 ; Endstops M574 X1 S1 P"io5.in" ; configure active-high endstop for low end on X via pin io5.in M574 Y1 S1 P"20.io2.in" ; configure active-high endstop for low end on Y via pin 20.io1.in ; Z-Probe - ToolBoard 1LC M950 S0 C"20.io0.out" ; create servo pin 0 for BLTouch M558 P9 C"^20.io0.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X-7 Y35 Z0.904 ; set Z probe trigger value, offset and trigger height ;M557 X15:215 Y15:195 S20 ; define mesh grid M557 X30:280 Y45:280 S20 ; Z-Probe - Using io_1 ;M950 S0 C"io1.out" ; create servo pin 0 for BLTouch ;M558 P9 C"^io1.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds ;G31 P500 X-7 Y35 Z2.5 ; set Z probe trigger value, offset and trigger height ;M557 X15:215 Y15:195 S20 ; define mesh grid ; Heaters M308 S0 P"temp0" Y"thermistor" A"Heated Bed" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out1 and map it to sensor 0 ;M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M307 H0 R0.853 C250.9 D5.98 S0.60 ; tuned to 50degrees - 28/3/21 M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"20.temp0" Y"thermistor" A"Mosquito" T500000 B4723 C1.19622e-7; configure sensor 1 as thermistor on pin 20.temp0 M950 H1 C"20.out0" T1 ; create nozzle heater output on 20.out0 and map it to sensor 1 ;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 ; set temperature limit for heater 1 to 280C ;M307 H1 R1.632 C237.7 D6.86 S1.00 V24.2 M307 H1 B0 R1.480 C221.2:201.5 D7.80 S1.00 V24.0 ; Other Thermistors M308 S2 P"temp1" Y"thermistor" A"Bed-Top" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M308 S3 P"20.temp1" Y"thermistor" A"Chamber" T100000 B4138 ; Fans M950 F0 C"20.out1+out1.tach" Q500 ; create fan 0 on pin 20.out1 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"20.out2" Q500 ; create fan 1 on pin 20.out2 and set its frequency M106 P1 S1 H1 T50 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ;Lights M950 F10 C"out1" M106 P10 S0 H-1 C"Front Lights" M106 P10 S1 M150 X1 Q3000000 ; Configure NeoPixel channel M150 R000 b000 u000 P128 S60 ; Turn them all off if on ; Custom settings are not defined ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue T0 ; select first hot endRegards
Paul -
Does not happen when printer is booted from power off
Duet Mini 5+ and SBCSaw it when it started a print, will see if the error comes up again.
-
Just homed the printer, bed was about 150mm down, XY ok and after Z a new message appeared on the PanelDue.
m122 === Diagnostics === RepRapFirmware for Duet 3 Mini 5+ version 3.3RC1 (2021-05-01 09:59:28) running on Duet 3 Mini5plus Ethernet (SBC mode) Board ID: A45XG-F396U-D65J0-40KML-1F03Z-H03XPm122 b20 Diagnostics for board 20: Duet TOOL1LC firmware version 3.3beta2+1 (2021-04-07 10:51:19) Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)Regards,
Paul
