Duet Wifi Webserver not responding

ShiftingTech

So, acknowledging that my issue may not be the same one being primarily discussed in this thread, I still think my issue is due some addressing as well. Would you like me to start a separate thread for it, or…?

dc42

If it's different symptoms then a separate thread would be better.

daveidmx

The full M122 output is at the bottom, but I picked out the socket status lines here. (I think there might be a threading bug in the new debug code because the output lines for socket status are interwoven through the entire M122 output.)

WiFi: Conn 0: aborted 80, 56749, 172.20.2.32
WiFi: Conn 1: aborted 80, 57066, 172.20.2.32
WiFi: Conn 2: aborted 80, 56482, 172.20.2.32
WiFi: Conn 3: aborted 80, 57367, 172.20.2.32
WiFi: Conn 4: aborted 80, 58524, 172.20.2.32
WiFi: Conn 5: aborted 80, 58528, 172.20.2.32
WiFi: Conn 6: aborted 80, 58814, 172.20.2.32
WiFi: Conn 7: aborted 80, 58821, 172.20.2.32

FWIW none of those port numbers show up in a netstat.exe dump from the client PC.

M122
=== Diagnostics ===
Used output buffers: 1 of 32 (13 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21RC5 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-95BNL-MGPSJ-6J1F6-3SS6L-T0XZZ
Static ram used: 16152
Dynamic ram uWiFi: Conn 0: aborted 80, 56749, 172.20.2.32
sed: 100824
Recycled dynamic ram: 1808
Stack ram used: 3576 current, 6512 maximum
Never used ram: 5776
Last reset 05:46:36 ago, cause: power up
Last software reset at 2018-03-15 20:27, reason: User, spinning module GCodes, available RAM 6944 bytes (slot 1)WiFi: Conn 1: aborted 80, 57066, 172.20.2.32

Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0041f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 372.6ms
MCU temperatureWiFi: Conn 2: aborted 80, 56482, 172.20.2.32
: min 39.5, current 42.9, max 45.5
Supply voltage: min 23.8, current 24.1, max 24.5, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max 0/193
Driver 1: ok, SG min/max 0/1023
Driver 2: standstill, SG min/max not available
DriveWiFi: Conn 3: aborted 80, 57367, 172.20.2.32
r 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max 0/216
Driver 6: standstill, SG min/max 0/222
Driver 7: standstill, SG min/max 0/219
Driver 8: standstill, SG min/max 0/205
Driver 9: standstill, SG mWiFi: Conn 4: aborted 80, 58524, 172.20.2.32
in/max not availablWiFi: Conn 5: aborted 80, 58528, 172.20.2.32
e
Expansion motor(s) stall indication: yes
Date/time: 2018-03-17 18:18:45
Slowest main loop (seconds): 0.374137; fastest: 0.000050
=== Move ===
MaxReps: 4, StepErrors: 0, LaErrors: 0, FreeDm: 222, MinFreeDm 150, MaxWait: 5190120ms, UnderWiFi: Conn 6: aborted 80, 58814, 172.20.2.32
runs: 0, 1
Scheduled moves: 833, completed moves: 826
Bed compensation in use: none
Bed probe heights: -0.064 -0.078 -0.086 -0.077 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0WiFi: Conn 7: aborted 80, 58821, 172.20.2.32
.5
=== GCodes ===
Segments left: 1
Stack records: 4 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X111.412 Y110.526 E0.43514" in state(s) 0
serial is ready with "M122" in state(s) 0WiFi:

aux is idle in state(s) 0
daemWiFi: xmit: 0
on is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiWiFi: recv: 0
Fi -
Network state is running
WiFi module is connected to access poWiFi: fw: 0
int
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21RC5(16b1)
WiFi MAC address 2c:3a:e8:0a:fb:70
WiFi Vcc 3.40, reset reason Turned on by main processor
WiFi flaWiFi: drop: 0
sh size 4194304, free heap 14712
WiFi IP address 172.20.2.17
WiFi signal strength -53dBm, reconnections 0WiFi: chkerr: 0
, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Expansion ===
DueX I2C errors 0
ok
WiFi: lenerr: 0
WiFi: memerr: 0
WiFi: rterr: 0
WiFi: proterr: 0
WiFi: opterr: 0
WiFi: err: 0
WiFi: cachehit: 0
WiFi:
WiFi: xmit: 12
WiFi: recv: 13
WiFi: fw: 0
WiFi: drop: 2
WiFi: chkerr: 0
WiFi: lenerr: 0
WiFi: memerr: 0
WiFi: rterr: 0
WiFi: proterr: 2

dc42

Thanks, that's helped me to pin down a problem with error recovery. Please try the new main firmware at https://www.dropbox.com/s/iq9pzfaugyfei7x/Duet2CombinedFirmware.bin?dl=0.

daveidmx

Installed. Will report back.

daveidmx

I've done a few prints today without seeing the symptoms. Watching the console for a while showed connections on socket 0 and 1 after a few hours (even returning to 0 after being on 1 for a while) where yesterday this would climb incrementally up to 7 and then fail. Based on those two things, I'd tentatively say this seems to have resolved the issue.

dc42

Thanks for the feedback. This fix will go live in firmware 1.21.

daveidmx

Sounds good. Thanks for looking in to this!

dc42

@daveidmx:

Sounds good. Thanks for looking in to this!

Thanks for providing the critical data!

guycobb2

I'm experiencing the same issue. It seems to be resolved…... correct? If so, what firmware should I install?