@westech Thanks Jay, Everything is working. I have both duets onliner and my klipper. All by hostnames.
I think there was a problem on the DUET. Like I said sometimes it will show up as "Duet-WiFi" and some time by the printer name.
My second Duet is a Mellow Fly E3 V1.1. It always comes up as "enderfly" never "Duet-WiFi."
@phaedrux Thanks, I think I got it.
What didn't work:
homeall.g
If I changed G92 Z1.4 as a positive number it would respect that in the console. Displaying Z1.4
But I needed a negative number. G92 Z-1.4 was not respected. and would show it as Z0 in the console.
What worked was adding:
G1 Z1.4 F100
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
I am printing now and by triggering the endstop then Raising the Z Then G92 Z0. worked.
I really like how RRF can be adjusted so easily. I'm not going to miss going into Platform.io and recompiling Marlin everytime I have change a little thing.
Next stop the BL touch. But I know now how to adjust the Z for different bed heights.
Thanks.
@fcwilt Good info. On my Marlin Ender 3 with a mirror. It is perfectly trammed and I haven't had to do any adjusting. Even though it also has a BL Touch, I don't usually use it because I get such consistent prints.
I print mainly small prototype parts I design in Fusion, so I don't usually use the whole bed.
i mainly got the Textured PEI bed for making nice face surfaces for project enclosures. The steel plate (Energetic) is far from being as flat as my Mirror.
I will look into the G30. I have the RRF G-code "dictionary" always open on my screen:-)
Thank you!
@jay_s_uk Hi Jay!!! Its a Mellow FLY RRF E3 V1.0 (I have several of you boards:-)
DWC 3.5.2,
STMWIFI 3.3.0_14
Duet Wifi Server 1.26-05S-D
@dc42 Yes, I printed three versions. Like I said it printed fine. I double checked my start GCODE from Cura and no M110. Not a big deal since it prints. Just curious what Cura was trying to execute that Duet didn't like.
So no worries:-)
Greetings!
I sliced from Cura 2.8. It printed fine but the console gave me this error at the start : Error: Bad command: -1 M110.M110 is not in my start or end Gcode. So not sure were in Cura I can turn it off? Any idea what it is trying to do?
Weird, I just did a search of the gcode in GCODE ANALYZER, and M110 can't be found?
Thanks
Max
@MJLew Thanks, I remember this being solved a long time ago. Your suggestion is familiar. I just thought I might look at old non retracting gcode I've printed.
Greetings!
I remember this issue a long time ago. I'm using Cura. Below is my standard end g-code. I know one of the commands is not compatible with Suet. After the print completes it completely retracts the filament out of the extruder. If you don't notice, you will start the next print but no filament. What could I change or remove. Thanks
Max
G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-2 Z0.2 F2400 ;Retract and raise Z
G1 X5 Y5 F3000 ;Wipe out
G1 Z10 ;Raise Z more
G90 ;Absolute positioning
G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed
M84 X Y E ;Disable all steppers but Z
@westech Thanks Jay, Everything is working. I have both duets onliner and my klipper. All by hostnames.
I think there was a problem on the DUET. Like I said sometimes it will show up as "Duet-WiFi" and some time by the printer name.
My second Duet is a Mellow Fly E3 V1.1. It always comes up as "enderfly" never "Duet-WiFi."
@jay_s_uk said in Help accessing Duet with hostname rather than IP address:
@westech I would suggest upgrading to 3.4.5+_107 https://github.com/gloomyandy/RepRapFirmware/releases/tag/v3.4.5%2B_107
and wifi firmware 1.27_02 https://github.com/gloomyandy/DuetWiFiSocketServer/releases/tag/v1.27-02
then let us know how you get on.
If your printer name isPrinter1thenhttp://Printer1.local"should" work
Thanks, Sometimes when I see the printer on the network it says "Duet-Wifi" sometimes it will say "Printer1" That's with a netwotk scanner.
@OwenD Thanks I will check that out. Like I said I can access a raspberry pi running Klipper at http://octopi
And I verified I have bonjoir installed.
Thanks.
@jay_s_uk said in Help accessing Duet with hostname rather than IP address:
M122
Hi Jay!
You've helped me alot over on your Discord, thanks. This one is a CDYv3. One extra question. I'm running 3.4.0 Is there any thing special for me to upgrade to 3.5 firmware? I don't have any LEDs or Canbus stuff. This is just an ender 3. Thanks:-)
M122
=== Diagnostics ===
RepRapFirmware for STM32F4 based Boards (fly_cdyv3) version 3.4.0_1 (2022-03-17 12:50:35) running on STM32F4
Used output buffers: 14 of 40 (38 max)
=== RTOS ===
Static ram: 21344
Dynamic ram: 75952 of which 44 recycled
Never used RAM 32704, free system stack 214 words
CCMRam static ram: 15868 dynamic ram: 19852 free ram 29812
Tasks: NETWORK(ready,9.8%,231) HEAT(notifyWait,0.0%,347) Move(notifyWait,0.0%,361) FSWRITE(notifyWait,0.0%,566) MAIN(running,88.6%,452) IDLE(ready,1.6%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:47 ago, cause: [power on/off]
Last software reset at 2023-06-14 09:37, reason: User, GCodes spinning, available RAM 32496, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 22.9, current 30.5, max 30.7
Supply voltage: min 24.0, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill 2209, SG min 0, reads 3265, writes 11
Driver 1: standstill 2209, SG min 0, reads 3265, writes 11
Driver 2: standstill 2209, SG min 0, reads 3264, writes 11
Driver 3: standstill 2209, SG min 0, reads 3263, writes 12
Driver 4: standstill 2209, SG min 0, reads 3264, writes 11
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Date/time: 2023-06-15 22:48:01
Slowest loop: 2.72ms; fastest: 0.09ms
=== Storage ===
Free file entries: 10
SD card 0 detected
SD card longest read time 29.7ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0, chamber heaters -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 35.18ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(2) HTTP(0) HTTP(0)
HTTP sessions: 1 of 8
Uploads/Errors: 0/0
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
Bad header: 0/0
WiFi firmware version 1.26-08S32-D
WiFi MAC address 0a:4f:66:a8:cf:82
WiFi Vcc 0.00, reset reason Power up
WiFi flash size 0, free heap 143268
WiFi IP address 192.168.55.175
WiFi signal strength -54dBm, mode 802.11n, reconnections 0, sleep mode none
Clock register 00000000
Socket states: 2 4 0 0 0 0 0 0