Mini 5 no heaters

Veti

can you post the M122 of both the mini and the toolboard. maybe there is a can communication problem.

JayJay

can you post the M122 of both the mini and the toolboard. maybe there is a can communication problem.

i also tried moving the thermistor to temp0 and that shows as n/a also

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.2-beta3.2+1 running on Duet 3 Mini5plus WiFi (standalone mode)
Used output buffers: 3 of 40 (11 max)
=== RTOS ===
Static ram: 97472
Dynamic ram: 132764 of which 368 recycled
Never used RAM 30516, free system stack 176 words
Tasks: NETWORK(ready,168) HEAT(blocked,195) CanReceiv(blocked,875) CanSender(blocked,371) CanClock(blocked,370) TMC(blocked,56) MAIN(running,448) IDLE(ready,20) AIN(blocked,258)
Owned mutexes:
=== Platform ===
Last reset 00:03:29 ago, cause: software
Last software reset at 2020-12-29 14:51, reason: User, GCodes spinning, available RAM 30516, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0x00
Supply voltage: min 0.0, current 23.6, max 23.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0
Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0
Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0
Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 39, reads 29883, writes 9, timeouts 0, DMA errors 0
Driver 5: position 0, assumed not present
Driver 6: position 0, assumed not present
Date/time: 2020-12-29 14:55:14
Slowest loop: 10.22ms; fastest: 0.12ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 3.3ms, write time 4.7ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 26.88ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25beta0
WiFi MAC address f4:cf:a2:6f:bd:af
WiFi Vcc 3.38, reset reason Power up
WiFi flash size 2097152, free heap 26680
WiFi IP address 192.168.0.115
WiFi signal strength -48dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 0, send timeouts 0, longest wait 2ms for type 6049, free CAN buffers 15

M122 B121
Diagnostics for board 121:
Duet TOOL1LC firmware version 3.2-RC2 (2020-12-24)
Bootloader ID: not available
Never used RAM 4176, free system stack 96 words
HEAT 90 CanAsync 89 CanRecv 83 TMC 54 MAIN 324 AIN 64
Last reset 00:05:42 ago, cause: software
Last software reset data not available
Driver 0: position 0, 80.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 51, reads 39933, writes 10, timeouts 0, DMA errors 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.0V
MCU temperature: min 32.2C, current 32.6C, max 32.6C
Ticks since heat task active 61, ADC conversions started 342054, completed 342053, timed out 0
Last sensors broadcast 0x00000000 found 0 64 ticks ago, loop time 0
CAN messages queued 2765, send timeouts 0, received 3098, lost 0, free buffers 36

Veti

@JayJay said in Mini 5 no heaters:

RepRapFirmware for Duet 3 Mini 5+ version 3.2-beta3.2+1

you did not do the update to 3.2-RC2

after the update power the entire system down and up again

JayJay

@Veti said in Mini 5 no heaters:

@JayJay said in Mini 5 no heaters:

RepRapFirmware for Duet 3 Mini 5+ version 3.2-beta3.2+1

you did not do the update to 3.2-RC2

after the update power the entire system down and up again

hmmm i dont know why it is saying that as i definately downloaded the rc2 candidate from github

i uploaded it to the board and it asked me if i wantted to update which i did.

i think the correct file is : Duet3Firmware_Mini5plus.uf2
and : Duet3_SDiap32_Mini5plus.bin

Veti

@JayJay said in Mini 5 no heaters:

and : Duet3_SDiap32_Mini5plus.bin

rename the old Duet3_SDiap_Mini5plus.bin to old
and copy another version of Duet3_SDiap32_Mini5plus.bin and remove the 32 and try the firmware update again.

JayJay

that cured all thank you.

but i want to know why the bed didnt work on out2 ? as with an SSR it should have been fine

Veti

@JayJay

maybe a bad crimp job?

JayJay

@Veti

nah my job is an auto electrician the crimps were fine i checked continuity with a meter too.

dc42

@JayJay said in Mini 5 no heaters:

that cured all thank you.

but i want to know why the bed didnt work on out2 ? as with an SSR it should have been fine

Yes it should have worked, provided that the fuse for the heaters/motors/fans is intact (the bed heater uses a separate fuse).

Did the red LED next to OUT2 light when you tried to turn on the bed heater?
Did you try running M98 P"config.g" to check for errors in the config,g file?

JayJay

@dc42 said in Mini 5 no heaters:

@JayJay said in Mini 5 no heaters:

that cured all thank you.

but i want to know why the bed didnt work on out2 ? as with an SSR it should have been fine

Yes it should have worked, provided that the fuse for the heaters/motors/fans is intact (the bed heater uses a separate fuse).

Did the red LED next to OUT2 light when you tried to turn on the bed heater?

Did you try running M98 P"config.g" to check for errors in the config,g file?

The fuses are all intact.

I cant remember if the LED turned on or not, since i moved it to out0 and it worked i left it alone.

M98 reports

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

but i am now encountering an issue with getting the probe to be recognised during G32