I came here with 0 knowledge about control systems and you guys made my journey of converting my Creality K1 printer possible. I don't think that I would be able to do it on my own without your help. So as a thank you I just want to share my config files that could maybe be helpful for someone who might find himself in a similar situation like I was few months ago.

I run the factory setup of the printer, only thing I have removed were the load cells on the printer used for homing the machine and I run an IR Z-probe instead.

Config and homing files:
homeall.g config.g homez.g homey.g homex.g

Some prints I am getting with the duet controler.

You can also check how it is pritning here:
https://www.youtube.com/shorts/4Fwqjc0oUp0

@droftarts Thanks for the guidance. Thats unfortunate that no one has done it yet, but once I manage to convert my machine I will share it with you so other people can use the configuration without the hustle.

I came here with 0 knowledge about control systems and you guys made my journey of converting my Creality K1 printer possible. I don't think that I would be able to do it on my own without your help. So as a thank you I just want to share my config files that could maybe be helpful for someone who might find himself in a similar situation like I was few months ago.

I run the factory setup of the printer, only thing I have removed were the load cells on the printer used for homing the machine and I run an IR Z-probe instead.

Config and homing files:
homeall.g config.g homez.g homey.g homex.g

Some prints I am getting with the duet controler.

You can also check how it is pritning here:
https://www.youtube.com/shorts/4Fwqjc0oUp0

I have noticed new way of scanning the bed scanner measuring the eddy current to achieve faster and more precise auto bed leveling. I have found 2 companies making such sensors - Beacon and BigTreeTech. They both state that these scanners are meant for Klipper but I would be interested to use it on Duet. Would that work?

What pins on 6HC can I use to control 3 230 V heater? Or do I need an extension board?

Info about the heaters:

Each heater has its own solid state relay.

Top heater, 500 Watts, 5A for 120VAC and 2.5A for 240VAC systems
Middle heater, 350 Watts, 3.5A for 120VAC and 1.75A for 240VAC systems
Nozzle heater, 250 Watts, 2.5A for 120VAC and 1.25A for 240VAC systems
Many pins can be used as the temperature output control. Your 3D Printer Controller (or motion controller) pins can be as below:

The standard extruder output (E0, E1, E2, etc). These are usually rated at the same voltage as your main power supply (12VDC or 24VDC).
Any available expansion pins. These can be determined by checking the 3D Printer Controller specification pins.

Hi I need to select a z probe for the printer in our company. We are building a 1x1x1m printer using pellet extruder instead of classical fillament extruder. I want to create a mesh of the bed but I am unsure what z probe would be suitable for this application.
I dont think that mechanical probes like BLTouch would have sufficient reach of the probe - required reach would be aroud 2-3 centimeters. Material of the printing surface is yet unknown.
What z probes would be good for this application and compatible with Duet hardware (MB6HC)?

I noticed a header in the docs of calibrating the printer which points to the optimal slicer settings. Why is there nothing to see? I would be interested in seeing the setting for PrusaSlicer
https://docs.duet3d.com/en/How_to_guides/Calibration

@jay_s_uk Awesome. Thank you very much for quick and great help. You can mark this topic as solved.

@jay_s_uk It finally stopped, but I wasnt paying attention. What exactly does the tuning do? I checked the config.g file thinking that it would modify the heaters parameters, but nothing has changed.

@jay_s_uk How long should the tuning last? Mine is running for over an hour now and for the past 30 minutes have been looping. It goes to 61.3 degrees C, then cools down to 55 and then again.

@jay_s_uk Omg, you are right. Now it works but I still get this error. How can I fix it?

Can you please help me debug what might be the issue when my heating bed is not heating? When I send the M140 S55 command it activates the bed heater but the current temperature does not change and then it gives an error (as in the image). I cannot acces the bed thermistor, but I believe that it works well, because it shows the same room temperature as my chamber thermistor.

