Thanks!

You could use some CSS to make it floating in the bottom right corner of the browser and increase its size a little that way it is usable regardless of how far down you are

Indeed, or replace the forum with a better version 😄

No offence taken. The point I was making is that an object in motion will maintain it's speed without any additional force being applied. In the case of an orbiting satellite, gravity and centrifugal forces balance each other out so it maintains it's orbit. Or in the case of an elliptical orbit, there can be two or more gravitational forces being applied, so the forces acting on it vary. The same principal applies though - that is to say, it will maintain it's motion, whether that be in straight line, circular or elliptical, without any additional force being applied and it takes very little force to move it slightly, but a great deal more force to accelerate the object out orbit.

Nothing I can think of.

I may tinker with this idea in OpenSCAD.

Something like a small triangular carriage with three arms around the points of the triangle using a mag-ball setup.

It's adding 1/3 more weight, but maybe it would make the effector more stable at higher speeds?

Why can you not rename the file extension in windows? (If it's because you can not see the extension, you can change that – depending on your version of windows it will be found in different places, but the "folder options" settings are what you are looking for.)

Makes sense, I will check and let you know 🙂

Thanks!

Thanks. Maybe I can figure out how to have it turn itself off.

I like the simplicity and hence quick loading of this forum. KISS is my vote.

Agreed, as usual most celebration dates in america have nothing to do with the actual event. Thanksgiving is a prime example, its date was changed a dozen times throughout history in order to improve chirstmas sales to boost the economy. The actual date has nothing to do with what is being celebrated.

The second one with tools numbered from 0 should work. However, currently PanelDue only reads the tool configuration once when it first connects. So you will have to power it down and up again or press the Reset button on PanelDue to pick up the new tool numbering.

Reading your link i want to do some experimentation. I know what they are addressing has to do with deltas but i, at some point in the past read about a bug in Simplify3D that was overcome by changing layer height to 2.0001

Even though i have a cartesan i want to see if theres any difference between changing the points where steps vs microsteps land on the layers

Along these lines I wondered if it was possible to echo to the DWC console any commands sent by the user so that there is a log of what was sent? I appreciate you don't want the full gcode file of a print scrolling down the console.

When I change temperature I see the G10 xx xxx command appear in the console, but it would be nice if all manual commands were listed, such as move axis, or run macro etc.. Even if they are sent from a host like pronterface.

Just a thought.

Also any progress on having the last few commands stored for recall in DWC on the console, like pronterface does or DOS or whatever so you can press up/down arrows and resend a command you typed previously, I only ask as this is a standard feature of nearly all console interfaces, its absence from DWC is noticeable.

Sweet. Thanks 🙂

1 board at 1.18 and the other 2 at 1.19beta8. That did the trick. Thank you!!!

This is one for chrishamm.

See the note at the end of this section: https://duet3d.com/wiki/Connecting_and_configuring_fans#G-code_controlled_fans.

I don't know mate, seems like 6 to one half a dozen to the other.

Mine heats both bed and extruder to full temp before printing, and yes it does go to the center twice…once after initial homing and then again after mesh bed leveling to reset the nozzle height, but I see no real harm in it.

I don't use any pressure advance, do you have a bowden extruder?

I do like how to use 170 degC extruder temp before print start to avoid oozing (which is a pain in the arse), but I want my bed at full temp before probing.

Just goes to show how many options are available for us to use, and I'm thinking some of your script blended with mine might be good for my application.

ty so much. ill check it out hopefully get it going good soon