Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    M540 and MAC address problems on Duet 3

    Scheduled Pinned Locked Moved Solved
    Using Duet Controllers
    3
    18
    463
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • sergioundefined
      sergio
      last edited by

      Hi,

      I have an issue with Duet 3 Ethernet. I have two machines that report the same address BE:62:38:3A:53:37 and i get a conflict on my network.

      I tried different formats:

      M540 PDE:AD:BE:EF:CA:FE
      M540 P0xDE:0xAD:0xBE:0xEF:0xCA:0xFE

      I test using arping and I can see the MAC addresses changing on the Duet 2 - Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.2 (2021-01-05)

      But Board: Duet 3 MB6HC (MB6HC)
      Firmware: RepRapFirmware for Duet 3 MB6HC 3.3RC1 (2021-05-01)
      doesn't seem to be changing with the same config/code.

      M540 reports correctly the new MAC address specified on the M540, but arping reports the original interface.
      It doesn’t seem to change. I have around 20 Duet 2 printers that can change the MAC correctly in but firmware 3.3 doesn't seem to work.

      G90
      M83
      M550 P"AM_NAME"
      M540 PDE:AD:BE:EF:CA:FE
      M552 P192.168.102.101
      M554 P192.168.0.1
      M553 P255.255.0.0
      M586 P0 S1
      M586 P1 S1
      M586 P2 S1
      M552 S1

      This is my config start setup, any recommendation?
      Best

      T3P3Tonyundefined sergioundefined 2 Replies Last reply Reply Quote 0
      • T3P3Tonyundefined
        T3P3Tony administrators @sergio
        last edited by

        @sergio are you using the Duet 3 in stand alone mode or SBC mode?

        I don't think it will be firmware related but I notice you are on 3.3RC1, can you try 3.3 stable as well please

        www.duet3d.com

        sergioundefined 1 Reply Last reply Reply Quote 0
        • sergioundefined
          sergio @sergio
          last edited by

          More tests, updated firmware to 3.4 Beta 4

          Board: Duet 3 MB6HC (MB6HC)
          Firmware: RepRapFirmware for Duet 3 MB6HC 3.4.0beta4 (2021-09-27)

          Turned off network before changing MAC
          M552 S0
          M540 P00:AD:BE:EF:CA:00
          M552 P192.168.102.101
          M554 P192.168.0.1
          M553 P255.255.0.0
          M552 S1

          Stills gives:
          Unicast reply from 192.168.101.121 [BE:62:38:3A:53:37] 0.994ms

          Second duet in conflict:
          Unicast reply from 192.168.102.105 [BE:62:38:3A:53:37] 1.384ms

          M540 gcode returns the right MAC, but it doesn't seem to be propagated to layer 2.

          1 Reply Last reply Reply Quote 0
          • sergioundefined
            sergio @T3P3Tony
            last edited by

            @t3p3tony

            Will try 3.3 stable, and it is stand alone.
            We use it pretty much as a duet 2.

            dc42undefined T3P3Tonyundefined 2 Replies Last reply Reply Quote 0
            • dc42undefined
              dc42 administrators @sergio
              last edited by

              @sergio please run M122 on each of those 2 Duets and post the result.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              sergioundefined 1 Reply Last reply Reply Quote 0
              • T3P3Tonyundefined
                T3P3Tony administrators @sergio
                last edited by

                @sergio I can reproduce this.

                from start on my test board:

                M540
MAC: be:62:3b:3a:53:32

                M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0beta4+1 (2021-10-04 17:49:00) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956L2-G43S8-6JKD0-3S46T-9U2YF
Used output buffers: 1 of 40 (15 max)
=== RTOS ===
Static ram: 151104
Dynamic ram: 97260 of which 12 recycled
Never used RAM 102296, free system stack 200 words
Tasks: NETWORK(ready,19.3%,249) ETHERNET(notifyWait,0.1%,173) HEAT(notifyWait,0.0%,273) Move(notifyWait,0.0%,351) CanReceiv(notifyWait,0.0%,797) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,339) TMC(notifyWait,8.4%,92) MAIN(running,48.3%,943) IDLE(ready,23.9%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:41 ago, cause: software
Last software reset at 2021-10-06 10:57, reason: User, GCodes spinning, available RAM 102296, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 128
MCU temperature: min 36.3, current 36.6, max 37.6
Supply voltage: min 23.7, current 23.8, max 23.8, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: pos 0, standstill, SG min/max 0/0, reads 39502, writes 11 timeouts 0
Driver 1: pos 0, standstill, SG min/max 0/0, reads 39502, writes 11 timeouts 0
Driver 2: pos 0, standstill, SG min/max 0/0, reads 39499, writes 14 timeouts 0
Driver 3: pos 0, standstill, SG min/max 0/0, reads 39502, writes 11 timeouts 0
Driver 4: pos 0, standstill, SG min/max 0/0, reads 39499, writes 14 timeouts 0
Driver 5: pos 0, standstill, SG min/max 0/0, reads 39500, writes 14 timeouts 0
Date/time: 2021-10-06 10:59:04
Slowest loop: 4.44ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 908, received 1638, lost 0, longest wait 1ms for reply type 6041, peak Tx sync delay 5, free buffers 49 (min 48), ts 507/506/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 7.37ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0

