Ok, guys think I found the source of the problem. The connector that I made for the T0 was not tight so it was shaking when printing which creates a short inside the connector. So after about 6 hours of printing everything looks good.

Finish Print

I need to calibrate my extruders and Tune cura.
Cura
Polymaker 2.85mm PolyLite PLA Filament Translucent
.6 Nozzle
.3 Layer Height
10% Infill.
This was print at 150% scale.
https://www.thingiverse.com/thing:2849214

The Hotend (T0) Connections. This shows the new connector.

@cosmowave Got it working on E2.

Thank you

; LEDs
M950 H2 C"nil" ; free up e2_heat pin
M950 F3 C"duex.e2_heat"
M106 P3 S255 B0 H-1 C"Top Lights"
```.

Thank you, Everything seem ok.

I got it to update, I had to update to 3 then 3.2.

@jay_s_uk I got the 24v on order too, but it will ship mid December, when I get home I will work on it.

@Phaedrux

;E3d Revo Voron)
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

@jay_s_uk Hey I got it working, But the Z offset is a little different.

Got it working, you don't need a level shifter, 3.3v works for the signal, it's only 3 neopixel

M150 X4
M150 W255 P255

@Phaedrux lowered Z speed. Sounds better now.
Thanks.

@Phaedrux thank you, I got it working I replace the SD card.

@moth4017 I don’t know what’s going on with my setup because mine works for a few days and the have homing problems and then works again, I guess it’s have to deal with it the way it’s working.

@Karim This is my X Axis homing, it's not stalling now .I will let you know if this is working.

====================
; homeX.g
;====================
; called to home the X axis

M84 X
M400						    ; Wait for current moves to finish
M569 P0.1 D3 V10				; X -> B axis reduce V parameter so driver operates in stealthChop
M569 P0.2 D3 V10				; Y -> A axis reduce V parameter so driver operates in stealthChop
G4 P200						    ; Pause for 200ms to let StealthChop do some sh!t
M17 X						    ; Energize Motors X Y
M913 X20 Y20				    ; drop motor current to 20%
G4 P200						    ; Pause for 200ms to let StealthChop do some sh!t
M915 X S20 R0 F0 H200	        ; Sensitivity 9 [-64 --> 64], R - take no action, F - No filter, 200steps/sec
M201.1 X250 Y250 
G4 P200						    ; wait 200ms
G91					            ; set relative

M400                            ; Wait for moves to finish
G1 H2 X-1 F3000                 ; Move X axis back a little bit to clear stall flag if it's triggered

M400                            ; Wait for moves to finish
G4 P200						    ; wait 200ms
G1 H1 X350 F3500			    ; [ First Pass ] move quickly to X axis endstop and stop there
M400

G90						        ; absolute positioning
M400						    ; Wait for current moves to finish
M913 X100 Y100				    ; return current to 100%
M569 P0.1 D2					; Take driver out of StealthChop Mode
M569 P0.2 D2					; Take driver out of StealthChop Mode

M201.1 X650 Y650

@moth4017 Very nice Printer, I never heard of it.

@moth4017 Which printer do you have , This is a Voron 0.2 Corexy.

@moth4017 Mine stall at first homing, X would stall, but if you get X to home successfully. Home all work every time, but if printer is power off overnight in the morning you have to go through that procedure again.

@Phaedrux ok I change the Z value in M208 S0 Z118.17 in config-override.g and then restart to get the nozzle closer to the bed. I will test and report back the evening.

@moth4017 Hey no I did try M201.1, I been working on this printer for two weeks now trying to get sensor-less homing to work properly . I have two duet 2 wifi with duex5 and they working flawlessly. I know what you are saying about homing, I have to home x and y separately then home all works it’s a hit or miss.

@Phaedrux yes bed is at print temperature always.

; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Feb 04 2023 22:42:11 GMT-0500 (Eastern Standard Time)

; General preferences
M575 P1 S1 B57600                                    ; enable support for PanelDue
G90                                                  ; send absolute coordinates...
M83                                                  ; ...but relative extruder moves
M550 P"Zero"                                         ; set printer name
M669 K1                                              ; select CoreXY mode

; Network
M551 P"Zero"                                         ; set password
M552 S1                                              ; enable network
M586 P0 S1                                           ; enable HTTP
M586 P1 S0                                           ; disable FTP
M586 P2 S0                                           ; disable Telnet

; Drives
M569 P0.1 S1 D2 ;F3 B2 Y5:3                           ; physical drive 0.1 goes forwards
M569 P0.2 S1 D2 ;F3 B2 Y5:3                           ; physical drive 0.2 goes forwards
M569 P0.0 S1 D3 V50                                  ; physical drive 0.0 goes forwards
M569 P0.3 S0 ;D2                                      ; physical drive 0.3 goes forwards
;M915 X Y R0 F0

M584 X0.1 Y0.2 Z0.0 E0.3                             ; set drive mapping
;M592 D0.3 A0.01139 B0.00088                         ;Set Non-Linear Extrusion

M350 X16 Y16 Z16 E16 I1                              ; configure microstepping with interpolation
M92 X80 Y80 Z400.00 E413.52 		                     ; set steps per mm
M566 X480 Y480 Z100 E1200 		                 ; set maximum instantaneous speed changes (mm/min)

M203 X18000.00 Y18000.00 Z1800.00 E12000              ; set maximum speeds (mm/min)
M201 X10000 Y10000 Z200.00 E2500                      ; set accelerations (mm/s^2)
