Posts made by MdMx220

M98 Pconfig.g.txt M122.txt
Not sure why it says over powered... everything is setup correctly there also. the cartridge is brand new.

@Phaedrux @mendenmh
100% sure it's a pt1000.
I checked the wiring, it's 1113Ohms @ 28C.
But, the wiring for the temp sensors were backwards, it's my bed with that fault not the hotend

It's been a while since I messed with my printer. The last thing I tried to do was getting my pt1000 sensor to work, which it doesn't.. still cannot figure out what is wrong.

It is wired into e0 temp.

Any help would be much appreciated!! config.g

@Veti I got no resistance. Thanks for reminding me that I should troubleshoot hardware also.

Even with the 'T' parameter removed, the fault stays the same.

M308 S1 P"e0temp" Y"pt1000"             	; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                                        ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                            ; disable bang-bang mode for heater  and set PWM limit
M143 H1 A157.3 C237.7 D4.4 S285                             ; set temperature limit for heater 1 to 275C

Just recently purchased and tried to install the E3D PT1000 Sensor for my hotend.

I am getting a fault with the Current reading 2000.0 C

I have the sensor wired in to E0_TEMP.

M308 S1 P"e0temp" Y"pt1000" T110000       		    ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                                        ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                            ; disable bang-bang mode for heater  and set PWM limit
M143 H1 A157.3 C237.7 D4.4 S285                             ; set temperature limit for heater 1 to 275C

The fuse was checked with multimeter, It's not blown.

I am reading 7.6V across the fan pins. With an external 5V from a buck.

I probed my V_FAN pin, verified 12V from PS.

@Phaedrux

Do I need to create the pin numbers using M574? I'm doubting this question, but it's a long shot for me right now.

@Phaedrux
Wouldn't one fan or the other turn on, with the way the config is setup now?

@Phaedrux
Extruder fan is always on

Parts cooling fan is F1

@Phaedrux
Apologies, trying to get moved into a new place.

	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MS8-6JKDA-3SS6K-K8D2Q
Used output buffers: 12 of 24 (12 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93888 of which 44 recycled
Exception stack ram used: 264
Never used ram: 8896
Tasks: NETWORK(ready,384) HEAT(blocked,1224) MAIN(running,1848) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:18 ago, cause: power up
Last software reset at 2021-01-04 17:24, reason: User, spinning module GCodes, available RAM 8688 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 17.1, current 20.7, max 20.8
Supply voltage: min 23.9, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-01-04 17:49:09
Cache data hit count 29805571
Slowest loop: 4.73ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.2ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.70ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address ec:fa:bc:5b:42:63
WiFi Vcc 3.39, reset reason Unknown
WiFi flash size 4194304, free heap 21272
WiFi IP address 192.168.1.64
WiFi signal strength -62dBm, reconnections 0, sleep mode modem
Socket states: 2 2 0 0 0 0 0 0

@Phaedrux

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.8 on Wed Nov 25 2020 13:01:16 GMT-0500 (Eastern Standard Time)

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;; GENERAL PREFERENCES ;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
G90                                              	        ; send absolute coordinates...
M83                                            	            ; ...but relative extruder moves
M550 P"NooB"                                     	        ; set printer name

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; NETWORK ;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M551 P"AAA"                                    	            ; set password
M552 S1                                           	        ; enable network
M586 P0 S1                                        	        ; enable HTTP
M586 P1 S0                                       	        ; disable FTP
M586 P2 S0                                       	        ; disable Telnet