                Reply from arp on the laptop connected to the Duet 3

                PS C:\WINDOWS\system32> arp -a 192.168.1.12

Interface: 192.168.1.2 --- 0x5
  Internet Address      Physical Address      Type
  192.168.1.12          be-62-3b-3a-53-32     dynamic

                Then changing the MAC using M540

                M540
MAC: be:62:3b:3a:53:34

M540 Pbe:62:3b:3a:53:34

                The mac address is reported as changed

                M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0beta4+1 (2021-10-04 17:49:00) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956L2-G43S8-6JKD0-3S46T-9U2YF
Used output buffers: 3 of 40 (27 max)
=== RTOS ===
Static ram: 151104
Dynamic ram: 97260 of which 12 recycled
Never used RAM 102296, free system stack 200 words
Tasks: NETWORK(ready,26.4%,249) ETHERNET(notifyWait,0.1%,173) HEAT(notifyWait,0.0%,273) Move(notifyWait,0.0%,351) CanReceiv(notifyWait,0.0%,797) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,339) TMC(notifyWait,8.8%,92) MAIN(running,64.6%,943) IDLE(ready,0.0%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:04:26 ago, cause: software
Last software reset at 2021-10-06 10:57, reason: User, GCodes spinning, available RAM 102296, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 129
MCU temperature: min 36.3, current 36.5, max 36.7
Supply voltage: min 23.7, current 23.8, max 23.8, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: pos 0, standstill, SG min/max n/a, reads 60751, writes 0 timeouts 0
Driver 1: pos 0, standstill, SG min/max n/a, reads 60752, writes 0 timeouts 0
Driver 2: pos 0, standstill, SG min/max n/a, reads 60752, writes 0 timeouts 0
Driver 3: pos 0, standstill, SG min/max n/a, reads 60752, writes 0 timeouts 0
Driver 4: pos 0, standstill, SG min/max n/a, reads 60752, writes 0 timeouts 0
Driver 5: pos 0, standstill, SG min/max n/a, reads 60751, writes 0 timeouts 0
Date/time: 2021-10-06 11:01:49
Slowest loop: 4.51ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 1484, received 2640, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 6, free buffers 49 (min 49), ts 825/825/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 2.55ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0

                However its not reported as changed using arp (I tested deleting the entry first incase it was a refresh issue)

                PS C:\WINDOWS\system32> arp -d 192.168.1.12
PS C:\WINDOWS\system32> arp -a 192.168.1.12

Interface: 192.168.1.2 --- 0x5
  Internet Address      Physical Address      Type
  192.168.1.12          be-62-3b-3a-53-32     dynamic

                www.duet3d.com

                1 Reply Last reply Reply Quote 0
                • sergioundefined
                  sergio @dc42
                  last edited by sergio

                  @dc42

                  @t3p3tony can confirm on his test base, I guess it could be a firmware issue?
                  I will try to go down to 3.2 for the machine that is in conflict, since it is not very happy in the network.

