RRF Update to 3.3 just killed my FW
-
@andy-cohen Yup!
All seems to be working fine for now.
I'm really not looking forward to updating my Toolchanger! -
This post is deleted! -
@andy-cohen This update FUBARED my machine. WHY was SO much changed?
Now I cannot control the tool from the PanelDue. I get constant messages about commands that no longer work WTF!
The tool definition makes no sense at all to me!
I cannot see how the Extruder is associated with the tool AT ALL!!! -
@andy-cohen said in RRF Update to 3.3 just killed my FW:
M563 P1 ; Define tool 1
This tool has no extruder or heater assigned to it. Perhaps that's your issue? You didn't mention which tool you're trying to control.
Can you share a recent config.g?
PanelDue is up to date now? DWC is at 3.3 as well?
-
@phaedrux When I try to retract at the hotend from the panel it does nothing. Then the panel becomes unresponsive. I cannot believe how frustrating this is! Why so many changes?
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jan 31 2022 16:37:49 GMT-0800 (PST); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name; Network
M550 P"CloneDuet" ; Set machine name
M551 P"adc238" ; Set password
M552 S1 ; Enable network
;M587 S"ATT642_EXT" P"4269605351" ; Configure access point. You can delete this line once connected
M587 S"ATT642" P"4269605351" ; Configure access point. You can delete this line once connectedM575 P1 B57600 S1 ;Paneldue
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
M669 K1 ; switch to CoreXY mode
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X88.57 Y88.57 Z400.00 E125.459271 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z400 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y195 Z210 S0 ; set axis maxima; Endstops
M574 X2 S1 P"!xstop" ; configure switch-type (e.g. microswitch) endstop for high end on X via pin xstop
M574 Y2 S1 P"!ystop" ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin ystop
M574 Z1 S1 P"!zstop" ; configure switch-type (e.g. microswitch) endstop for low end on Z via pin zstop; Z-Probe
M558 P1 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X10:300 Y-16.0:195 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M307 H0 B0 R0.219 C409.3 D5.09 S1.00 V23.7 ;From auto tune
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M307 H1 B0 R2.422 C201.2 D10.87 S1.00 V24.0 ;From Auto tune
M143 H1 S280 ; set temperature limit for heater 1 to 280C; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 ; Define tool 1
G10 P1 X35 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C; Custom settings are not defined
-
How many tools do you have? one or two?
Can you share your config from RRF2?I understand you're frustrated, but it's really not as devastating and you're making it out to be. Answer my questions and we'll get you back up and running.
The upgrade isn't forced and you can go back if you wish.
-
@phaedrux I have one. The code there is taken from the old config. When I put in what came out of the web app it does not work at all.
This is what was generated by the web app:
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C -
@andy-cohen said in RRF Update to 3.3 just killed my FW:
M563 P1 ; Define tool 1
G10 P1 X35 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0CIf you only have a single tool remove this section for tool1 then.
Does the extruder move when at temp?
@andy-cohen said in RRF Update to 3.3 just killed my FW:
I get constant messages about commands that no longer work WTF!
Can you be more specific? What do the messages actually say? What commands?
Can you confirm that the PanelDue is up to date now by checking it's version on the setup page?
-
@phaedrux OK... I will rem those lines out.
The messages were as follows:
"Error Tool 0 not found"
"Error: Attempting to Extrude with no tool selected"
There were more but I lost them. -
@phaedrux I remmed out the lines and rebooted.
The PanelDue shows the extruder icon with a Zero next to it(it used to show a "1").
I set the temp and heat it up. I select the Icon button so it's highlighted and I then go to the button to extrude some filament and hit extrude and nothing happens -
Can you add
T0to the end of your config.g so that the first tool is selected at startup? -
Can you send M98 P"config.g" and post the results?
-
@phaedrux said in RRF Update to 3.3 just killed my FW:
Can you send M98 P"config.g" and post the results?
The T0 on the last line is a good idea. I have that on my TC config. Trying now.Date Event
2/1/2022, 6:51:28 PM M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled -
@phaedrux So it will now extrude on command using the Extrude dialog on the PanelDue. Why it would not manually select IO have no clue, but the highlight on the button went on when selected.
BTW I was able to capture the message that flys by. Turns out it repeats over and over...
"Warning: Obsolete use of S parameter on G1 command. Use H parameter instead"
Looks like a good clue! -
@phaedrux It's not coming from my start gcode as far as I can see...?
"
; ****DuetClone start.gcode ****
G28 ; home all axes
;G29 S1 ; Use the Z offset Mesh Map on the SD card
M140 S[bed0_temperature] ; Heat buildplateG1 X0 Y0 Z10 F9000 ; Move to wait position off table
M190 S[bed0_temperature] ; Stabilize bed temperature
G10 P0 S[extruder0_temperature] R[extruder0_temperature] ; Set tool 0 operating and standby temperatures
M109 S[extruder0_temperature] ; set extruder temp and wait
start of purge line
G1 X40 Y5.5 Z0.2 F600.000 ; Extruder Prime Dry Move
G1 X250 Y5.5 Z0.2 F600.000 E25.000 ; Extruder Prime Start
G92 E0 ; Zero extruders
; **** end of start.gcode **** -
@andy-cohen said in RRF Update to 3.3 just killed my FW:
"Warning: Obsolete use of S parameter on G1 command. Use H parameter instead"
It's your homing files.
-
@phaedrux OK... so I swap out the S with an H?
Seriously... that was changed?
I'm finally printing...
But...
the message seems to be popping up from the G1 commands generated by my slicer; Simplify3D. I do not see anything in S3D's setup which can change that. -
@andy-cohen I might be incorrect on that. The messages have stopped. It could have all come from the homing scripts.
So...
Where else can I expect changes???
This was the "easy" machine to update. I did this update as a "practice" for the update of my Toolchanger. -
@andy-cohen The messages were from the homing scripts.
Just printed a perfect cal cube. Thanks for all your help and especially your patience. I'll be sure to do a shout out to you (well... your online handle at least) on the podcast. Without your help (and the others here) I do not think I would have figured it out. -
The S/H change was to become compatible with laser engraving software which uses G1 S for laser power. Easier to change the homing modifier than try to convince laser software makers to change their gcode.
You can find an example tool changer config for RRF3 here
https://github.com/Duet3D/RRF-machine-config-files/tree/master/E3D_Tool_Changer/dc42-duet3-centreZero-2Titan-2HemeraYou can get a handle on what's changed here: https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview
