Emergency reset
-
i was about 3hrs in a print job, when i made an adjustment to the speed factor. at that moment, i was shown a message that the emergency stop had been activated. here is the m122 file
, i am still running 1.19.2 because it seemed like the newer versions were plagued with reset, disconnects, and ajax problems. Do i need to bite the bullet and upgrade to the latest and greatest versionsM122
=== Diagnostics ===
Used output buffers: 3 of 32 (5 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19.2 running on Duet WiFi 1.0
Board ID: 08DAM-9K9K2-NGNS0-7JTD2-3S46M-KP2RJ
Static ram used: 21176
Dynamic ram used: 96032
Recycled dynamic ram: 1576
Stack ram used: 1304 current, 4880 maximum
Never used ram: 7408
Last reset 00:00:53 ago, cause: software
Last software reset reason: User, spinning module GCodes, available RAM 3192 bytes (slot 4)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 44.0, current 45.1, max 45.6
Supply voltage: min 12.4, current 12.5, max 12.6, under voltage events: 0, over voltage events: 0
Driver 0: stalled standstill
Driver 1: stalled standstill
Driver 2: standstill
Driver 3: stalled standstill
Driver 4: standstill
Date/time: 2017-12-06 10:27:05
Slowest main loop (seconds): 0.005385; fastest: 0.000034
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = -1, chamber heater = -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
WiFi firmware version 1.19.2
WiFi MAC address 5c:cf:7f:f7:de:c3
WiFi Vcc 3.16, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 39616
WiFi IP address 10.0.0.61
WiFi signal strength -50dBm
Reconnections 0
HTTP sessions: 1 of 8
Socket states: 2 0 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) -
I'm sorry you lost your print. Were you adjusting the speed factor from DWC, PanelDue, or some other input?
-
The 1.20beta11 build is solid, have no fear - upgrade.
-
m sorry you lost your print. Were you adjusting the speed factor from DWC, PanelDue, or some other input?
Quote Answer Report
I was using DWC to increase the speed 10% faster. The other strange thing that it has done since there 1.19 upgrade, is when I make a change to the config.g file, it asked if I want to reboot, when I do, I get a Ajax error and I have to reconnect. It really isn't an issue, but just something new.
