reference the X-axis on both rails

axiom

@fcwilt I understand that, this is for the Enstops...but what do I write for the capacitive sensor for the Meshbed compensation?

fcwilt

@axiom

As mentioned the configuration of the Z probe does not change.

What you have to do is include the commands that tell the firmware how to create the height map

M557

Xaaa:bbb : Minimum and maximum X coordinates to probe
Yaaa:bbb : Minimum and maximum Y coordinates to probe
Pxx:yy : Number of points on X axis, number of points on Y axis

So for example let's say the min/max limits of your bed on the X axis is -150 to 150 and on the Y axis -100 to 100. I always place X=0 and Y=0 at the center of the bed so the min/max limits are as you see.

Now you have to determine where in that area your probe can reach - this is determined by the X and Y offsets of the probe and the possible range of motion outside of the min/max limits.

So let's assume your probe has an X offset of 0 and a Y offset of +25.

Let us also assume your probe can reach from -150 to +150 on the X axis and from -90 to +100 on the Y axis.

You could have an M557 like this:

M557 X-150:150 Y-90:150 P20:15

Which means the mesh would have 20 points along the X axis and 15 points along the Y axis, for a total of 300 points. And the mesh would span from -150 to 150 on the X axis and from -90 to +100 on the Y axis.

So to create the height map you would:

Move to Z=5
Move the probe to the center of the bed, taking into account the probe offset in Y
Execute a G30 to set the Z=0 Datum
Execute a G29 S0 to probe the bed and create the height map

Feel free to ask any questions.

Frederick

axiom

@fcwilt Can I also place the Z-probe 10mm below the nozzle and then still move the bed closer to the head...if so, where and how can I enter this in the code?

axiom

@fcwilt Sorry, I don't mean the probe but the endstops

fcwilt

@axiom

Yes - the "flag" that you fashion to slide into the slot and break the beam can travel beyond the slot if needed.

You want the position of the sensors to be easily adjustable so you can get them in the same position - or as near as possible.

When you execute a G1 move with the H1 parameter the movement stops when the associated endstop sensor is triggered and the logical position of the axis is set to the min/max value as specified in M208. The M574 command that configures the endstop specifies if it is at the "high" end or the low "end" of the axis, thus determining if the max value from M208 is used or the min value.

Your Z min value is likely to be 0. But if your endstops trigger at, say, 10mm away from 0, you have a disconnect between the physical Z position (-10) and the logical Z position (0).

That is easily dealt with. After the G1 H1 command that does the homing just add a G92 Z### where ### is the actual physical position on the Z axis (-10 in the example above). Now the logical and physical positions will be in sync at -10 and then you can move Z to physical 0.

Hope that clears things up.

Frederick

axiom

@fcwilt So I connected the probe to test it and tried it out successfully.

The problem is that the Z axis does not stop when the end stop is triggered manually but only when the probe is triggered. But I would like to use the end stops for stopping and the probe only for mesh bed compensation. Here my code:

; Endstops
M574 X1 S1 P"xstop + e0stop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop

; Z-Probe
M558 K0 P1 C"!zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds (Kapazitiver Sensor)
M557 X0:735 Y-27:573 S35 ; define mesh grid

fcwilt

@axiom

Do you have anything else in the config.g file that is already using the "zstop" input?

Errors like that don't show up when you boot (or re-boot) the printer.

Once up and running you can execute from the DWC console M98 P"config.g" and you may see error messages.

And remember to use G32 to do auto bed leveling you will need 4 Z axis endstops and thus 4 unused inputs.

Frederick

axiom

@fcwilt said in reference the X-axis on both rails:

M98 P"config.g"

I don't have any error messages. However, it doesn't stop at the z endstop but only at the probe... I'm happy with it. It is clear to me that I will need 4 endstops and 4 motor drivers later. This is about the test...but my Z-endstop should work here too. Here is the whole code again
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sun May 28 2023 15:23:44 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"DUKA1300" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S1 ; enable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0 ; physical drive 3 goes forwards
M584 X0:4 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z640 E322.58 ; set steps per mm
M566 X900.00 Y900.00 Z100.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z40.00 E250.00 ; set accelerations (mm/s^2)
M906 X1800 Y1800 Z1800 E1600 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X100 Y0 Z0 S1 ; set axis minima
M208 X750 Y640 Z1220 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop + e0stop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S1 P"e1-stop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop

; Z-Probe
M558 K0 P5 C"!zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds (Kapazitiver Sensor)
M557 X0:735 Y-27:573 S35 ; define mesh grid

; Heaters

; Bed
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.283 K0.463:0.000 D7.17 E1.35 S1.00 B0 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S280 ; set temperature limit for heater 0 to 120C

;Hotend
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 R1.797 K0.742:0.000 D7.57 E1.35 S1.00 B0 V23.8 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S400 ; set temperature limit for heater 1 to 400C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F2 C"fan2" Q350 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1 T60 ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 1
G10 P0 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P0 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

; Filamentsensor
;M591 D0 P1 C"e1-stop" S1 ;R40:120 E3.0 S1 Filament Sensor

;Auto Z-Offset
; Custom settings are not defined
M501

fcwilt

@axiom

I don't see anything there in the config.g.

