Pressure Advance Calibration

Munce31

Hi All

I've been using this python script to fine tune my pressure advance on my zesty nimble extruder. It has been a massive help in this process.

Just one suggestion - I don't know if it is possible - however, I would like to see what pressure advance setting it is currently at during the print. Preferably to be displayed like a pop, similar to how the Report PA macro works in https://forum.duet3d.com/topic/6181/tuning-macros-menus-accel-jerk-retraction-pressure-advance. Is it possible to add something to this python script to report current pressure advance? It would make fine tuning the pressure advance just a little easier by taking a chunk of the guess work out of it.

Thanks,
Vince

wilriker

@Munce31 You could manually add M117 <current PA value> into the GCode file after every change of PA.

Munce31

@wilriker said in Pressure Advance Calibration:

@Munce31 You could manually add M117 <current PA value> into the GCode file after every change of PA.

Yeah I figured I could do that as well, but that potentially could be quite laborious. I was thinking more along the lines of something like M117 <current PA value> being added directly into the python script so that it can be automated.

Phaedrux

The Report PA Value macro just sends the command for pressure advance without any parameters so that the current value gets echoed back. Doing a find and replace in the gcode file shouldn't be too hard to add it.

OBELIKS

@Munce31 If you are using the script @jens55 posted, you can add

print("M117 %.3f" % pressure_advance)

after

print("M572 D0 S%.3f" % pressure_advance)

Munce31

@OBELIKS said in Pressure Advance Calibration:

@Munce31 If you are using the script @jens55 posted, you can add
print("M117 %.3f" % pressure_advance)
after
print("M572 D0 S%.3f" % pressure_advance)

Hi @OBELIKS thanks for providing that. It'll make it easier to watch the test print and see what pressure advance it current is running at.

zzing

I was reading though some of this to take a look at my own values.

What is quite odd is that the point at which the fast areas and slow areas are equal in width is at 1.75 - which seems crazy high according to the documentation. I am using a bowden tube of capricorn of length ~600mm. It has a bondtech extruder and a smart effector/v6 combo on the output.

I was using the original script from the start.

The other relevant settings from config:

M92 X80.00 Y80.00 Z80.00 E830.00                  ; Set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E40.00             ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E5000.00        ; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z3000.00 E120.00            ; Set accelerations (mm/s^2)
M906 X1000.00 Y1000.00 Z1000.00 E500.00 I30        ; Set motor currents (mA) and motor idle factor in per cent

I also just figured out this:

M92 E820
M592 D0 A0.001246 B0.000406 T230

Do these seem reasonable? The max instanteous speed sounds low compared to one post above.

This is an upgraded mini kossel.

wilriker

@zzing said in Pressure Advance Calibration:

M566 X1200.00 Y1200.00 Z1200.00 E40.00             ; Set maximum instantaneous speed changes (mm/min)
Do these seem reasonable? The max instanteous speed sounds low compared to one post above.

These values really are rather odd. How did you find such a low max inst. speed value for E? I have mine at 1800 and think I am still rather on the low end. Also this 40 of yours will probably lower total print speed.

zzing

I am not sure if I set that or it was configured from the tool to build a config. With all those other values I could probably use realistic values for a delta machine.

I can retest then.

bot

If a user has a very geared down extruder, low E jerk is required (if using pressure advance). IIRC, extruder jerk is only used when pressure advance is in effect. Otherwise, it has no effect on print time. E Accel has an effect on print time when set too low, with or without pressure advance.

My extruder can't use correct amounts of pressure advance without a low E jerk value of ~90.

SnakeSP

I have very strange results when trying to calibrate PA.
Here are the speed, acceleration and jerk settings:
M203 X15000.00 Y15000.00 Z15000.00 E6000.00
M201 X2000.00 Y2000.00 Z2000.00 E2000.00
M566 X1200.00 Y1200.00 Z1200.00 E1200.00
I'm using BMG cloned extruder (if matters) with bowden of 550 mm and ID 2 mm.
Used python script to print patterns with the following settings:
extrusion_width = 0.5 (nozzle is 0.4 actually, 0.5 is used in slicer as an extrusion width)
layer_height = 0.2
filament_diameter = 1.72 (measured with calipers)

travel_speed = 150
first_layer_speed = 15
slow_speed = 5
fast_speed = 70

I tried PA settings from 0.1 to 1.0 at first and there were no signs of PA working. Further experiments showed that noticable result is there only in range 1.5 to 1.9. But this looks insane... Or this is normal?
Also i noticed that the speed is limited to 63-65 mm/s (due to too low extruder settings possibly?).

Phaedrux

@SnakeSP Perhaps try this method of tuning pressure advance.

https://duet3d.dozuki.com/Wiki/Pressure_advance#Section_Methods_of_finding_the_right_amount_of_pressure_advance

SnakeSP

@Phaedrux
I tried the first one, with the python script.
Will try the second one, with the cube, but need to understand how to make Simplify3d to align seam at the center of the side, for now i can only align it to one of the corners.

One more thing still bothers me: i have not yet found the proper settings for BMG extruder (speed, acceleration, jerk) there are very different number said to be best in every topic i've read and there is nothing about it on Bondtech site. Can you point me where can i find such info please?

SnakeSP

No matter what i try to set with "Choose start point..." the beginning of the line is always in the corner. Same for Cura. Does anyone know how to align Z seam to the center of the cube's side?

Phaedrux

@SnakeSP not sure about simplify but with Cura you choose it specified and then choose an x y coordinate for the seam.

SnakeSP

@Phaedrux
Yes, i tried that but Cura still places seam to the corner...

Phaedrux

@SnakeSP

Z seam alignment - User specified
Z seam position - back
Seam corner preference - none

Produces the desired result. That's in 4.4.1. In older versions there was an X and Y position you could specify. The setting is still there in the settings visibility filter, but it's not being shown and I'm not sure what's blocking it. Regardless, setting it to back, front, left, or right works to align it to a face.

SnakeSP

@Phaedrux
Does not work for me
Cura 4.4.1, settings as you've specified - seam is generated in one of the corners no matter what coordinates i set.
Can you share a gcode of the cube (20x20x20) with a single perimeter with a seam in the center of one of the sides so i can modify it for my printer, please?

burtoogle

@SnakeSP said in Pressure Advance Calibration:

@Phaedrux
Does not work for me
Cura 4.4.1, settings as you've specified - seam is generated in one of the corners no matter what coordinates i set.
Can you share a gcode of the cube (20x20x20) with a single perimeter with a seam in the center of one of the sides so i can modify it for my printer, please?

See https://forum.duet3d.com/post/124481

SnakeSP

@burtoogle Thanks!