BLtouch does not work after changing to DUEX5 board

Javajoeuk

my bl touch v3.1 was staying red on startup when it could not complete its self test. I thought it was the wiring after moving it upto the printer and extending the cables but they tested ok and after reading someone elses post they mentioned the grub screw which I had not touched. So I gave it a little adjustment turned the printer back on and it completed it self test straight away as normal. Give it a go it might work.

Haggan90

@Javajoeuk Ok! I will test that!
You mean the little screw on the top of the BLTouch right?

Javajoeuk

yes be gentle.

Haggan90

@Javajoeuk Tried it with no success, it won't activate for some reason..
Any other idea?

Javajoeuk

no sorry

Haggan90

@Phaedrux Do you find anything strange in the config?

Veti

can you try a different pwm port?

Haggan90

@Veti Yes of course, which heater do I need to disable if I wan to use PWM_2?

Veti

try 5 or 7. they are often used for bltouch

dc42

@Haggan90 said in BLtouch does not work after changing to DUEX5 board:

@Veti Yes of course, which heater do I need to disable if I wan to use PWM_2?

Try disabling heater 7 and use PWM5 on the DueX, that's a common combination.

Haggan90

@dc42 Thank you, I will try that!

Haggan90

@dc42 said in BLtouch does not work after changing to DUEX5 board:

@Haggan90 said in BLtouch does not work after changing to DUEX5 board:

@Veti Yes of course, which heater do I need to disable if I wan to use PWM_2?

Try disabling heater 7 and use PWM5 on the DueX, that's a common combination.

Do I need to change anything more then this: M307 H7 A-1 C-1 D-1 ?
And remove the M307 from config-override.g

Phaedrux

You'll also have to update your deploy and retract macros to reference the new pin number as well.

Haggan90

@Phaedrux Should that be M280 P5 S10 then?

Phaedrux

P7 for heater pin 7

By the way using pins gets a lot easier in RRF3. Might be time to consider updating.

Haggan90

@Phaedrux Right now I just want the printer to work again, been down for almost a year now

Changing to heater 7 did not work, still the same problem..

Phaedrux

Please post the current version of your config.g, config-override.g, deploy and retract macros, and please double check which pin you're connected to. And refresh me on which wires are going where.

Haggan90

@Phaedrux Ok!
Config.g


; General preferences
G21												; work in millimeters
G90                                             ; Send absolute coordinates...
M83                                             ; ...but relative extruder moves

; Network
M552 S1                                         ; Enable network
M586 P0 S1                                      ; Enable HTTP
M586 P1 S0                                      ; Disable FTP
M586 P2 S0                                      ; Disable Telnet


; Drives						
M584 X6 Y1 Z2:5:4 E3							; set 3 Z drivers
M569 P1 S0                                      ; Drive 1 goes backwards
M569 P2 S0                                      ; Drive 2 goes backwards
M569 P3 S1                                      ; Drive 3 goes forwards
M569 P4 S1                                      ; Drive 4 goes forwards
M569 P5 S0                                      ; Drive 5 goes backwards
M569 P6 S1                                      ; Drive 6 goes forwards

M669 K0 Y-1.005:1:0:							; set Y to react with X

; Defining X and Y coordinates of the leadscrews
M671 X-80:580:580 Y245:490:0 S5 				; leadscrews at front right, rear right and middle left

M350 U16 X16 Y16 E16 Z16 I1                    	; Configure microstepping with interpolation
M92  X133.33 Y242.00 Z200 E415.00      			; Set steps per mm
M566 X900.00 Y900.00 Z20.00 E200.00		     	; Set maximum instantaneous speed changes (mm/min)
M203 X15000.00 Y15000.00 Z600.00 E3600.00		; Set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z30.00 E3000		     	; Set accelerations (mm/s^2)
M906 X1000.00 Y1500.00 Z1000.00 E700.00 I30 	; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                         ; Set idle timeout


;Energize Z steppers
M906 I100 										; prevent idle current reduction
G91 											; relative mode
G1 S2 Z0.1 										; energize all 3 motors
G90 											; absolute mode

; Axis Limits
M208 X0 Y0 Z0 S1                       	 		; Set axis minima
M208 X500 Y500 Z750 S0                 			; Set axis maxima

; Endstops
M574 X1 S0										; Set active low endstops
M574 Y2 S1                               		; Set active high endstops

; Pressure advance
M572 D0 S0.05

; BLTouch - Heaters
M307 H7 A-1 C-1 D-1 							; Disable the Heater7 to free up PWM channel 5 on the Duex board

; Z-Probe
M574 Z1 S2 										; Define Z to use Probe. Home to Min.
M558 P9 H5 F100 T2000							; Set Z probe type/mode 9.
G31 P50 X0 Y73.8 Z2.55							; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
M557 X0:500 Y0:400 S100							; define mesh grid



; Heaters
M140 H-1 					; Disable heated bed

;M305 P0 T100000 B4138 R4700                    ; Set thermistor + ADC parameters for heater 0
;M143 H0 S120                                   ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                     ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                                   	; Set temperature limit for heater 1 to 280C
.

; Fans
M106 P0 S0 I0 F600 H-1                        	; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                       ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                ; tool 0 uses extruder 0 and heater 1
G10 P0 X0 Y0 Z0 R0 S0                           ; set tool 0 offsets and temperatures


M501;

; Automatic saving after power loss is not enabled

; Custom settings are not configured

Config-override.g


0:/sys/config-override.g
; config-override.g file generated in response to M500
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 A90.0 C700.0 D10.0 S1.00 V0.0 B1
M307 H1 A351.8 C150.9 D9.0 S0.80 V24.4 B0
M307 H2 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H4 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H5 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H6 A340.0 C140.0 D5.5 S1.00 V0.0 B0

G10 L2 P1 X0.00 Y0.00 Z0.00 U0.00
G10 L2 P2 X0.00 Y0.00 Z0.00 U0.00
G10 L2 P3 X0.00 Y0.00 Z0.00 U0.00
G10 L2 P4 X0.00 Y0.00 Z0.00 U0.00
G10 L2 P5 X0.00 Y0.00 Z0.00 U0.00
G10 L2 P6 X0.00 Y0.00 Z0.00 U0.00
G10 L2 P7 X0.00 Y0.00 Z0.00 U0.00
G10 L2 P8 X0.00 Y0.00 Z0.00 U0.00
G10 L2 P9 X0.00 Y0.00 Z0.00 U0.00

My Duet
Send code...
Status
Idle
Tool Position
X
0.0
Y
0.0
Z
0.10
Extruder Drives
Drive 0
0.0
Speeds
Requested Speed
0 mm/s
Top Speed
0 mm/s
Sensors
Vin
24.5 V
MCU Temperature
33.2 C
Fan RPM
0
Z-Probe
0
 Tools
 Extra
 Control All
Tool	Heater	Current	Active	Standby
Tool 0
T0 - Load Filament	Heater 1
off	22.1 C	
0
0
Temperature Chart
System Directory

deploy

; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v2 on Tue Nov 20 2018 21:58:16 GMT+0100 (centraleuropeisk normaltid)
M280 P7 S10

Retract

; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v2 on Tue Nov 20 2018 21:58:16 GMT+0100 (centraleuropeisk normaltid)
M280 P7 S90

Phaedrux

Does the BLTouch do a self test at power on?
Does sending M401 and M402 deploy and retract the pin?

Haggan90

@Phaedrux said in BLtouch does not work after changing to DUEX5 board:

Does the BLTouch do a self test at power on?
Does sending M401 and M402 deploy and retract the pin?

No it does not.
Nothing hapends at all.. The bltouch just lights constantly red.