Config.g

; Configuration file for RepRapFirmware on Duet 3 Main Board 6HC
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.0 on Mon May 27 2024 12:24:16 GMT+0200 (Central European Summer Time)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"Duet 3" ; set hostname

; Network
M552 P192.168.2.1 S1 ; configure Ethernet adapter
M553 P255.255.255.0
M586 P0 S1 ; configure HTTP

; Smart Drivers
M569 P0.0 S0 D2 ; driver 0.0 goes forwards (X axis)
M569 P0.1 S0 D2 ; driver 0.1 goes forwards (Y axis)
M569 P0.2 S0 D2 ; driver 0.2 goes forwards (Z axis)
M569 P0.3 S1 D2 ; driver 0.3 goes forwards (extruder 0)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes
M584 X0.0 Y0.1 Z0.2 ; set axis mapping
M350 X32 Y32 Z16 I1 ; configure microstepping with interpolation
M906 X800 Y800 Z800 ; set axis driver currents
M92 X88.8 Y88.8 Z1280 ; configure steps per mm
M208 X-5:229 Y-5:229 Z-5:255 ; set minimum and maximum axis limits

; Axes - Testing
M566 X1200 Y1200 Z100 ; set maximum instantaneous speed changes (mm/min)
M203 X4800 Y4800 Z300 ; set maximum speeds (mm/min)
M201 X2000 Y2000 Z100 ; set accelerations (mm/s^2)

; Axes - What should be
;M566 X12000 Y12000 Z300 ; set maximum instantaneous speed changes (mm/min)
;M203 X48000 Y48000 Z1200 ; set maximum speeds (mm/min)
;M201 X20000 Y20000 Z300 ; set accelerations (mm/s^2)

; Extruders
M584 E0.3 ; set extruder mapping
M350 E16 I1 ; configure microstepping with interpolation
M906 E550 ; set extruder driver currents
M92 E420 ; configure steps per mm
M566 E120 ; set maximum instantaneous speed changes (mm/min)
M203 E28800 ; set maximum speeds (mm/min)
M201 E250 ; set accelerations (mm/s^2)

; Kinematics
M669 K1 ; configure CoreXY kinematics

; Endstops
M574 X1 S3; configure X axis endstop X2 means axis high end S3 stands for sensorless
M574 Y1 S3 ; configure Y axis endstop Y1 means axis low end - jesli tam bude 0 nebo max hodnota
M574 Z1 S1 P"!io0.in" ; configure sensorless Z axis endstop at high end 
; Kdyz to pri pouziti snimace nejede vubec znamena to ze je potreba invertnout snimac pouzitim - P"!...
M915 X S1 R0 F0 ; sensitivity is set up here
M915 Y S1 R0 F0 ; sensitivity is set up here
; M915 Z S1 R0 F0 ; Configure motor stall detection for sensorless homing

; Sensors
M308 S0 P"temp0" Y"thermistor" A"Heated Bed" T100000 B4036 C7.725999999999999e-8 ; configure sensor #0
M308 S1 P"temp1" Y"thermistor" A"Nozzle" T100000 B4036 C7.725999999999999e-8 ; configure sensor #1
M308 S2 P"temp2" Y"thermistor" A"Chamber" T100000 B4036 C7.725999999999999e-8 ; configure sensor #2

; Heaters
M950 H0 C"out0" T0 ; create heater #0
M143 H0 P0 T0 C0 S115 A0 ; configure heater monitor #0 for heater #0
M307 H0 R2.43 D5.5 E1.35 K0.56 B1 ; configure model of heater #0
M950 H1 C"out1" T1 ; create heater #1
M143 H1 P0 T1 C0 S300 A0 ; configure heater monitor #0 for heater #1
M307 H1 R2.43 D5.5 E1.35 K0.56 B0 ; configure model of heater #1

; Heated beds
M140 P0 H0 ; configure heated bed #0

; Fans
M950 F0 C"out3" ; create fan #0
M106 P0 S0 L0 X1 B0.1 ; configure fan #0

M950 F1 C"out4" ; create fan #1
M106 P1 S0 B0.1 H1 T45 ; configure fan #1

M950 F2 C"out7" ; create fan #2 / back fan
M106 P2 S0 

; Tools
M563 P0 D0 H1 F0 ; create tool #0
M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C