Posts made by Deluxe 600

@dc42 After a bit of trial and error i figured it out .
For some reason adding just M98 P"pause.g" in the filament-error does nothing.
So i just copied everything from pause.g to filament-error.g but then i wanted the tool to be put in stand by. After a few tries i figured out it needs to be writen is specific order to work.
So here is my final version of filament-error.g that actualy does what its suposed to.

G10 P0 R20 ; Set standby temp of tool 0 to 20*
M83 ; relative extruder moves
G1 E-50 F2000 ; retract 10mm of filament
G91 ; relative moves
G1 Z5 F500 ; raise nozzle 5mm
G90 ; absolute moves
G1 X20 Y525 F6000 ; go to X=20 Y=525
T-1 ; Deselect tool

Thank you for the help guys, have a great day.

@dc42 Thanks, i will try that and let you know.

@dc42
So if i understand it correctly. I need to find or make filament-error#.g and put the contents of
filament-change.g in it? Or how should i do it correctly?

Or maybe delete the filament-error#.g or filament-error.g for it to run pause.g?

Best would be if i could somehow run filament-change.g as a result of no fillament trigger.

@phaedrux Thank you for the reply.
I am using filament sensor from Prusa MINI because i had it laying around.
Its a optical gate acting like a normal switch.

The sensor works as the print stops and the light on the board turns on.

I understand i need the filament runout to send M600 command but i dont know how to do it.

@phaedrux
Hi, thank you for the fast responce .
Here is my config.g

; General preferences
G90                              ; Send absolute coordinates...
M83                              ; ...but relative extruder moves

; Network
M111 S0 ; Debug off
M550 Deluxe600 ; Machine name (can be anything you like)
M551 inman. ; Machine password (used when you connect Duet Web Control or via FTP)
M540 PBE:EF:DE:AD:FE:ED ; MAC Address (only needed if you have more than one Duet 0.6 or 0.8.5 on the same network)
M552 S1 P192.168.210.202 ; IP address (0 = use DHCP)
M554 P192.168.104.217     ; Gateway (not used yet)
M553 P255.255.255.0 ; Netmask
M555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; Set auxiliary serial port baud rate and require checksum (for PanelDue)


; Drives
M569 P0 S1                       ; Drive 0 goes forwards
M569 P1 S1                       ; Drive 1 goes forwards
M569 P2 S1                       ; Drive 2 goes forwards
M569 P3 S1                       ; Drive 3 goes forwards
M584 X0 Y1 Z2 E3                 ; set drive mapping
M350 Z8 X16 Y16 I1               ; Configure microstepping with interpolation
M350 E32 I0                      ; Configure microstepping without interpolation
M92 X50 Y50 Z400 E280            ; Set steps per mm 
M566 X480 Y480 Z5 E270         ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z720 E7200    ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z125 E5000      ; Set accelerations (mm/s^2)
M906 X1400 Y1400 Z2200 E700 I1   ; Set motor currents (mA) and motor idle factor in per cent
M84 S5                           ; Set idle timeout


; Axis Limits
M208 X0 Y0 Z0 S0                 ; Set axis minima
M208 X545 Y545 Z675 S0           ; Set axis maxima

; Endstops
M574 X1 S1 P"!xstop"                           ; configure active-high endstop for low end on X via pin xstop
M574 Y2 S1 P"!ystop"                           ; configure active-high endstop for low end on Y via pin ystop
;M574 Z1 S2                                    ; configure Z-probe endstop for low end on Z                   

; Z-Probe
M950 S0 C"exp.heater3"                         ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" A5 H4 F100 T6000         ; set Z probe type to bltouch and the dive height + speeds
G31  X0 Y0 Z0.9                                ; set Z probe trigger value, offset and trigger height
M557 X0:500 Y40:500 S100:100                   ; define mesh grid

;Filament Runout Sensor
M591 P1 C"e0stop" S1 D0 ; filament monitor connected to E0 endstop

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S100                                   ; set temperature limit for heater 0 to 100C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S0.5 H1 T60                            ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                           ; create fan 2 (bed) on pin fan2 and set its frequency
M106 P2 S1 H0 T50   

; Tools
M563 P0 D0 H1                  ; Define tool 0
G10 P0 X0 Y0 Z0                  ; Set tool 0 axis offsets
G10 P0 R20 S0                     ; Set initial tool 0 active and standby temperatures to 0C
 
;LED control
M950 P5 C"e1heat" ;set e1heat as a GPIO output pin
M501
M107

M122

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet Ethernet 1.02 or later
Board ID: 08DDM-9FAMU-JW4S4-6JKD8-3SJ6M-T3Y7V
Used output buffers: 3 of 24 (15 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 70804 of which 0 recycled
Never used RAM 19736, free system stack 126 words
Tasks: NETWORK(ready,24.5%,244) HEAT(delaying,0.0%,330) Move(notifyWait,0.1%,313) MAIN(running,75.2%,445) IDLE(ready,0.3%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:05:30 ago, cause: power up
Last software reset at 2021-07-28 10:51, reason: User, GCodes spinning, available RAM 16640, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 29.0, current 39.8, max 40.2
Supply voltage: min 24.1, current 24.3, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 750, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max 0/226
Driver 2: position 1964, standstill, SG min/max 0/376
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-07-31 20:31:26
Cache data hit count 4294967295
Slowest loop: 6.18ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.4ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 136889ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 14, completed moves 14, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 1], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 15.52ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex

M98 P"config.g"

RepRap name: My Duet
Error: Bad command: man. 
Error: Z axis maximum must be greater than minimum
7/31/2021, 8:31:27 PM	M122

filament-change.g

M83 ; relative extruder moves
G1 E-5 F2000 ; retract 5mm of filament
G91 ; relative positioning
G1 Z10 F360 ; lift Z by 10mm
G90 ; absolute positioning
G1 X5 Y272.5 F6000 ; go to X=0 Y=0
M98 P"Unload"
M25

Hello.
I have a strange problem that i cant seem to figure out.
I have a simple filament sensor that has a siwitch and is conected to the endstop.
Problem is that it does detect the filament runout but just shows "Extruder0 reported noFilament" and stops printing, i cant seem to get it running again.

