Topics created by printthatthing

@o_lampe pro-tip CTRL - F 🙂

@dc42 said in Expantion port logic output:

M950 P0 C"spi.cs5"

Thank you, I got it to work now:)
P5 was the next free so my config file now have these lines to start logic 0
M950 P5 C"spi.cs5"
M42 P5 S0

My layer change script in Simplyfy3d as below.
G1 X395 Y200 F15000
G4 S0
G4 P500
M42 P5 S1
G4 P200
M42 P5 S0
G4 P500

@Phaedrux Works like a charm, thank you so much. I totally missed that line.

@Phaedrux said in RRF Config Mapping:

@printthatthing said in RRF Config Mapping:

Update:
My bad, it might be M303 H0 S90

😑 Yes of course.

Now it works fine:) Thank you so much for all support.

I think I solved it by reflash it by usb and hopefully evrything looks okay for 3.1.1 now.
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Used output buffers: 3 of 24 (15 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93888 of which 44 recycled
Exception stack ram used: 284
Never used ram: 8876
Tasks: NETWORK(ready,384) HEAT(blocked,880) MAIN(running,1912) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:05:26 ago, cause: software
Last software reset at 2020-03-21 18:43, reason: User, spinning module GCodes, available RAM 9980 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 32.3, current 32.5, max 32.8
Supply voltage: min 1.6, current 1.6, max 1.7, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 2020-07-05 16:08:33
Cache data hit count 579235577
Slowest loop: 5.95ms; fastest: 0.09ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 200.80ms; fastest: 0.08ms
Responder states: HTTP(2) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8

WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 1
WiFi firmware version 1.23
WiFi MAC address bc:dd:c2:33:b9:4b
WiFi Vcc 3.29, reset reason Unknown
WiFi flash size 4194304, free heap 23704
WiFi IP address 192.168.2.20
WiFi signal strength -46dBm, reconnections 0, sleep mode modem
Socket states: 2 2 0 0 0 0 0 0