@dc42 ; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Mon Oct 15 2018 11:27:10 GMT-0500 (Central Daylight Time)
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
; Network
M550 PNamDuetTest ; Set machine name
M551 PTest123 ; Set password
M552 S1 ; Enable network
M587 S"Print Print" P"Nam123123" I192.168.2.100 ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
; Drives
;M569 P0 S1 ; Drive 0 goes forwards
;M569 P1 S1 ; Drive 1 goes forwards
;M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M569 P5 S1 T5 ; Drive 5 goes forwards
M569 P6 S1 T5 ; Drive 6 goes forwards
M569 P7 S1 T5 ; Drive 7 goes forwards
M569 P8 S1 T5 ; Drive 8 goes forwards
M584 X5 Y6:7 Z8 E3 ; Apply custom drive mapping
M350 X32 Y32 Z32 I0 ; Configure microstepping without interpolation
M350 E16 I1 ; microstep with interpolation
M92 X218.73852 Y218.73852 Z1259.84252 E418.5; Set steps per mm
M566 X900 Y900:900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000:12000 Z180 E1200 ; Set maximum speeds (mm/min)
M201 X500 Y500:500 Z250 E250 ; Set accelerations (mm/s^2)
M906 X1600 Y1600:1600 Z1600 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X1200 Y800 Z150 S0 ; Set axis maxima
; Endstops
M574 X1 Y1 Z2 S0 ; Set active high endstops
; Z-Probe
M558 P1 H10 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X400 Y400 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X30:1170 Y30:770 S20 ; Define mesh grid
; Heaters
M140 H-1 ; Disable heated bed
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
;M305 P2 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
;M143 H2 S280 ; Set temperature limit for heater 1 to 280C
; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 ; Define tool 0
M563 P1 D1 H2 ; Define tool 1
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
G10 P1 X100 Y0 Z0 ; Set tool 0 axis offsets
G10 P1 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
; Automatic saving after power loss is not enabled
; Custom settings are not configured