Posts made by westech

@jay_s_uk Thanks will do.

@jay_s_uk Hi Jay!!! Its a Mellow FLY RRF E3 V1.0 (I have several of you boards:-)

DWC 3.5.2,

STMWIFI 3.3.0_14

Duet Wifi Server 1.26-05S-D

Endcap 96.5 v101.5 1.2mm.gcode

@dc42 Yes, I printed three versions. Like I said it printed fine. I double checked my start GCODE from Cura and no M110. Not a big deal since it prints. Just curious what Cura was trying to execute that Duet didn't like.

So no worries:-)

Greetings!

I sliced from Cura 2.8. It printed fine but the console gave me this error at the start : Error: Bad command: -1 M110.M110 is not in my start or end Gcode. So not sure were in Cura I can turn it off? Any idea what it is trying to do?

Weird, I just did a search of the gcode in GCODE ANALYZER, and M110 can't be found?

Thanks

Max

@MJLew Thanks, I remember this being solved a long time ago. Your suggestion is familiar. I just thought I might look at old non retracting gcode I've printed.

Greetings!

I remember this issue a long time ago. I'm using Cura. Below is my standard end g-code. I know one of the commands is not compatible with Suet. After the print completes it completely retracts the filament out of the extruder. If you don't notice, you will start the next print but no filament. What could I change or remove. Thanks

Max

G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-2 Z0.2 F2400 ;Retract and raise Z
G1 X5 Y5 F3000 ;Wipe out
G1 Z10 ;Raise Z more
G90 ;Absolute positioning

G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed

M84 X Y E ;Disable all steppers but Z

@westech Thanks Jay, Everything is working. I have both duets onliner and my klipper. All by hostnames.

I think there was a problem on the DUET. Like I said sometimes it will show up as "Duet-WiFi" and some time by the printer name.

My second Duet is a Mellow Fly E3 V1.1. It always comes up as "enderfly" never "Duet-WiFi."

@jay_s_uk said in Help accessing Duet with hostname rather than IP address:

@westech I would suggest upgrading to 3.4.5+_107 https://github.com/gloomyandy/RepRapFirmware/releases/tag/v3.4.5%2B_107
and wifi firmware 1.27_02 https://github.com/gloomyandy/DuetWiFiSocketServer/releases/tag/v1.27-02
then let us know how you get on.
If your printer name is Printer1 then http://Printer1.local "should" work

Thanks, Sometimes when I see the printer on the network it says "Duet-Wifi" sometimes it will say "Printer1" That's with a netwotk scanner.

@OwenD Thanks I will check that out. Like I said I can access a raspberry pi running Klipper at http://octopi

And I verified I have bonjoir installed.

Thanks.

@jay_s_uk said in Help accessing Duet with hostname rather than IP address:

M122

Hi Jay!

You've helped me alot over on your Discord, thanks. This one is a CDYv3. One extra question. I'm running 3.4.0 Is there any thing special for me to upgrade to 3.5 firmware? I don't have any LEDs or Canbus stuff. This is just an ender 3. Thanks:-)

M122
=== Diagnostics ===
RepRapFirmware for STM32F4 based Boards (fly_cdyv3) version 3.4.0_1 (2022-03-17 12:50:35) running on STM32F4
Used output buffers: 14 of 40 (38 max)
=== RTOS ===
Static ram: 21344
Dynamic ram: 75952 of which 44 recycled
Never used RAM 32704, free system stack 214 words
CCMRam static ram: 15868 dynamic ram: 19852 free ram 29812
Tasks: NETWORK(ready,9.8%,231) HEAT(notifyWait,0.0%,347) Move(notifyWait,0.0%,361) FSWRITE(notifyWait,0.0%,566) MAIN(running,88.6%,452) IDLE(ready,1.6%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:47 ago, cause: [power on/off]
Last software reset at 2023-06-14 09:37, reason: User, GCodes spinning, available RAM 32496, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.9, current 30.5, max 30.7
Supply voltage: min 24.0, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill 2209, SG min 0, reads 3265, writes 11
Driver 1: standstill 2209, SG min 0, reads 3265, writes 11
Driver 2: standstill 2209, SG min 0, reads 3264, writes 11
Driver 3: standstill 2209, SG min 0, reads 3263, writes 12
Driver 4: standstill 2209, SG min 0, reads 3264, writes 11
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Date/time: 2023-06-15 22:48:01
Slowest loop: 2.72ms; fastest: 0.09ms
=== Storage ===
Free file entries: 10
SD card 0 detected
SD card longest read time 29.7ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0, chamber heaters -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 35.18ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(2) HTTP(0) HTTP(0)
HTTP sessions: 1 of 8
Uploads/Errors: 0/0
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
Bad header: 0/0
WiFi firmware version 1.26-08S32-D
WiFi MAC address 0a:4f:66:a8:cf:82
WiFi Vcc 0.00, reset reason Power up
WiFi flash size 0, free heap 143268
WiFi IP address 192.168.55.175
WiFi signal strength -54dBm, mode 802.11n, reconnections 0, sleep mode none
Clock register 00000000
Socket states: 2 4 0 0 0 0 0 0

Greetings!

