Mini 5 no heaters
-
Solved TLDR version is that it was a firmware missmatch
So my very clued up uncle gifted me a Mini 5 wifi and Toolboard as a christmas present
On my modified prusa clone i had a duet2 wifi running fine on RRF3
I installed the mini 5, it moves and homes fine but when i try to operate the heaters, both the bed and hot end, nothing happens
The hot end is set to out1 on the toolboard and the thermistor set to temp1
The bed heater is 220v Mains powered with a SSR on out 2 on the mainboardIn DWC the hotend button is red and when i click on it to set it to active i cant
With the bed i can set it to active but when i set a temp again nothing happens.
im at a loss as to why this is as the config is simple enough and I used most of the config i was succesfully running on the duet2 .
I have attached my config.g
And a picture of my wiring does anyone have any idea as to what i have done wrong ?
;i3 config ; 1. General Preferences G90 ; Machine movement to use absolute coordinates M83 ; Extruder to use relative moves M550 P"Mega-3" ; Machine name ; 2. Network M552 S1 ; Network is enabled and acquires a dynamic address via DHCP M586 P0 S1 ; HTTP is enabled M586 P1 S0 ; FTP is disabled M586 P2 S0 ; Telnet is disabled ; 3. Drives M671 X-70:410 Y170:170 S25 ; The Z axis pivot point locations to allow levelling to be undertaken M569 P0.0 S1 ; Drive 0.0 (Y Axis Motor) goes forwards M569 P0.1 S1 ; Drive 0.1 (Z1 Axis, Left Motor) goes forwards M569 P0.2 S1 ; Drive 0.2 (Z2 Axis, Right Motor) goes forwards M569 P0.3 S1 ; Drive 0.3 (X Axis Motor) goes forwards M569 P121.0 S1 ; Drive 121.0 (E0, Extruder Motor) goes forwards and is mapped to the Tool-Board-LC1 M584 X0.3 Y0.0 Z0.1:0.2 E121.0 ; Drive mapping M350 X16 Y16 Z16 E16:16 I1 ; Microstepping with interpolation M92 X80.00 Y100.00 Z400.00 E420.00:420.00 ; Steps per mm M566 X900.00 Y900.00 Z60.00 E120.00:120.00 ; Maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; Maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; Accelerations (mm/s^2) M906 X1200 Y1200 Z800 E800:800 I30 ; Motor currents (mA) & motor idle factor % M84 S30 ; Idle timeou ; 4. Axis Limits M208 X-28 Y0 Z-1 S1 ; Axis min M208 X350 Y350 Z350 S0 ; Axis max ; 5. Endstops M574 X1 S1 P"121.io1.in" ; X Axis endstop is at the low end and mapped to pin 121.io1.in on the Tool-Board-LC1 M574 Y1 S1 P"io1.in" ; Y Axis endstop is at the low end and mapped to pin io1.in on the Main Board M574 Z1 S2 ; The Z probe acts as a Z axis endstop & is located at Z axis's minimum & mapped/connected to the io0 port on the toolboard LC1 ; 6. Z-Probe M558 P8 C"121.io0.in" H5 F100 T6000 ; The Z probe is of type 8 & is mapped/connected to 121.io0.in port on the toolboard LC1 G31 P50 X11 Y0 Z0.728 ; Z probe trigger value, offset and trigger height M557 X45:370 Y8:330 S20 ; Mesh grid parameters ; 7. Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; Sensor 0 is a thermistor on temp0 M950 H0 C"out2" T0 ; Bed heater is on output on out2 & mapped to sensor 0 M307 H0 B1 S1.00 ; Bed heater is set to bang-bang mode & set PWM limit M140 H0 ; Bed heater is mapped to heater 0 M143 H0 S120 ; Temperature limit for the bed heater is set to 120C M308 S1 P"121.temp1" Y"thermistor" T100000 B4138 ; Sensor 1 is a thermistor & mapped to pin 121.temp1 on the Tool-Board-LC1 M950 H1 C"121.out0" T1 ; The Hot end heater outputs on 121.out0 and is mapped to sensor 1 on the Tool-Board-LC1 M307 H1 B0 S1.00 ; The Hot end heater is set to ise PID & set PWM limit M143 H1 S310 ; Temperature limit for the Hot end heater is set to 310C ; 8. Fans M950 F0 C"121.out2" Q500 ; Fan 0 is mapped to pin 121.out2 on the Tool-Board-LC1 M106 P0 S0 H-1 ; Set fan 0 value. Thermostatic control is turned off ;M950 F1 C"121.out1" Q500 ; Create fan 1 on pin 121.out1 and set its frequency ;M106 P1 S1 H1 T45 ; Set fan 1 value. Thermostatic control is turned on ; 9. Tools M563 P0 S"Hot-End" D0 H1 F0 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; 10. Miscellaneous T0 ; Select first tool
-
@JayJay said in Mini 5 no heaters:
The hot end is set to out1 on the toolboard and the thermistor set to temp1
M950 H1 C"121.out0" T1
this does not match.
