Posts made by Egon.Net

@droftarts Thanks, I'll wait then.

@droftarts My bad, It was beta2+4... I remember reading a post that suggests using version 3.5.1 with the 3.6 betas... I'm right now in 3.5.0, and I'm experiencing issues (all temperatures are .0 and refreshes work only every other time)

I have just updated RRF to 3.6.0 beta4, which is supposed to go with PanelDue FW 3.5.1, but I can only find 3.5.0 version, is it a beta version hosted anywhere?

Thanks!

https://www.reddit.com/r/prusa3d/comments/1b2577t/comment/ksj8ff7/?share_id=CR6_0Y-1uBdp7iVZoW9DP

It would do a enormous difference for my setup...

I don't have any more boards, but you can go with S1lencer ones

I used mouser, and I have just checked and they have them in stock...

Here it is:

https://github.com/EgonVLC/PWM2Analog

Multisim/Ultiboard files, GERBERS, schematic and build instructions.

I will add further info when possible.

Hi all, I'm sorry I have been quite busy for personal reasons. I will try to post all the resources in github and share the link today.

Best regards.

@danielkrah I already use a PEI sheet, but there's no adherence at all. I end up with the adhesive tape, and it kinda works.

Any news about this issue?

@evan38109 I'm having the very same problem, you are not alone.

@mfs12 said in Macros not showing on control page after updating from 1.24:

Hey @Egon-Net,

here we are one step further. I hope now it's fixed. Found another "off-by-one" error.

The macro button short list is displayed when there are at least 2 tool slots free.

Please test the attached image and provide a short feedback.

paneldue-3.4.0-dev-egon.net-v3-7.0.bin

Tested, and it's working on the "control" page, the macros buttons are shown. But in "status" page are not shown, is that intended?

Thank you very much!

@dc42 said in RRF 3.4 input shaping preview available:

@jenpet said in RRF 3.4 input shaping preview available:

@dc42 the two contour lines get thinner and thinner at the end so that there is a gap between them.
Now I try to lower PA value again.

If you mean the two perimeter lines, they are joined in the perimeter at the top, joined for part of the length of the perimeter on the right, and not joined at all in the perimeter at the bottom. The difference between top and bottom suggests to me that you have chosen an unfortunate wall thickness and the slicer has failed to ensure consistent infill by altering the extrusion widths - so that whether the perimeters are joined or not is very sensitive to small changes. I am assuming that the thickness of all three walls is supposed to be the same.

I also have problems with pressure advance and input shaping with de PA values I already got finetuned without input shaping.

Top one: input shapping ei3 @48Hz + PA 0.1 (orbiter extruder direct)

Bottom one: just input shapping and no PA

Both 100mm/sec, 6000mm/s2 acceleration

You can see corners are ok with the PA, and bulges with no PA...

@mfs12 said in Macros not showing on control page after updating from 1.24:

Hey @Egon-Net,

i was using this configuration and It displayed me macro buttons (it hast only 5 bed and tools configured):

https://forum.duet3d.com/post/236725

In case of more than 5 tools and beds no maco buttons are displayed.

Please use the version is sent: paneldue-3.3.0-rc4-egon.net-v3-7.0.bin

Because PanelDue-3.3.0 does NOT contain this fix yet!!! It will be released with the next release cycle.

I returned to paneldue-3.3.0-rc4-egon.net-v3-7.0.bin again, and launched a test print, just in case. No macro buttons. Anything else I could test?

@mfs12 said in Macros not showing on control page after updating from 1.24:

Hey @Egon-Net,

i was using this configuration and It displayed me macro buttons (it hast only 5 bed and tools configured):

https://forum.duet3d.com/post/236725

In case of more than 5 tools and beds no maco buttons are displayed.

Please use the version is sent: paneldue-3.3.0-rc4-egon.net-v3-7.0.bin

Because PanelDue-3.3.0 does NOT contain this fix yet!!! It will be released with the next release cycle.

I used the version you sent me (the egon.net one) and got no luck with the macro buttons. I have exactly one bed and 4 tools (1 heater each). I just tried the 3.3.0 final just to check if the baudrate was related to the custom version.

@egon-net
Lowering to 57600 bauds connects, but still no macros buttons are shown. Updated also to 3.3.0 final, and got 115200 bauds working again, but also no macro buttons.

@mfs12
Just updated, but PanelDue now does not connect... Do I have to do something else?

@mfs12 said in Macros not showing on control page after updating from 1.24:

Hey @egon-net, i think i could fix the problem you reported.

it would be really helpful if you could test it with your setup. I assume from your report you are using a PanelDue v3-7.0. So the image is exactly for that hardware. Looking forward to hear from you.

paneldue-3.3.0-rc4-egon.net-v3-7.0.bin

Thanks! I'll test it tomorrow morning and report!

@phaedrux said in Bed mesh correction and tool offsets...:

Can you try doing a higher density mesh of only the small area in the center of the bed where you will be printing and see if that helps. Or if you have the time, probe the entire bed with a higher density. You're using 100 points of a possible 441.

I aleady do, and I have the very same problem