Duet 2 Wifi + BL-Touch doens´t work, no Trigger-Signal

JustD

Thank you for the Answers:

@Phaedrux I´m using the DWC Version 1.22.6 WiFi 1.22 FW 2.02
But I have values in the drop down List from 190 up to 285°C

@dc42.. thanks help al lot.

@Stephen6309 here my M143: M143 H1 S280 ; Set temperature limit for heater 1 to 280C

Sorry, I can´t insert a pic.. only a Link to a pic.. or.. How does it here work?

JustD

Phaedrux

@justd said in Duet 2 Wifi + BL-Touch doens´t work, no Trigger-Signal:

M143 H1 S280

You may need to set M143 slightly higher than your target temp to allow for some overshoot.

JustD

@Phaedrux, by the way --- the Problem with the BLTouch is solved.
My clone-BLTouch was defect.. now with the origin it works very fine.

OK.. You mean.. maybe 300°c where better?

JustD

What I have seen.. tested/messured...
My heatingblock, with the heating-patrone.. reach the abvised temperature... set 200° = 200° messured at the block.. but at the Nozzele at self.. there is only 166°c

Is that normal.. this big difference?

JustD

I have change my Heatingblock and the Nozzle.. and its much better.
I set 200°C and my Nozzle reach 194°C.. Thats Ok for me.

I Work around som smal issues.. retract and so on.. its much, much better than ever before..
Headbed.. I think I can sodl the silicon heater.. the objects hold very good with extrem low temp.. 30-40°.. ABS/PLA..
Above 60°C I can´t use it.. the grip is to extrem.. . need 30min. to loosen the object.. lol

I print with 60mm/sec.. for now it´s OK

But the bedleveling is one Issue what I have open.
I try with the WBC the Compensation.. but it seems very confused...and very extremly in reaktion of changing everything with bedleveling.
What ist he difference between

Meshcompensation and
Bedcompensation ??
At my Bedcompensation.. I Can´t define the Messurement-Area of testing.
The Definition of Meshcompensation don´t work on it.
The Bed dimensions are not the right ting.. in oder I start the bedcompensation, the wagon moves to the zero Point and the next messurement try to move out of the 0-X coordinate in Minus.??
And the point before the last point in the middle... is outside my bed definition in +x.. above 350??

Whats wrong at my printer or my definition?
Is it possible to define the bed compensation in the config?

JustD

What does it mean with this Warning??

"G32
Warning: 3/4/5-point bed compensation is deprecated and will be removed in a future firmware release. Please use G29 mesh bed compensation instead.
Bed equation fits points [10.0, 15.0, -0.136] [10.0, 325.0, -0.351] [335.0, 325.0, -0.666] [335.0, 15.0, 0.079] [175.0, 175.0, -0.528]"

JustD

OOh .. I´v got it.

Meshcompensation seems to work now..

matej1006

Hello

what did you do to solve this error
Warning: 3/4/5-point bed compensation is deprecated and will be removed in a future firmware release.

Matej

JustD

I´ve change my Configuration... like this Betrue3D.dk

Now it works with 3 Z-Axis and Meshkompensation
With my eyes.. perfekt!

If you want my config, let me know.