M950 H0 C"out2" T0
hard to see in the image, but try out0 thats meant for the bed.
also see the current limitations
https://duet3d.dozuki.com/Wiki/Duet_3_firmware_configuration_limitationsdid you update the firmware on both the mini and the toolboard?
-
This post is deleted! -
what is wrong with his heater code ?
i have very similar on my corexy and it works fine, im genuinely interested in seeing what you think is wrong with it.
if he has the heater wired to the tool-board in the following manner
heater cartridge = out0
thermistor = temp1then what should the g code be ?
-
he wrote he connected it to out1 but wrote out0 in the code
-
@Veti said in Mini 5 no heaters:
he wrote he connected it to out1 but wrote out0 in the code
we will need a picture of the tool-board to check that.
@JayJay please post a picture of your tool-board wiring
-
Thank you all for the input.
@Veti thanks for the advice on moving the heater wires, i used out2 because i have an SSR and thought it would be ok to use, i moved the wires to out0 and changed the config, and now the bed heater works.
I also updated the toolboard firmware to Duet TOOL1LC firmware version 3.2-RC2 (2020-12-24)
And now since doing that the temp reading has dissappeared and shows n/a where as before it did show the correct temp, and i can now click on the hot end button and activate it but as there is no temp reading i get a fault, so i just need to work on that now.
@CaLviNx
my originalpost about the toolboard being on out1 is a typo it is wired into out0 same as the config.
-
can you post the M122 of both the mini and the toolboard. maybe there is a can communication problem.
-
@Veti said in Mini 5 no heaters:
can you post the M122 of both the mini and the toolboard. maybe there is a can communication problem.
i also tried moving the thermistor to temp0 and that shows as n/a also
M122 === Diagnostics === RepRapFirmware for Duet 3 Mini 5+ version 3.2-beta3.2+1 running on Duet 3 Mini5plus WiFi (standalone mode) Used output buffers: 3 of 40 (11 max) === RTOS === Static ram: 97472 Dynamic ram: 132764 of which 368 recycled Never used RAM 30516, free system stack 176 words Tasks: NETWORK(ready,168) HEAT(blocked,195) CanReceiv(blocked,875) CanSender(blocked,371) CanClock(blocked,370) TMC(blocked,56) MAIN(running,448) IDLE(ready,20) AIN(blocked,258) Owned mutexes: === Platform === Last reset 00:03:29 ago, cause: software Last software reset at 2020-12-29 14:51, reason: User, GCodes spinning, available RAM 30516, slot 2 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN Error status: 0x00 Supply voltage: min 0.0, current 23.6, max 23.6, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0 Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0 Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0 Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0 Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0 Driver 5: position 0, assumed not present Driver 6: position 0, assumed not present Date/time: 2020-12-29 14:55:14 Slowest loop: 10.22ms; fastest: 0.12ms === Storage === Free file entries: 10 SD card 0 detected, interface speed: 22.5MBytes/sec SD card longest read time 3.3ms, write time 4.7ms, max retries 0 === Move === Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms Bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = 0 -1, chamberHeaters = -1 -1 Heater 0 is on, I-accum = 0.0 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 SBC is idle in state(s) 0 Daemon is idle in state(s) 0 Aux2 is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 26.88ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 1 of 8 - WiFi - Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.25beta0 WiFi MAC address f4:cf:a2:6f:bd:af WiFi Vcc 3.38, reset reason Power up WiFi flash size 2097152, free heap 26680 WiFi IP address 192.168.0.115 WiFi signal strength -48dBm, mode 802.11n, reconnections 0, sleep mode modem Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0 === CAN === Messages sent 0, send timeouts 0, longest wait 2ms for type 6049, free CAN buffers 15 M122 B121 Diagnostics for board 121: Duet TOOL1LC firmware version 3.2-RC2 (2020-12-24) Bootloader ID: not available Never used RAM 4176, free system stack 96 words HEAT 90 CanAsync 89 CanRecv 83 TMC 54 MAIN 324 AIN 64 Last reset 00:05:42 ago, cause: software Last software reset data not available Driver 0: position 0, 80.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 51, reads 39933, writes 10, timeouts 0, DMA errors 0 Moves scheduled 0, completed 0, in progress 0, hiccups 0 No step interrupt scheduled VIN: 24.0V MCU temperature: min 32.2C, current 32.6C, max 32.6C Ticks since heat task active 61, ADC conversions started 342054, completed 342053, timed out 0 Last sensors broadcast 0x00000000 found 0 64 ticks ago, loop time 0 CAN messages queued 2765, send timeouts 0, received 3098, lost 0, free buffers 36 -
@JayJay said in Mini 5 no heaters:
RepRapFirmware for Duet 3 Mini 5+ version 3.2-beta3.2+1
you did not do the update to 3.2-RC2
after the update power the entire system down and up again
-
@Veti said in Mini 5 no heaters:
@JayJay said in Mini 5 no heaters:
RepRapFirmware for Duet 3 Mini 5+ version 3.2-beta3.2+1
you did not do the update to 3.2-RC2
after the update power the entire system down and up again
hmmm i dont know why it is saying that as i definately downloaded the rc2 candidate from github
i uploaded it to the board and it asked me if i wantted to update which i did.
i think the correct file is : Duet3Firmware_Mini5plus.uf2
and : Duet3_SDiap32_Mini5plus.bin -
@JayJay said in Mini 5 no heaters:
and : Duet3_SDiap32_Mini5plus.bin
rename the old Duet3_SDiap_Mini5plus.bin to old
and copy another version of Duet3_SDiap32_Mini5plus.bin and remove the 32 and try the firmware update again. -
that cured all thank you.
but i want to know why the bed didnt work on out2 ? as with an SSR it should have been fine
-
maybe a bad crimp job?
-
nah my job is an auto electrician the crimps were fine i checked continuity with a meter too.
-
@JayJay said in Mini 5 no heaters:
that cured all thank you.
but i want to know why the bed didnt work on out2 ? as with an SSR it should have been fine
Yes it should have worked, provided that the fuse for the heaters/motors/fans is intact (the bed heater uses a separate fuse).
- Did the red LED next to OUT2 light when you tried to turn on the bed heater?
- Did you try running M98 P"config.g" to check for errors in the config,g file?
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
@dc42 said in Mini 5 no heaters:
@JayJay said in Mini 5 no heaters:
that cured all thank you.
but i want to know why the bed didnt work on out2 ? as with an SSR it should have been fine
Yes it should have worked, provided that the fuse for the heaters/motors/fans is intact (the bed heater uses a separate fuse).
- Did the red LED next to OUT2 light when you tried to turn on the bed heater?
- Did you try running M98 P"config.g" to check for errors in the config,g file?
The fuses are all intact.
I cant remember if the LED turned on or not, since i moved it to out0 and it worked i left it alone.
M98 reports
M98 P"config.g" HTTP is enabled on port 80 FTP is disabled TELNET is disabledbut i am now encountering an issue with getting the probe to be recognised during G32
