video_2021-02-11_00-13-44(1).mp4
We are doing some prototyping, with a regular orbiter, changing some aspects of the body.
It actually is a pivot extruder, so it can rotare freely within the rod arms...
It´s not my doing, just a friend´s I am helping him to achive it
@arhi I meant the the first prototype had wifi disconections due to long tracks, this one has shorter pads, and looks like it works just fine while printing. The first one just didn´t work while printing
@Fred-Y I use a ptfe foil to lubricate ball-arm joints.
Here a bunch of spanish guys are using this ptfe tape on our hayden´s arms.
some where I found this some time ago
Macro "leds on/off"
if state.gpOut[1].pwm == 1
M42 P1 S0
else
M42 P1 S1
in config files
; LEDS
M950 P1 C"e1heat" Q500 ;use heater 1 outupt for LED
M42 P1 S1 ; turn off LEDS
@Branzo said in Thermistor Semitec 104nt config problem:
M308 S0 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8
M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H0 S500 ; set temperature limit for heater 0 to 500C
if you declared S0 and H0 has the heated bed, need to declare S1 and H1 as the heater
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8 A"Nozzle E0" R4700 ; E3d configure sensor 0 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 2
M143 H1 S285 A2 ; disable temporarily H1 if temp exceeds 285C
M143 H1 S295 A0 ; heater fault H1 if temp exceeds 295C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M570 H1 P10 T30 ; heater fault for 10 seg of 30ºC excursion
just saw new source for smarteffector v4 on github, what would be new on it, is it there any specs or pictures?
@apak 
seems everything is in place, also the 74HC74
guess that the chinnese clons just install everything for the wifi version and then just plug the ethernet board
@oarjjj said in v2.0 consistently increasing probe heights:
M208 Z0 S1 ; set minimum Z
Need to go under Z=0 with contact probe like smarteffector.
@janjoh I use a simple macro to turn on and off the leds...
Definition in config.g
; LEDS
M950 P1 C"e1heat" Q500 ;use heater 1 outupt for LED
M42 P1 S1
macro LED ON/OFF
if state.gpOut[1].pwm == 1
M42 P1 S0
else
M42 P1 S1
in the video it looks like the fan shroud hits the bed before the nozzle. Also it goes way to slow to probe...
@ignacmc make sure your arms are set in couples and positive oposite to negative on the 6 magballs og the effector, also use nylon spacer and make sure the screws don´t touch the pcb...
on my pictures you can tell by the lenght stickers on the arms and no label on the others.
By doint this wou balance the magnetic fields, other than if you put all 6 positives on one side and all 6 negatives on the other side.
Don´t mind the "stickers" on the magball to arm joint section, it´s a 0.8mm ptfe film to lubriocate the joints
I would try at least one
@Fred-Y I use a ptfe foil to lubricate ball-arm joints.
@janjoh could you show us your setup? and how you manage to attach the accelerometer.
TIA
@Dizzwold why don´t you set up a range of operation
M106 P2 H2 L.3 B.5 X1 T40:65
Will start above 40ºC at 30% of the fan increasing to 100% proportionally until 65ºC is reached
B is 50% jump start
Just play with the T values as you wish
@Drak said in Part Cooling Fan Setup:
M950 F0 C"fan3" Q200 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off; Tools
M563 P0 D0 H0 F0 S"Main"
Try this better
