Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. mickey30m
    3. Topics
    • Profile
    • Following 0
    • Followers 0
    • Topics 13
    • Posts 73
    • Best 1
    • Controversial 0
    • Groups 0

    Topics created by mickey30m

    • mickey30mundefined

      when print temp go to 0

      Duet Hardware and wiring
      • • • mickey30m
      8
      0
      Votes
      8
      Posts
      708
      Views

      timcurtis67undefined

      @mickey30m said in when print temp go to 0:

      @timcurtis67 hi

      my fan is connected to a pwm port. if i have it correct port 2.

      i can control it in dwc but he is always on, on a low output in the beginning, and when i move the slicer up in dwc he going to high flow.

      so i can control but i cannot get it off. this is not slicer related because in dwc is the problem also

      Try a different fan port to see if one of the mosfet's is bad. Don't forget to reconfigure for the new fan port.

    • mickey30mundefined

      upgrade my tornado with my duet

      Tuning and tweaking
      • • • mickey30m
      4
      0
      Votes
      4
      Posts
      678
      Views

      Phaedruxundefined

      @mickey30m Check this out

      https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Tool_change_files

    • mickey30mundefined

      Fan connectors dont work anymore

      Duet Hardware and wiring
      • • • mickey30m
      11
      0
      Votes
      11
      Posts
      1.2k
      Views

      mickey30mundefined

      @dc42 when i measure the volts. i get on the left connector. 0.00 and on the other connectors 0.15volt

      @dc42 an idea why?
      i dont see things that are damaged

    • mickey30mundefined

      Strange behavior from the z axis

      Duet Hardware and wiring
      • • • mickey30m
      9
      0
      Votes
      9
      Posts
      713
      Views

      mickey30mundefined

      @deckingman i Will post Them tommorow including a short video. And my settings.

      My first layer begins something like 2.1 because i have a z offset 1.9 but the exact thing that happend i Will post tommorow.

      As far i know i only change z offset. But i think that i make somewhere a misstake bacause this all happens so that's why i say i change z offset and something else.

      Many thanks for so far. I post tommorow.

    • mickey30mundefined

      New version of webinterface shows "?"

      Duet Hardware and wiring
      • • • mickey30m
      8
      0
      Votes
      8
      Posts
      745
      Views

      mickey30mundefined

      @zerspaner_gerd this works.
      i will learn myself to use it like this 😉

    • mickey30mundefined

      Laser on E1 dont work

      Duet Hardware and wiring
      • • • mickey30m
      16
      0
      Votes
      16
      Posts
      1.5k
      Views

      dc42undefined

      If you mean that you have connected the latser module power input directly to the E1 heater output, I don't recommend that. The laser module may not like having PWM applied to its power input.

    • mickey30mundefined

      Fan dont work anymore

      Duet Hardware and wiring
      • • • mickey30m
      2
      0
      Votes
      2
      Posts
      363
      Views

      dc42undefined

      If the fans don't work even when connected to the always-on fan connectors, then the fan voltage supply has fused. This happens if you short the two pins of one of the fan outputs together.

      To fix it:

      First check that you have the jumper in the correct position in the 3-pin fan voltage selector jumper block. If you have a version 1.03 or later Duet, check the 1A blade fuse visually or with a multimeter, and replace it if it has blown. If you have an older Duet, use a multimeter to check that there is continuity between the pin at the VIN end of the fan voltage selector jumper block, and the VIN+ terminal. if there is no continuity, then a via in the PCB trace between those pins has fused. You can bypass it using a piece of wire on the back of the PCB. There is another thread about this issue that includes a diagram. Before applying power again, check that you have resolved the short that caused the problem.
    • mickey30mundefined

      M500 dont work?

      Tuning and tweaking
      • • • mickey30m
      7
      0
      Votes
      7
      Posts
      905
      Views

      mickey30mundefined

      @dc42 many thanks, i think i get it now

    • mickey30mundefined

      Dual Z Endstops

      Duet Hardware and wiring
      • • • mickey30m
      3
      0
      Votes
      3
      Posts
      1.9k
      Views

      nraynaudundefined

      I found here on google, but the info is there:
      https://forum.duet3d.com/topic/860/dual-z-axis-endstops/14

    • mickey30mundefined

      S3d problem?

      General Discussion
      • • • mickey30m
      2
      0
      Votes
      2
      Posts
      465
      Views

      mickey30mundefined

      Added the photo of the print, the top wall is 0.99m from above 1 wall thick

    • mickey30mundefined

      Heater Fault

      Tuning and tweaking
      • • • mickey30m
      3
      0
      Votes
      3
      Posts
      511
      Views

      mickey30mundefined

      Thanks, i must over read there..

      but now it works

    • mickey30mundefined

      Problem with uploaded stl file

      Firmware developers
      • • • mickey30m
      6
      0
      Votes
      6
      Posts
      964
      Views

      Phaedruxundefined

      Probably would be a good idea to have some error rejection built in to the upload function. Maybe this can get moved to the DWC/firmware wishlist section?

    • mickey30mundefined

      My prints are in mirror, but the axis are good.

      Duet Hardware and wiring
      • • • mickey30m
      36
      0
      Votes
      36
      Posts
      3.8k
      Views

      dc42undefined

      Glad to help!