Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    FAN 0 & FAN 1 allways ON

    Scheduled Pinned Locked Moved
    General Discussion
    5
    31
    1.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • CozyPundefined
      CozyP @fcwilt
      last edited by

      @fcwilt

      hELLO

      I updated fan 2.

      However I haven't managed to make fan 1, which is the extruder cooler fan stop and turn on when the heater turns on.

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
      M143 H1 S280 ; set temperature limit for heater 1 to 280C
      M308 S10 Y"mcu-temp" A"MCU" ; defines sensor 10 as MCU temperature sensor
      M308 S11 Y"drivers" A"Duet stepper drivers" ; defines sensor 11 as stepper driver temperature sensor

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
      M950 F2 C"fan2" Q100 ; create fan 2 on pin fan2 and set its frequency
      M106 P2 H10:11 T40:70 ; set fan 2 value

      fcwiltundefined 1 Reply Last reply Reply Quote 0
      • fcwiltundefined
        fcwilt @CozyP
        last edited by

        @cozyp

        If configure that fan to non-thermostatic control can you then set it's speed using it's DWC fan speed slider?

        Frederick

        Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

        CozyPundefined 1 Reply Last reply Reply Quote 0
        • Phaedruxundefined
          Phaedrux Moderator
          last edited by

          Or send M106 P1 S1 H-1 That should turn it on full blast.

          Z-Bot CoreXY Build | Thingiverse Profile

          CozyPundefined 1 Reply Last reply Reply Quote 0
          • CozyPundefined
            CozyP @fcwilt
            last edited by

            @fcwilt I have connected this fan in the non PWM fan output

            fcwiltundefined 1 Reply Last reply Reply Quote 0
            • CozyPundefined
              CozyP @Phaedrux
              last edited by

              @phaedrux That's the problem. The extruder fan, NOT the part cooling fan is running full blast. Allways. Usually these fans turn on after T45celcius automatically

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator
                last edited by

                Sorry, can you clarify which fan is connected where?

                What happens when you send M106 P1 S1 H-1 ?

                Z-Bot CoreXY Build | Thingiverse Profile

                CozyPundefined 1 Reply Last reply Reply Quote 0
                • fcwiltundefined
                  fcwilt @CozyP
                  last edited by

                  @cozyp said in FAN 0 & FAN 1 allways ON:

                  @fcwilt I have connected this fan in the non PWM fan output

                  Sorry but I don't understand what you mean by that.

                  I was wanting you to verify that whatever output you were using was still working.

                  Frederick

                  Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                  1 Reply Last reply Reply Quote 0
                  • CozyPundefined
                    CozyP @Phaedrux
                    last edited by

                    @phaedrux @fcwilt

                    Ok. First things first.

                    Phaedrux, I sent M106 on config file. Nothing changed. Fan stays ON no matter what. FAN 1 was added as option on DWC screen, but it cannot be controlled, which is correct, as the fan is connected in a non PWM output.

                    dcwilt, the extruder heater fan and the motherboard fan are connected in a NON PWM output, but they allways stay ON, full blast no matter what....
                    I wanted to turn them on via thermostat, as they should work. Am I missing something???

                    ; Fans
                    M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                    M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
                    M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                    M106 M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned on
                    M950 F2 C"fan2" Q100 ; create fan 2 on pin fan2 and set its frequency
                    M106 P2 H10:11 T40:70 ; set fan 2 value

                    CozyPundefined Phaedruxundefined fcwiltundefined 3 Replies Last reply Reply Quote 0
                    • CozyPundefined
                      CozyP @CozyP
                      last edited by

                      ; Heaters
                      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
                      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
                      M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
                      M140 H0 ; map heated bed to heater 0
                      M143 H0 S120 ; set temperature limit for heater 0 to 120C
                      M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
                      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
                      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                      M143 H1 S280 ; set temperature limit for heater 1 to 280C
                      M308 S10 Y"mcu-temp" A"MCU" ; defines sensor 10 as MCU temperature sensor
                      M308 S11 Y"drivers" A"Duet stepper drivers" ; defines sensor 11 as stepper driver temperature sensor

                      ; Fans
                      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                      M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
                      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                      M106 M106 P1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
                      M950 F2 C"fan2" Q100 ; create fan 2 on pin fan2 and set its frequency
                      M106 P2 H10:11 T40:70 ; set fan 2 value

                      ; Tools
                      M563 P0 D0 H1 F0 ; define tool 0
                      G10 P0 X-15 Y-15 Z0 ; set tool 0 axis offsets
                      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator @CozyP
                        last edited by

                        @cozyp said in FAN 0 & FAN 1 allways ON:

                        Phaedrux, I sent M106 on config file. Nothing changed. Fan stays ON no matter what.

                        Yes, M106 P1 S1 H-1 will disable thermostatic control and turn the fan on. Send M106 P1 S0 to turn it off again.

                        @cozyp said in FAN 0 & FAN 1 allways ON:

                        FAN 1 was added as option on DWC screen, but it cannot be controlled, which is correct, as the fan is connected in a non PWM output.

                        Fan1 port is indeed PWM controllable.

                        Fan0, Fan1, Fan2 are controllable. Plus two more always on fan ports.

                        Which are you actually plugged into?

                        Fan0 1 2 can be used as thermostatically controlled or by the slicer to set speed for part cooling.

                        The always on ports are... always on.

                        9a60778a-8b6e-46d6-999b-d996f9c4e4e6-image.png

                        If you send M106 P1 S0 and the fan won't turn off, then either it's plugged into a different port than you are expecting, or the fan mosfet has been damaged and failed in the on position.

                        Z-Bot CoreXY Build | Thingiverse Profile

                        1 Reply Last reply Reply Quote 0
                        • fcwiltundefined
                          fcwilt @CozyP
                          last edited by

                          @cozyp said in FAN 0 & FAN 1 allways ON:

                          dcwilt, the extruder heater fan and the motherboard fan are connected in a NON PWM output, but they allways stay ON, full blast no matter what....
                          I wanted to turn them on via thermostat, as they should work. Am I missing something???

                          It sounds like you are referring to the "always on" fan outputs - they are not controllable.

                          Frederick

                          Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                          1 Reply Last reply Reply Quote 0
                          • CozyPundefined
                            CozyP
                            last edited by

                            I have plugged those two fans on the allways ON ports.
                            So, after reading your comments, I assume that they cannot be thermostatically controlled???

                            fcwiltundefined 1 Reply Last reply Reply Quote 0
                            • fcwiltundefined
                              fcwilt @CozyP
                              last edited by

                              @cozyp said in FAN 0 & FAN 1 allways ON:

                              I have plugged those two fans on the allways ON ports.
                              So, after reading your comments, I assume that they cannot be thermostatically controlled???

                              They cannot be controlled in any way. They provide power to the connected fans when power is supplied to the board.

                              Frederick

                              Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                              1 Reply Last reply Reply Quote 0
                              • First post
                                Last post
                              Unless otherwise noted, all forum content is licensed under CC-BY-SA