Paneldue not allowing me to set temp on T2.
-
How many tool heaters are you using? Please share your config.g file.
-
I'm using 2 heaters. One for each head (IDEX).
How do I upload files on here?
-
@timcurtis67, there is an upload file button in the reply window (see icons above text you type)
-
config.g. is short enough that you can include the text in your post.
-
Config.g
; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware compatibility to look like RepRapFirmare; Endstops
; M558 P6 I1 X0 Y0 Z0 F175 T6000 H3 ; Probe Mode 6 Switch Type
; M558 P1 I1 R0.4 F300 X0 Y0 Z0 ; Piezo Board
G31 X0 Y0 Z6.975 ; Set Z probe offset and trigger height Switch Type
; G31 X0 Y0 Z-.1 P600 ; Piezo Board
M557 X-195:195 Y-190:190 S20 ; Define mesh grid; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S0 ; Drive 4 goes backwards
M569 P5 S0 ; Drive 5 goes backwards
M584 X0 Y1 Z2 U3 E4:5 ; Create U axis for second X carriage before we try to configure it
M574 X1 Y2 U2 Z2 S0 ; Set active low endstops
M208 X-255.3 Y-226 U-213 Z0 S1 ; Set axis minima
M208 X214 Y250.1 U255.6 Z426.95 S0 ; Set axis maxima
M350 X16 Y16 U16 Z16 E16:16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 U80 Z400 E837.0:837.0 ; Set steps per mm
M566 X175 Y175 U175 Z12 E500:500 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 U18000 Z2500 E1200:1200 ; Set maximum speeds (mm/min)
M201 X600 Y600 U600 Z250 E1000:1000 ; Set accelerations (mm/s^2)
M906 X1000 Y1400 U1000 Z1800 E1100:1100 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Heaters
M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning)
M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C0.0000000706 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S350 ; Set temperature limit for heater 1 to 350C
M305 P2 T100000 B4725 C0.0000000706 R4700 ; Set thermistor + ADC parameters for heater 2
M143 H2 S350; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 U0 Z-.25 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 X3 ; Define tool 1
G10 P1 X0 Y.1 U0 Z-.25 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C
M563 P2 D0:1 H1:2 X0:3 ; Define tool 2 Ditto Printing
G10 P2 X50 Y0 U-50 Z-.25 ; Set tool 2 axis Ditto Printing offsets
G10 P2 R0 S0 ; Set initial tool 2 active and standby temperatures to 0C
M576 P2 E1:1 ; Set mix rtio 100% on both extruders; Network
M550 P******* ; Set machine name
M551 ******* ; Set password
M552 S1 ; Enable network
M587 S"EnolaRoad" P"******" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Fans
M106 P1 S1 I0 F500 H1 T45; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H2 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P3 H100:101 T35:45 L0.3 ; CPU Cooler later; Custom settings are not configured
; Miscellaneous
M501 ; Load saved parameters from non-volatile memory
M80 ; turn on power supply
T0 ; Select first tool -
Here is my tfree2 and tpost2 files as well
; tfree2.g
; called when tool 0 is freed
;
; generated by RepRapFirmware Configuration Tool on Mon Nov 27 2017 08:32:27 GMT-0500 (Eastern Standard Time)M83 ; relative extruder movement
G91 ; relative axis movement
G1 Z5 F1500 ; up 10mm
G90 ; absolute axis movement
G28 X U ; park the X & U carriages
;M572 D0 S0.0
;M572 D1 S0.0; tpost2.g
; called after tool 0 has been selected
;
; generated by RepRapFirmware Configuration Tool on Mon Nov 27 2017 08:32:27 GMT-0500 (Eastern Standard Time); Wait for set temperatures to be reached
;G91
;G1 X1 F1500
;G1 Z-10 F1500
M116 P2
M567 P2 E1:1 ; Set mixing ratio
M568 P2 S1 ; turn on mixing
;M572 D0 S0.06 ; turn on pressure advance ext 1
;M572 D1 S0.06 ; turn on pressure advance ext 2 -
You have 3 tools configured but only 2 heaters. PanelDue doesn't yet handle multiple tools very well when there isn't a 1:1 mapping between heaters and tools.
-
Any suggestions on how to map the third heater? I just followed the guides for IDEX on the Duet documents page but didn't see anything about mapping an additional heater?
Please advise or point me in the right direction,Thank you David
-
Your tool configuration is correct, it's just that PanelDue doesn't handle the ditto printing tool properly.
-
Okay David, now I'm following you. Thank you for the info. It's not a big deal I just wanted to make sure I didn't miss something.
The new firmware is working great! I'm running 20 out of 24 hours per day for the next 10 days with the IDEX ditto printing. Thank you for all the amazing work you guys do with the Duet!
