Firstly sorry for the post count.
I am trying to get the filament to extrude and fromt octoprint, webduet or the touch screen on the printer i get this
Recv: Warning: Macro file /macros/filament/do_moves_for_load.g not found
I have loaded all the macros included in the firmware installation but there's nothing called do_moves.
What have i fkd up?
So i am trying to level the bed on the old Troodon now that the guys here have helped me sort the issues Vivendon put in their cura profile
anyway i get this from a G29
Send: G29 X400 Y400
Recv: Warning: Skipping grid point (15.0, 15.0) because Z probe cannot reach it
I have edited my config to define the bed mesh as 400, 400, 500 and the BLtouch mesh to 385 ,385.
Tell ya what, this reprap is a lot better but a big learning curve from marlin.
@oliof
well would you look at that.....just got the cura going and found not only was it set to marlin but the start code was
M42 P25 S0
M42 P26 S0
M42 P24 S255
M280 P7 S160
T0
G92 E0
G1 E-10 F1800
G32
G29
G1 X0 Y0 F4800
G92 E0
G1 E10 F540
G92 E0
G1 E-3.0000 F1800
G1 Z0.200 F1000
G1 X400 Y0 E43.5631 F1000
G92 E0
G1 E-8.0000 F5400
G1 X205 Y200 F18000
G1 E0 F5400
I just entered M42 P25
Send: M42 P25
Recv: Error: Invalid gpio port 25
Recv: ok
and it throws the error outside of starting a print.
Thanks guys,
i'll test out M42 P25 in a short while, i think i might try and find the RRF2.X firmware and go back to that.
@phaedrux
don't have a link to the files do you?
also as i have a rare not well known printer i am a little hesitant to update further without some files to make sure it runs on this big girl, it's a work printer not mine personally.
i tried to post those in the </> and it was flagged as spam
Send: M98 P"CONFIG.G"
Recv: Error: M574: endstop type 0 is no longer supported. Use type 1 and invert the input pin instead.
Recv: Error: M574: endstop type 0 is no longer supported. Use type 1 and invert the input pin instead.
Recv: Turn off the current WiFi mode before selecting a new one
Recv: HTTP is enabled on port 80
Recv: FTP is disabled
Recv: TELNET is disabled
Recv: Error: M307: Heater 3 not found
Recv: Warning: M307: heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 542C.
Recv:
Recv: Error: M106: Fan number 3 not found
Recv: Error: M106: Fan number 4 not found
Recv: Error: M106: Fan number 5 not found
Recv: Error: M106: Fan number 6 not found
Recv: Error: M106: Fan number 7 not found
Recv: Error: M106: Fan number 8 not found
Recv: Warning: M307: heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 763C.
Recv:
Recv: ok
Send: M122
Recv: === Diagnostics ===
Recv: RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later + DueX5
Recv: Board ID: 0JD0M-9P61A-J8PSJ-6JTD8-3S46M-9BQUS
Recv: Used output buffers: 1 of 24 (10 max)
Recv: === RTOS ===
Recv: Static ram: 30516
Recv: Dynamic ram: 92516 of which 16 recycled
Recv: Exception stack ram used: 592
Recv: Never used ram: 7432
Recv: Tasks: NETWORK(ready,640) HEAT(blocked,1240) DUEX(suspended,160) MAIN(running,1320) IDLE(ready,156)
Recv: Owned mutexes:
Recv: === Platform ===
Recv: Last reset 03:23:57 ago, cause: software
Recv: Last software reset at 2021-09-10 10:30, reason: User, spinning module GCodes, available RAM 7836 bytes (slot 3)
Recv: Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Recv: Error status: 8
Recv: Free file entries: 10
Recv: SD card 0 detected, interface speed: 20.0MBytes/sec
Recv: SD card longest block write time: 6.0ms, max retries 0
Recv: MCU temperature: min 31.4, current 32.2, max 33.2
Recv: Supply voltage: min 23.9, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Recv: Driver 0: standstill, SG min/max 0/324
Recv: Driver 1: standstill, SG min/max 47/307
Recv: Driver 2: temperature-shutdown! short-to-ground standstill, SG min/max not available
Recv: Driver 3: standstill, SG min/max not available
Recv: Driver 4: temperature-shutdown! short-to-ground standstill, SG min/max not available
Recv: Driver 5: standstill, SG min/max 0/326
Recv: Driver 6: standstill, SG min/max 0/1023
Recv: Driver 7: standstill, SG min/max 0/322
Recv: Driver 8: standstill, SG min/max 0/1023
Recv: Driver 9: temperature-shutdown! short-to-ground standstill, SG min/max not available
Recv: Date/time: 2021-09-10 13:54:07
Recv: Cache data hit count 4294967295
Recv: Slowest loop: 25.74ms; fastest: 0.09ms
Recv: I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
Recv: === Move ===
Recv: Hiccups: 0(0), FreeDm: 169, MinFreeDm: 163, MaxWait: 7856434ms
Recv: Bed compensation in use: none, comp offset 0.000
Recv: === MainDDARing ===
Recv: Scheduled moves: 379, completed moves: 379, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
Recv: === AuxDDARing ===
Recv: Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
Recv: === Heat ===
Recv: Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Recv: === GCodes ===
Recv: Segments left: 0
Recv: Stack records: 3 allocated, 0 in use
Recv: Movement lock held by null
Recv: http is idle in state(s) 0
Recv: telnet is idle in state(s) 0
Recv: file is idle in state(s) 0
Recv: serial is ready with "M122" in state(s) 0
Recv: aux is idle in state(s) 0
Recv: daemon is idle in state(s) 0
Recv: queue is idle in state(s) 0
Recv: autopause is idle in state(s) 0
Recv: Code queue is empty.
Recv: === Network ===
Recv: Slowest loop: 8446.66ms; fastest: 0.00ms
Recv: Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
Recv: HTTP sessions: 0 of 8
Recv: - WiFi -
Recv: Network state is running
Recv: WiFi module is providing access point
Recv: Failed messages: pending 0, notready 0, noresp 1
Recv: WiFi firmware version 1.23
Recv: WiFi MAC address 4a:3f:da:51:11:37
Recv: WiFi Vcc 3.41, reset reason Hardware watchdog
Recv: WiFi flash size 4194304, free heap 24608
Recv: WiFi IP address 192.168.1.1
Recv: Connected clients 1
Recv: Socket states: 0 0 0 0 0 0 0 0
Recv: === Filament sensors ===
Recv: Extruder 0 sensor: ok
Recv: ok
I have a Vivendo Troodon 400,
Updated the firmware following the instructions the the best i understood and i am not that up to scratch with reprap but everytime i go to start a print it reports this; Error: Invalid gpio port 25
this is the report i get.
Changing monitoring state from "Starting" to "Printing"
[...]
Send: N3 M8226
Recv: ok
Send: N4 M42 P25 S037
Recv: Error: Invalid gpio port 25
Changing monitoring state from "Printing" to "Cancelling"
i have tried deleting the RGB code but it still throws the same error.
I am using the duet page to do everything but ultimately i'll be using Octoprint.
Any help would be greatly appreciated.