When testing the Z endstop you are doing a G1 H1 Znnn move?

If the endstop switch is not working then that would seem to leave only a hardware problem - defective switch, incorrect wiring.

You are using firmware 3.3.

That has the Object Model Browser doesn't it?

If so, you can use that to look at the Z endstop state and see if it changes with the state of the Z endstop switch.

Frederick

axiom

@fcwilt I test the endstop with the homing function

axiom

@fcwilt I tried the endstop before on the y-axis and it worked there...so the wiring/plugs and the function of the endstop are no longer necessary

axiom

@fcwilt Ok...with G1 H1 Z0 it works...homing is probably reserved for the probe

fcwilt

@axiom said in reference the X-axis on both rails:

with G1 H1 Z0 it works...homing is probably reserved for the probe

When testing it is usually best to use the smallest bit of code that will do the job, thus the question about G1 H1.

Please post your homing files.

Frederick

axiom

@fcwilt Ok here they are:
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sun May 28 2023 15:23:44 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-755 Y-643 F1500 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-755 Y-643 F360 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X10 Y10 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sun May 28 2023 15:23:44 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-755 F1500 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X5 F6000 ; go back a few mm
G1 H1 X-755 F360 ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sun May 28 2023 15:23:44 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Y-643 F1500 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000 ; go back a few mm
G1 H1 Y-643 F360 ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sun May 28 2023 15:23:44 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G90 ; absolute positioning
G1 X1 Y61 F6000 ; go to first probe point
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

fcwilt

@axiom

Thanks.

As I expected homing of Z is being done with the probe.

Once you have the Z endstop sensor (or multiple sensors) in place you can use them instead of the Z probe to home the Z axis.

It will make the homing a bit simpler.

Just FYI.

I don't like having actual homing code in homeall.g.

I simply have this:

M98 P"homeZ.g"
M98 P"homeX.g"
M98 P"homeY.g"

Remember that I always install Z endstop sensors on my printers so I can home Z first. Also I don't use the Z probe during homing at all, it is not necessary.

Yes, by putting actual homing code in homeall.g you can optimize things slightly but I don't consider it worth it for the added complexity of having essentially duplicate code in two places.

Frederick

axiom

@fcwilt What do I have to write into the Homing.g files instead of the G30 command?

axiom

@fcwilt or to put it another way...if I delete homeall.g, how do I correct homez.g?

fcwilt

@axiom

Do you have the Z endstop sensor installed and ready to use? Good job.

OK as to the code...

Basically you use the same sort of G1 H1 commands that you do with X and Y axes.

The three files homeX.g, homeY.g and homeZ.g could end up looking pretty much the same.

To provide example code let's assume that all three axes home to the axis minimum. Let's also assume that the range of motion on each axis is a total of 300mm. The essential code would look something like this:

In homeX.g:

G91               ; relative moves
G1 H1 X-310 F6000 ; fast move to min endstop
G1 X20            ; back off a bit
G1 H1 X-25 F600   ; slow move to min endstop
G92 X###          ; where ### is the actual axis position when the motion stopped - usually determined by testing

In homeY.g:

G91               ; relative moves
G1 H1 Y-310 F6000 ; fast move to min endstop
G1 Y20            ; back off a bit
G1 H1 Y-25 F600   ; slow move to min endstop
G92 Y###          ; where ### is the actual axis position when the motion stopped - usually determined by testing

In home Z.g:

G91               ; relative moves
G1 H1 Z-310 F1200 ; fast move to min endstop
G1 Z20            ; back off a bit
G1 H1 Z-25 F300   ; slow move to min endstop
G92 Z###          ; where ### is the actual axis position when the motion stopped - usually determined by testing

Regards the G92 commands:

Remember that the G1 H1 moves stop when the endstop is triggered and the logical axis position is set to the min/max value from the M208 for that axis, depending on the configured location of the endstop.

But if your endstops don't actually trigger at exactly the min/max position (mine never do) then you can use G92 so the logical position of the axis (which G92 sets) is in sync with the physical position.

Hope that helps rather than confuses.

Frederick

axiom

@fcwilt Thank you very much first of all... now I have to wait until the expansion board arrives (hopefully this week)... only then can I try it out and then report back... have a nice Sunday!
Cheers,
Don

fcwilt

@axiom

If I cannot help I am always happy to confused.

I just noticed a mistake in my example code the F letter was missing from the slow moves speed setting. I just corrected them.

Frederick