M906 X650 Y650 Z300 E550 I40                          ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                               ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                      ; set axis minima
M208 X120 Y120 Z120 S0                                ; set axis maxima

; Endstops
M574 X2 S3 ;P"^io3.in"                                ; configure switch-type (e.g. microswitch) endstop for high end on X via pin !^io3.in
M574 Y2 S3 ;P"^io5.in"                                ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin !^io5.in
M574 Z2 S1 P"^io6.in"                                 ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin !^io6.in

; Z-Probe
;M950 S1 C"out6"                                      ; assign GPIO port 1 to out6 (Servo header), servo mode
M558 P0 ;P5 K0 C"^io1.in" R0.1 A5 H1 F600:400 T6000
;G31 X60 Y60 Z0
M557 X0:120 Y0:120 P3
M671 X60:5:115 Y5:-10:115 P0.5                        ; adjusting screws

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                    ; create bed heater output on out0 and map it to sensor 0
;M307 H0 R0.616 K0.698:0.000 D3.15 E1.35 S1.00 B0 V24
M307 H0 R0.240 K0.131:0.000 D5.22 E1.35 S1.00 B0 V24
M140 H0                                               ; map heated bed to heater 0
M143 H0 S120                                          ; set temperature limit for heater 0 to 120C

;E3d Revo Voron)
M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.06e-8       ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"out1" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 R4.091 K0.614:0.000 D1.92 E1.35 S1.00 B0   ; disable bang-bang mode for heater  and set PWM limit
M307 H1 R4.167 K0.511:0.000 D2.11 E1.35 S1.00 B0 V23.7
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

M308 S2 P"temp2" Y"thermistor" A"Chamber" T100000
M308 S11 Y"drivers" A"Duet stepper drivers"

; Fans
M950 F0 C"out3" ;Q250				                  ; create fan 0 on pin out3 and set its frequency
M106 P0 S0 H-1 C"Part"                                ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out5" ;Q500                                 ; create fan 1 on pin out5 and set its frequency
M106 P1 S1 H1 T45 C"Hotend"                           ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"out4"
M106 P2 C"Filter" S0 H-1
;M106 P2 C"Filter" S1 H0 T45

; Tools
M563 P0 S"Main" D0 H1 F0                              ; define tool 0
G10 P0 X0 Y0 Z0                                       ; set tool 0 axis offsets
G10 P0 R0 S0                                          ; set initial tool 0 active and standby temperatures to 0C

;Neopixel
M150 X1 Q3000000                                       ; set LED type to NeoPixel and set SPI frequency to 3MHz
M150 U150 P100                                        ; set to red, half brightness,

; Custom settings are not defined
; Misc
;M912 P0 S-4                         ; MCU temperature calibration (yours will be different)
;M572 D0 S0.075                      ; Pressure Advance
M572 D0 S0.01                       ; Pressure Advance
M592 D0 A0.015 B0.0012 L0.2         ; Non-linear extrusion
M376 H10                            ; Fade mesh out compensation over 10mm Z


; DAA tuning (you will need to change this for your slicer)
;M593 F26.6                          ; Cura 4.5 stock profile @ 40mm/s outer printing speed
;M593 F42.5                          ; PrusaSlicer @ 40mm/s outer perimeter

M671 X60:5:115 Y5:-10:115 P0.5 ; adjusting screws

; Miscellaneous
T0                                                    ; select first tool
M280 P1 S1
M400
M280 P1 S-1

M98 P"/sys/lib/init.g"
M501

; config-override.g file generated in response to M500 at 2023-02-26 17:50
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 R0.240 K0.131:0.000 D5.22 E1.35 S1.00 B0
M307 H1 R4.167 K0.511:0.000 D2.11 E1.35 S1.00 B0 V23.7
; Probed axis limits
M208 S0 Z118.17
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

; homez.g
; called to home the Z axis
;
G91
G1 H1 Z300 F800                  ; move Z down until the endstop is triggered
M400
G1 H2 Z-5 F300                    ;back away
G1 H1 Z300 F60                    ;second pass
G4 S1			                  ; wait 1s
G90
;G92 Z119                        ; set Z position to axis minimum
M400

;Start G-code
M83               ; set extruder to relative mode

G21               ; set units to mm

T0                ; select tool 0

G92 E0.0          ; reset extruder position

M220 S100         ; reset speed multiplier

G28               ; Home All Axes

;End G-code
G91				; relative positioning

M83                             ; extruder relative positioning

G1 E-5.00 F1000                 ; retract 5mm of filament

G1 Z1.00 X20.0 Y20.0 F20000     ; short quick move to disengage from print

;G1 Z10.00 F20000                ; move Z-Axis 10mm away from part

G28 Z

G90                             ; absolute positioning

G1 X120 Y3120 F9000              ; move gantry close to home

M104 S0                         ; turn off hotend

M140 S0                         ; turn off heatbed

M106 S0                         ; shut off blower

M84                             ; turn off motors

@Phaedrux ok I let the nozzle top a piece of paper and then zero. But when I go to print the nozzle it a little too high. Do I change the Z0 to Z18.35

; Axis Limits
40 M208 X0 YO Z0 S1
41 M208 X120 Y120 Z120 SO

@Phaedrux ok, I got 118.85 from nozzle to bed switch. Look like it’s working, so I noticed z babystepping not working. I have to disable axis limit (M564 S0) to go closer to nozzle.