                  M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0beta4 (2021-09-27 11:31:18) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956L2-G43S8-6J9D0-3SJ6L-9A0GG
Used output buffers: 1 of 40 (33 max)
=== RTOS ===
Static ram: 151080
Dynamic ram: 93860 of which 0 recycled
Never used RAM 105732, free system stack 206 words
Tasks: NETWORK(ready,29.8%,225) ETHERNET(notifyWait,0.1%,170) HEAT(notifyWait,0.0%,321) Move(notifyWait,0.0%,351) CanReceiv(notifyWait,0.0%,906) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,339) TMC(notifyWait,8.2%,92) MAIN(running,61.9%,1113) IDLE(ready,0.0%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:59:19 ago, cause: software
Last software reset at 2021-10-06 11:29, reason: User, GCodes spinning, available RAM 105732, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 133
MCU temperature: min 32.8, current 34.1, max 34.2
Supply voltage: min 27.6, current 27.9, max 28.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: pos 0, standstill, SG min/max 0/0, reads 54487, writes 17 timeouts 0
Driver 1: pos 0, standstill, SG min/max 0/0, reads 54487, writes 17 timeouts 0
Driver 2: pos 0, standstill, SG min/max 0/0, reads 54487, writes 17 timeouts 0
Driver 3: pos 0, standstill, SG min/max 0/0, reads 54487, writes 17 timeouts 0
Driver 4: pos 0, standstill, SG min/max 0/0, reads 54494, writes 11 timeouts 0
Driver 5: pos 0, standstill, SG min/max 0/0, reads 54488, writes 17 timeouts 0
Date/time: 2021-10-06 12:28:42
Slowest loop: 6.31ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.6ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 2 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 32045, received 13, lost 0, longest wait 1ms for reply type 6018, peak Tx sync delay 6, free buffers 49 (min 48), ts 17796/17795/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 10.23ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 4 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 5 2 2 2 2 0 0
                  T3P3Tonyundefined dc42undefined 2 Replies Last reply Reply Quote 0
                  • T3P3Tonyundefined
                    T3P3Tony administrators @sergio
                    last edited by

                    @sergio if 3.2 resolves the issue that would be helpful to know.

                    www.duet3d.com

                    sergioundefined 1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators @sergio
                      last edited by dc42

                      @sergio what I need is the M122 reports from both duets that are being given the same MAC address.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      sergioundefined 2 Replies Last reply Reply Quote 0
                      • sergioundefined
                        sergio @dc42
                        last edited by

                        @dc42
                        Sorry, I was asking someone to turn off that machine in that factory. I cannot access both remotely through the VPN so I needed remote hands to help me.

                        m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3RC1 (2021-05-01 09:12:50) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956L2-G43S8-6J9D0-3SJ6Q-9A0YG
Used output buffers: 3 of 40 (15 max)
=== RTOS ===
Static ram: 150680
Dynamic ram: 90564 of which 516 recycled
Never used RAM 109576, free system stack 154 words
Tasks: NETWORK(ready,31.5%,226) ETHERNET(notifyWait,1.7%,112) HEAT(delaying,0.2%,295) Move(notifyWait,0.4%,268) CanReceiv(notifyWait,0.0%,945) CanSender(notifyWait,0.0%,359) CanClock(delaying,0.1%,335) TMC(notifyWait,96.6%,93) MAIN(running,93.5%,1114) IDLE(ready,0.0%,29), total 224.0%
Owned mutexes:
=== Platform ===
Last reset 17:11:23 ago, cause: software
Last software reset time unknown, reason: User, GCodes spinning, available RAM 109576, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
Step timer max interval 224
MCU temperature: min 39.2, current 41.6, max 44.2
Supply voltage: min 23.9, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/8/0, gc cycles 0
Driver 0: position 46840, standstill, reads 18330, writes 19 timeouts 0, SG min/max 0/194
Driver 1: position 46831, standstill, reads 18330, writes 19 timeouts 0, SG min/max 0/174
Driver 2: position 46839, standstill, reads 18330, writes 19 timeouts 0, SG min/max 0/190
Driver 3: position 0, standstill, reads 18336, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 18336, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 18339, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2021-10-06 11:47:54
Slowest loop: 6.42ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.6ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 146ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5, completed moves 5, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 556955, send timeouts 556952, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 49 (min 49)
Last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 6.08ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 2 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 5 2 2 2 2 0 0
                        1 Reply Last reply Reply Quote 0
                        • sergioundefined
                          sergio @dc42
                          last edited by

                          @dc42

                          None of my Duet3 change MAC address.
                          Here is another example:

                          ; CONFIGURACION GENERAL
G90                            ; Establecer coordenadas absolutas 
M83                            ; Establecer movimientos del motor relativos
M550 P"AM_204"             ; Nombre de la máquina (Afecta a la interfaz, no se si también a su identidad en la red)

;Configuración de RED
; M540 P0xB1:0xEF:0xD0:0xAD:0xDD:0xFD ; This format doesn't work anymore
M540 PB1:EF:D0:AD:DD:FD

