Posts made by CrazyCreator

@chrishamm thanks for info ... i have installed and now is all fine again

@jay_s_uk
That's what i mean ... We have to wait.

ok ... Now i have installed 3.5.0-rc.4 ...

Thanks for helping

I'm currently on the unstable channel... but I can't get an update to 3.5.0 loaded.

This is probably due to the reasons you wrote in your previous post?

@jay_s_uk
Ahhhh ... ok ... I go a step back and use this file:

right?

Unfortunately, my MB6HC choked during the last firmware update.

Which file to load for MB6HC?
Unfortunately, my MB6HC choked during the last firmware update.

Now if I want to reset the board.

With this guide: https://docs.duet3d.com/en/User_manual/RepRapFirmware/Updating_firmware#all-other-duet-boards

Which file do I need to download exactly?

@jay_s_uk
But ... My Erase Button is on Position from v0.6 and on the Board itself is writing v1.01 ... it's a little bit funnny

@infiniteloop

I know... I saw that.
I just wanted to show that there are also duet boards where the jumper is in a different place. So it's quite possible that this is the case on my board too.

@jay_s_uk
What kind of rubbish is that?
Well then I'll try to bridge the two pins.
If the board wears out, then at least an original one comes in

btw
Here is a picture of a board from Filafarm (official seller in Germany), there is no erase jumper at this position. However, that is a 0.6 board in the picture.

@jay_s_uk The board came with the printer... No idea if it's a clone or not. But the clones are also made according to the specifications, aren't they?

@droftarts Mhhhh ... Thanks all for the helping, but i don't have a erase jumper

@chrishamm
Unfortunately, I can't find how to flash the firmware from the Pi onto the board. Can access the Pi via VNC...

And next strange problem. In the Docu is writing:
Erase the firmware on the Duet by either:
Pressing the Erase button (next to the reset button on older Duets); or Jumpering the erase jumper
Remove the erase jumper once the Diag LED lights up.

But i can't find this Pins for jumper it.

Maybe this is the reason for this:

But what's much stranger is that when I connect the board to the USB on the PC, nothing happens.

Neither on the Mac nor on the Windows PC... The board does not appear.
Do I have to disconnect all cables (Motor, Endstops, heater etc) beforehand and only the USB cable can be plugged in?
All other cables are of course without power, the main switch of the printer is turned off.
.

@chrishamm omg ... really? the hard way?

Today i try to Update my Board.

But:

Now i only can connect with ssh.
No connect per LAN or WLAN possible.

How can i restart the update prozess?

On DWC i see this:

I try to install this plugin, but in console i have this error:

SystemInfo:

Any hints for me?

@chrishamm
Now it works ... Thanks for the update

@jay_s_uk Yes ... Of course ... Is standard

Every time this way:

sudo apt-get update
sudo apt dist-upgrade

And a little hint:
I try to update the dwc with the dwc-zip-package per dwc-interface and the button "Upload System Files" ...
But doesn't work too.

@jay_s_uk Now is later. and the e-mail is out ... but i have the same problem.

@CCS86 good idea ...

here is the new one ...

i think 0,034 or 0,035 is the sweet spot.

I don't see any difference ... i'm a old blind man

But i think my steps to big ... now i posted the picture i see it.

@oliof stupid question ... in my config.g i have to disable the M572 or is overwritten from the g.code?