Topics created by jerolee

@jerolee said in Bed probing:

@fcwilt
Im running my very first testprint on this homemade printer now, is awesome feeling 🙂
thanks for the fast reply!

Glad I was able to help.

Frederick

@droftarts
RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.3 ELECTRONICS: Duet WiFi 1.02 or later + DueX5 FIRMWARE_DATE: 2021-06-15 21:45:03

I did the changes PCR suggested otherwise i would never have found the solution 🙂
@PCR
Thanks mate, by removing values from the config as you suggested, the odd behaviour of the software was gone and round pancake worked.

@dc42
When i use the SD card without any structure, so just put a gcode file on the blank card it doesnt get recognized.
Only when i create a folder on the card, it gets read.
Even i can name it "new folder" and leave it empty the SD card is recognized as such.
So the card appears to need some structure on it to able to be recognized.

Its not that biggie but Marlin does read the Gcodes directly, i dunno if you could change the connect commands in such a way that it detects the card wether or not it has something on it?
detect media or something?

@dc42
Boards Duet2 wifi with Duex5.
Firmware 3.3 but also same problem with 3.2.2. i updated to see if the bug was solved in 3.3.
This configuration works fine. When u change the second Y-motor to a driver and endstop on the duex5 it doesnt work.

M575 P1 S1 B115200 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Contronix3D" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 4 goes backwards
M569 P4 S0 ; physical drive 4 goes backwards
M569 P5 S0 ; physical drive 5 goes backwards
M569 P6 S0 ; physical drive 6 goes backwards
M569 P7 S0 ; physical drive 7 goes backwards

M584 X0 Y1:3 Z2:4:5:6 E7 ; set drive mapping
M350 X16 Y16 Z16 E16:16:16:16:16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z1600.00 E932.00:80.00:1600.00:1600.00:1600.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E50.00:900.00:60.00:60.00:60.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z360.00 E500.00:6000.00:360.00:360.00:360.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00:500.00:20.00:20.00:20.00 ; set accelerations (mm/s^2)
M906 X650 Y650 Z700 E800:650:700:700:700 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X600 Y299 Z500 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"!xstop" ; configure active-low endstop for low end on X via pin !xstop
M574 Y1 S1 P"!ystop+!e0stop" ; configure active-low endstop for low end on Y via pin !ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"duex.pwm1" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X53 Y-2 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X25:565 Y15:285 S90 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 R4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4000 R4700 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 R2.926 C244.4 D10.45 S1.00 V25.0 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S260 ; set temperature limit for heater 1 to 260C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 "part fan" on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 "hotend fan"on pin fan1 and set its frequency
M106 P1 S1 H1 T70 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

@jerolee NOW my interest is even bigger!
I'm trying to figure out a way to run 11-12 steppers on my hashPrinter without braking the bank. I'm in the process of upcycling an old RADDS shield as a Duet2 expansion.