This should be simple but I can't seem to get it working.

My wifi keeps changing the assigned IP for my 2 Duet printers. I would like to use hostname instead in chrome.

My Duet is called Printer1 (M550 RepRap name: Printer1)

But a network scanner shows it as Duet-WiFi IP Address 192.196.45.123/24

I can access it with the IP but not with the hostname? I'm on Windows 10. I checked and I do have bonjour running.

I can access another printer via http://octopi so it is resolving the name.

I have tried:
http://Duet-WiFi
http://Printer1
http://Duet-WiFi.local
http://Printer1.local

No luck so far. Like I said I'm accessing it via the IP no problem, and bonjour is running.

Thanks.

Max

@Phaedrux said in Trouble changing Wifi user/pass How to delete old SSID?:

M552 S1

Yes: M552 S1 in config

My printer worked great on my old WIFI.

It is running now (old wifi), But I need to switch to a new wifi. My new Wifi shows up under M587.

Say the old wifi is off, will Duet just look for the next Wifi? There are three Wifis reported under M587.

I was hoping to delete the old wifis to keep things clean.

Thanks

Max

Greetings!

So i followed some instructions.

put it into idle mode by sending command M552 S0

M587 S"Mxxxxxxx" P"Pxxxxxxxx"

But when I restart it does not connect.

M587

Remembered networks: Shows the old and new wifi.

How can i delete the old wifi user/pass?

My wifi is my phone. And I see it changes the IP each time: example 192.168.60.175,,, next time it may be 192.168.75.175.

Say my printer name is BOB

I tried using local.BOB but it dis not connect?

The SSID is on the ESP32 so I can't just edit the config like a pi? Supplicant file? Thanks

Max

I tried a 1mm nozzle for Vase mode in Cura and I did not get layers that bonded. When I tried Prusa in Vase mode it did make a manifold vase. Nut that was awhile ago under Marlin.

I really don't understand all the settings. So sometimes messing with them makes things worse.:-)

@o_lampe I have 3 Ender 3s, that print exceptionally well. These STLs I need to print have threads. The profiles I use are not cutting it. I was going to try Prusa or even Simplify 3D. I don't believe its a hardware issue, but a profile issue. I have been playing with Horizontal Expansion as well as Slicing Tolerances.

Greetings!

I've mainly been a Cura user. I have some STLs I need to print with good fit tolerances. I'm not having great luck. Some large threads. So I wanted to try PrusaSlicer and IdeaMaker.

So, I'm happily running my Duet on an Ender 3. I've been googling how to configure both for Reprap. Have not found anything very clear. In Cura there is a dropdown for RepRap.

For some reason in Prusa it will start printing but nothing extrudes and I get an error a tool was not selected.

With Cura I remember I had to change my End G-Code or the filament would completely retract.

End G-Code:

G91 ;Relative positioning
M83 ;Relative extruder mode
G1 E-2 F2700 ;Retract a bit
G1 E-2 Z0.2 F2400 ;Retract and raise Z
G1 X5 Y5 F3000 ;Wipe out
G1 Z10 ;Raise Z more
G90 ;Absolute positioning
;M82 ;set extruder absolute mode

G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed

M84 X Y E ;Disable all steppers but Z

---

So big question, anyone using Prusaslicer or Ideamaker successfully? Any advice on setting it up for Duet? Or maybe share a profile.

Thanks

Max

@deckingman Wow, thank you.

@phaedrux I would like a physical button to preheat the nozzle for filament change, without having to use the web UI. On Youtube Chris Riley did a marlin centric video on how to set-up physical buttons.

The Z max pin was recommended to me as the easiest pin to use. I was told to avoid the X and Y max pins for some reason.

So, I can physically wire the switch. I'm just not 100% clear how much I need to add to my Config to get it to work.

Can the whole process be included in the printer config file, or should I have the actual nozzle heating up in a macro?

I know I need an M950 to set up the pin as a switch, but not sure of the details.

Then to heat the nozzle I'd need M109 S215 to set the nozzle to 215c.

I'm just not clear if I'm missing anything.

Thanks.

Max

Greetings!

I realize I need to add the ZMAX pins in Config, and I'm guessing I need a separate Macro file, that will trigger the nozzle to heat up. I'd like it only to run if it isn't printing.

So there would be an M950 in main config under endstops. I'm not sure of the specific options. Would that point to a preheat macro? What Then I'd need M109 S215 to heat the extruder? Can that be in the printer config, or separate file.

Thanks.