In the config its setup like this:M591 P1 C"e0stop" S1 D0 ; filament monitor connected to E0 endstop

I would like the sensor when it detects no filament to run the "filament-change.g" macro i have created for it. Could you guys please help?


@phaedrux Never mind i figured it out.
For anyone wondering the gcode that worked is M591 P1 C"e0stop" S1 D0

Thank you all for the help, you are the best

@jay_s_uk It works! Thank you . But the filament sensor doesnt show up, thats strange isnt it? I just have X,Y,Z endstops in the "ENDSTOPS" page

@phaedrux And it works . Thank you guys. Now only to solve the filament sensor, working on it right now. Im trying to use the sensor from Prusa MINI but it seems to need 5V power. So i conected the power pin one the sensor to the always on FAN that has 5V.

@phaedrux Thank you for the reply.

But so far i was unsucesful.
I have tried to install the plugin but for some reason it does not want to work.
I have exported the "Monitor Plugin" to the src/plugin folder and even modified "Index.js" as instructed, but it still doesnt show up in the "plugins" folder in webcontroll.

Meanwhile i also tried to setup the fil sensor but that too didnt manage to get it working i will send the config file also if you could please take a look if i have it setup corectly.
Thank you very much.

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 Z8 X16 Y16 I1 ; Configure microstepping with interpolation
M350 E32 I0 ; Configure microstepping without interpolation
M92 X50 Y50 Z400 E280 ; Set steps per mm
M566 X480 Y480 Z2 E270 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z720 E7200 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z125 E5000 ; Set accelerations (mm/s^2)
M906 X1500 Y1500 Z2000 E700 I1 ; Set motor currents (mA) and motor idle factor in per cent
M84 S5 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S0 ; Set axis minima
M208 X545 Y545 Z700 S0 ; Set axis maxima

; Endstops
M574 X1 S1 P"!xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y2 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin ystop
;M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" A5 H4 F100 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 X0 Y0 Z0.9 ; set Z probe trigger value, offset and trigger height
M557 X0:500 Y40:500 S100:100 ; define mesh grid

;Filament Runout Sensor
M950 J0 C"!e0stop" ; create switch pin
M591 P2 C"e0stop" S1 D0 ; filament monitor connected to E0 endstop

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S100 ; set temperature limit for heater 0 to 100C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S0.5 H1 T60 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 (bed) on pin fan2 and set its frequency
M106 P2 S1 H0 T50

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R20 S0 ; Set initial tool 0 active and standby temperatures to 0C

;LED control
M950 P5 C"e1heat" ;set e1heat as a GPIO output pin
M501
M107

Hi, I wanted to set up a filament sensor using a Prusa MINi fil sensor just because i had one.
But when i tried to test it to see if the printer detects it, i noticed that the tab "machine properties" had vanished.Im using Webcontrol 3.2.0 and duet 2 ethernet FW 3.0 .

The second thing is that i dont know how to set up the fil sensor properly
Sensor is just an optical gate so i guess its like a regular switch. Its pluged into the E0 endstop and all i want is for it to pause the print when it detects a run out.

Here is the config
;Filament Runout Sensor
M950 J0 C"!^e0Stop" ; create switch pin
M581 P0:1 T2 S1 R1 ; run trigger2.g to pause if filament has run out during SD card printing

Thank you and have a great day.

Good morning.

I am trying to figure out how to do this:

Printer runs out of filament and filament sensor detects it so it unloads whats left of the old spool and loads a new one. I have direct drive extruder so that complicates the task a bit.

My idea is to buy a driver expansion board and use something like Prusa MMU2.

Did anyone try to solve this idea?

Thank you for your suggestions

@fcwilt Yes the very first line in the file.

@dc42 said in Pause.g Resume.g problems:

if state.currentTool != -1 M83 ; relative extruder moves G1 E-4 F2500 ; retract 4mm G91 ; relative moves G1 Z5 F5000 ; raise nozzle 2mm G90 ; absolute moves G1 X0 Y85 F10000 M106 S0

Ok...so i have found out what was the problem with the FAN. I cant believe it was this trivial, any way the only reason the FAN didnt start up on resume was that the M106 R1 has to always be on the first place otherwise it just doesnt work. When i found out it was this all along i was happy and mad at the same time. Thank you all for your help we finaly did manage to get it working. Have a great day

@Phaedrux Thank you. Meanwhile i will try to figure it out, if i find any way to solve this problem i will let you know.

I think its a bug in the software. There is no reason why should this not work, you guys dont use pause on your printers? I went trough every forum i could find and the M106 R1 command should turn the print fan back on...but it doesnt for unknown reason.

@Phaedrux Hi.
So i have updated to 3.2 and tried the pause.g with M107 and also with M106 S0 and the resume.g with M106 R1 and also with M106 R2 but still no luck. Seems like the M106 R1 command sets the speed always to 0rpm. Thank you guys for helping.

It is S255 for PLA but once you start printing PETG the speed changes how its needed. No i havent tried 3.2 yet. Could it solve this problem?

@Phaedrux Hi.
Im using PrusaSlicer for slicing.
Here is a gcode i tried printing.
test 1_0.3mm_PLA_MK3.gcode

Well didnt know this would be such a problem