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; DRIVES ;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M569 P0 S0                                                  ; physical drive X goes backwards
M569 P1 S0                                                  ; physical drive Y goes backwards
M569 P2 S1                                                  ; physical drive 2 goes backwards
M569 P3 S1                                                  ; physical drive 3 goes backwards
M569 P4 S1 			                    			        ; physical drive 4 goes forwards
M584 X0 Y1 Z2 E3                                           ; set drive mapping                        
;M584 X0 Y1 Z2:3 E4 P3								        ; two Z motors connected to driver outputs Z and E1
;M671 X-20:220 Y0:0 S0     							        ; leadscrews at left (connected to Z) and right (connected to E1) of X axis
M350 X16 Y16 Z16 E16 I1                				        ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E100.00     	  		        ; set steps per mm
M566 X600.00 Y600.00 Z18.00 E300.00     	 		        ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E6000.00 	  		        ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z180.00 E10000.00	 	            ; set accelerations (mm/s^2)
M906 X500 Y500 Z500 E800 I30            	  	            ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                		 		        ; Set idle timeout

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; AXIS LIMITS ;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M208 X0 Y0 Z-0.3 S1                                     ; set axis minima
M208 X220 Y220 Z400 S0                                      ; set axis maxima
M208 X-33:220 Y-7:220 								        ; X carriage moves from -5 to 205, Y bed goes from 0 to 200

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; ENDSTOPS ;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M574 X1 S1 P"!xstop"   								   	    ; X min active high endstop switch
M574 Y1 S1 P"!ystop"   									    ; Y min active high endstop switch
;M574 Z1 S1 P"zstop+e1stop" 							    	    ; configure active-high endstops for low end on Z via pins zstop and e1stop
M574 Z1 S1 P"zstop"

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;; BLTouch Bed Probe ;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M950 S0 C"exp.heater3"                                      ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000                         ; set Z probe type to bltouch and the dive height + speeds
;M307 H3 A-1 C-1 D-1                     	                ; disable heater on PWM channel for BLTouch
;M558 P9 H5 F120 T6000                   	 	 		    ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X30 Y10 Z3.6                                       ; set Z probe trigger value, offset and trigger height
M557 X20:200 Y20:200 S40                                    ; define mesh grid

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; HEATERS ;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                                       ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                                            ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                     ; map heated bed to heater 0
M143 H0 S130                                                ; set temperature limit for heater 0 to 130C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                                        ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                            ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S275                                                ; set temperature limit for heater 1 to 275C

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; FANS ;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M950 F0 C"fan0" Q500                                        ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                              ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                                        ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                                           ; set fan 1 value. Thermostatic control is turned on

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; TOOLS ;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M563 P0 D0 H1                                             ; define tool 0
G10 P0 X0 Y0 Z0                                             ; set tool 0 axis offsets
G10 P0 R0 S0                                                ; set initial tool 0 active and standby temperatures to 0C

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;; CUSTOM ;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
M302 P1                                                     ; Allow cold extrusion

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;; MISCELLANEOUS ;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

T0                                                          ; select first tool
M575 P1 S1 B57600                                           ; enable support for PanelDue
M501                                                        ; load saved parameters from non-volatile memory

M112

1/4/2021, 5:24:31 PM	Connection established
1/4/2021, 5:24:29 PM	Connection interrupted, attempting to reconnect...
1/4/2021, 5:23:48 PM	Emergency stop, attemping to reconnect...

M98 P"config.g"

1/4/2021, 5:25:23 PM	M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C

@Phaedrux

Duet.pdf

The blue and white wire is going to V_FAN pin. I confirmed 12V on that wire.

I'm guessing it has nothing to do with the GCODE?

I have also hooked both fans to 12V PS and confirmed they both work.

@Phaedrux
The photo will not so much but here it is.

I am using an open spot from the 12V PS, which is also used for the other fans to have airflow in my electrical box.

The fans do work when they have power directly from the PS.

@Veti the fan does not work always on and the fuse is good

Hello,

I can not seem to get my fans to work after upgrading to RRF 3.1.1.

I also upgraded my PS to 24V, for the VIN.

Fans are 12V, so I did wire in the 12V to the V_FAN.

I have a setup similar to the ANET A8.

M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T100 ; set fan 1 value. Thermostatic control is turned on

Any help would be much appreciated!