Configuring TriangleLab R100 3950k thermistor - have datasheet
-
I can't figure out if I need additional parameters to my M305 for some cartridge thermistors I have. My current setting is M305 P2 H0 T100000 B3950 ; but I read in old threads that this type of thermistor may need a C value set, but I couldn't find the calculator in the reprap firmware wizard.
The documentation for the thermistor can be found here; https://trianglelab.net/u_file/2203/02/file/NTC100KB3950-1-2c16.pdf
And it specifies a maximum value of 0.141 ohms at 300c. Is there a way to enter a specific temperature / ohms reading as a parameter?
-
@mortarart said in Configuring TriangleLab R100 3950k thermistor - have datasheet:
I can't figure out if I need additional parameters to my M305 for some cartridge thermistors I have. My current setting is M305 P2 H0 T100000 B3950 ; but I read in old threads that this type of thermistor may need a C value set, but I couldn't find the calculator in the reprap firmware wizard.
The documentation for the thermistor can be found here; https://trianglelab.net/u_file/2203/02/file/NTC100KB3950-1-2c16.pdf
And it specifies a maximum value of 0.141 ohms at 300c. Is there a way to enter a specific temperature / ohms reading as a parameter?
Yes, choose the Custom thermistor option in configtool, then enter three temperature/resistance pairs in the popup calculator.
-
@mortarart There's a couple of ways you can do this. In the RRF configuration tool, click on the R (resistance), Beta or C parameter box to open the Calculate Heater Parameters pop-up, and select 'Custom' to put in your own values for resistance at particular temperatures. The thermistor parameters will be calculated from these.
Alternatively, or as a check, you can use the SRS Thermistor Calculator
You can see the results above. The Steinhart-Hart model should be more accurate than the Beta model. The SRS Thermistor Calculator calculates the S-H model slightly differently (using A and B parameters rather than R25 and Beta), but the C parameter is the same, so looks about right to me.
Ian
TronXY X5S with Duet 3 MB6HC and Roto toolboard : Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : Polargraph with Duet 2 WiFi
-
@droftarts said in Configuring TriangleLab R100 3950k thermistor - have datasheet:
The SRS Thermistor Calculator calculates the S-H model slightly differently (using A and B parameters rather than R25 and Beta), but the C parameter is the same, so looks about right to me.
When using a C parameter, the B value you need for RRF in M305 or M308 is the reciprocal of the B value given by the SRS calculator, not the Beta value.
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
When using a C parameter, the B value you need for RRF in M305 or M308 is the reciprocal of the B value given by the SRS calculator, not the Beta value.
@dc42 Thanks for the clarification! I'd forgotten how to go between the two.
@MortarArt e.g.: 1 / 0.0002324878438 = 4301 which is the value the RRF configuration tool gives for the B parameter.
Use M308 if you are using RRF 3.x. M305 is for RRF 1.x and 2.x, and is deprecated in 3.x.
Ian
