Topics created by moo16

@moo16 said in FAN allocating fault- attach fan to tool:

; Fans M950 F0 C"fan0" Q100 ; create fan 0 on pin fan0 and set its frequency M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off M950 F2 C"fan2" Q2500 ; create fan 2 on pin fan2 and set its frequency M106 P2 S1 H-1 ; set fan 2 value. Thermostatic control is turned off

This should be fine, but S1 means the fans are turned on by default. Use S0 to have them off to start with.

M106 P0 S1 should turn the first fan on.

@moo16 said in FAN allocating fault- attach fan to tool:

M98 respones: MACRO 3 NOT FOUND

That doesn't make much sense to me.

Can you show a video or pictures of what you're trying to do on your screen?

@moo16

i am about to do the same. i was wondering if you have to drill new holes for the module. the wifi chip does not appear to have any pins. just soldered pads.

What exactly leads to an error message coming up?
What is the exact error message?

M350 X32 Y32 Z16:16 E16:16:16:16:16 I1 ; Configure microstepping with interpolation M92 X157.63 Y158.96 Z400:400 E115:320:115:305:320 ; Set steps per mm for extruders M566 X1200 Y700 Z24:24 E800:800:800:800:800 ; Set maximum instantaneous speed changes (mm/min) M203 X30000 Y30000 Z600:600 E15000:15000:15000:15000:15000 ; Set maximum speeds (mm/min) M201 X500 Y400 Z100:100 E600:600:600:600:600 ; Set accelerations (mm/s^2) M906 X800 Y800 Z800:800 E2500:1200:2500:1050:1200 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30

In this block you have 2 values defined for the Z axis. This is not supported. For each of those cases remove the second value for Z.

Z400:400 should just be Z400.

@moo16 said in Duet wi fi + duex 5 - drivers faults:

firmware version: RC-12 _3.0

Please update your firmware as well. First upload this zip file as is for 3.0 to the /sys folder in DWC and then again for 3.1.1.

https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/Duet2and3Firmware-3.0.zip

https://github.com/Duet3D/RepRapFirmware/releases/download/3.1.1/Duet2and3Firmware-3.1.1.zip

Once you have those things fixed, please post the results of M122

s

@Phaedrux
i will update today to the latest

Where and when was it purchased? Can you post photo of the damage?

@moo16 said in connectivity issue- DUET 3 main board 6hc:

firmware version: RC-12 _3.01

Please upgrade to firmware 3.1.1 and see of the problem persists.

@bearer said in DWC connection/ SD card disconnections:

M98 config.g

no errors.
only missing p parameter (m98 pconfig.g)
meanewhile im not sure what cause the disconnection. i downgrade the firmware version(all) again and it suddenly work well so far.
i saw post with the same problem and same not sure solution attach here:
https://forum.duet3d.com/topic/15714/dwc-connection-sd-card

it maybe in house network problem but with all my action im not sure which made it work.
thank you for advice i will improve my post techniques.
for now i close this thread.

https://forum.duet3d.com/topic/5909/guide-for-posting-requests-for-help

@moo16 said in stepper motor buzzing and not moving.:

,you can close it tnx

self service
https://forum.duet3d.com/topic/7773/forum-feature-mark-as-question-solved

note having to first mark it as a question, then solved.

@dc42 said in Heater LEDs always on- pic attach:

It's odd that 4 of the 5 heater LEDEs are on but the 5th is off. Possible causes are either two blown ICs (U9 and U10 on the DueX5) or problems in the config.g file.
Is either of those ICs getting hot?

those heaters were never in use,
im not using any heaters and disable heaters (with M140 H-1 ; no bed heater) still one day out of no ware they turned on the leds.
look like the heaters mosfet stucks on.
any suggestions? could it be back to normal somehow?

@moo16 said in Driver fault- repeat in 2 boards:

the problem appears only at extruders drives.

ok,
@dc42 @bearer
firstly, i closed all my open topics as you requested.
this problem(this post) probably was sourced with disconnecting and connecting the driver while current is applied to phases, i think it damage my drivers and finally damage the board.
another speculation is that the boards had been damaged by ARC that damage the boards and the drivers.
right now i have 1 main board with faulty drivers and 1 expansion with some faulty drivers(later become not responding at all).

i see it close issue. so i mark it as solved for now. appreciate your help
if you have any other ideas please share it with me.
thank you again

YES!
My bad!
it works....

thanks

@dc42 said in AC servo motor/driver control by Duet 3(MB6HC)- help:

and dir outputs should be good for 20mA each, and the Enable output for 10mA

hi,
back to be relevant again,
this board(1XD) is used for controlling steppers drivers/
what should i do if i need to control ac servo driver?
model and imformation- https://www3.panasonic.biz/ac/ae/motor/fa-motor/ac-servo/a6/index.jsp

appriciate your help

thank you for the help,
this fault solved by increasing Vin level + decrease motor current