M552 P192.168.102.104            ; Activar comunicación por red, con IP local 1.130 
M554 P192.168.0.1            ; Puerta de enlac
M553 P255.255.0.0              ; Mascara de red
M586 P0 S1                     ; Activa protocolo HTTP
M586 P1 S1                     ; Desactiva protocolo FTP
M586 P2 S0                     ; Desactiva TELNET

M552 S1

                          b1e1a4ec-5ab4-4ebe-b4ae-c9602638e89d-image.png

                          Reported by the duet:

                          M540
MAC: b1:ef:d0:ad:dd:fd

                          Arping returns [BE:62:39:3B:53:31]

                          $ arping -c 1000 192.168.102.104 -I ens3
ARPING 192.168.102.104 from 192.168.102.1 ens3
Unicast reply from 192.168.102.104 [BE:62:39:3B:53:31]  0.802ms

                          M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3beta2 running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956L2-G43S8-6J1D2-3S86S-1A32D
Used output buffers: 1 of 40 (13 max)
=== RTOS ===
Static ram: 148476
Dynamic ram: 90516 of which 548 recycled
Never used RAM 114652, free system stack 154 words
Tasks: NETWORK(ready,234) ETHERNET(notifyWait,120) HEAT(delaying,278) CanReceiv(notifyWait,945) CanSender(notifyWait,360) CanClock(delaying,335) TMC(notifyWait,58) MAIN(running,1113) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 16:21:16 ago, cause: software
Last software reset time unknown, reason: User, GCodes spinning, available RAM 114652, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
MCU temperature: min 48.8, current 51.0, max 54.5
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 47314, standstill, reads 41408, writes 19 timeouts 0, SG min/max 0/172
Driver 1: position 47293, standstill, reads 41409, writes 19 timeouts 0, SG min/max 0/171
Driver 2: position 47328, standstill, reads 41409, writes 19 timeouts 0, SG min/max 0/160
Driver 3: position 0, standstill, reads 41414, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 41414, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 41417, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2021-10-06 11:51:00
Slowest loop: 12.65ms; fastest: 0.06ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 4.4ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 51ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5, completed moves 5, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 529894, send timeouts 529891, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 49 (min 49)
Last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 12.65ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 2 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 2 0 0

                          Best.
                          Sergio

                          1 Reply Last reply Reply Quote 0
                          • sergioundefined
                            sergio @T3P3Tony
                            last edited by

                            @t3p3tony
                            3.2 doesn't resolve the issue.

                            1 Reply Last reply Reply Quote 0
                            • dc42undefined
                              dc42 administrators
                              last edited by

                              @sergio I confirm that there are two bugs:

                              1. M540 does not set the MAC address in the Ethernet driver;
                              2. When constructing a default MAC address, the last byte of the processor unique ID is not used. This means that multiple Duet 3 boards from the same manufacturing batch may have the same default MAC address.

                              #2 is quick to fix so the fix will be in 3.4.0beta5, which we hope to release later today. #1 may take a little longer.

                              Duet WiFi hardware designer and firmware engineer
                              Please do not ask me for Duet support via PM or email, use the forum
                              http://www.escher3d.com, https://miscsolutions.wordpress.com

                              sergioundefined 2 Replies Last reply Reply Quote 0
                              • sergioundefined
                                sergio @dc42
                                last edited by

                                @dc42 Thanks a lot.

                                1 Reply Last reply Reply Quote 0
                                • sergioundefined
                                  sergio @dc42
                                  last edited by

                                  @dc42
                                  If you are looking into that code. The hex format also doesn't seem to work anymore, not sure if you are removing backwards compatibility, but if that is the case a note would be good on the M540 description.

                                  M540 P0xB1:0xEF:0xD0:0xAD:0xDD:0xFD ; This format doesn't work anymore
M540 PB1:EF:D0:AD:DD:FD

                                  Thanks a lot for the fast response.
                                  Sergio

                                  dc42undefined T3P3Tonyundefined 2 Replies Last reply Reply Quote 0
                                  • dc42undefined
                                    dc42 administrators @sergio
                                    last edited by

                                    @sergio yes that hex format has been removed. The M540 example doesn't use it, see https://duet3d.dozuki.com/Wiki/M540.

                                    Duet WiFi hardware designer and firmware engineer
                                    Please do not ask me for Duet support via PM or email, use the forum
                                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                                    1 Reply Last reply Reply Quote 0
                                    • T3P3Tonyundefined
                                      T3P3Tony administrators @sergio
                                      last edited by

                                      @sergio the default MAC address clash problem should be fixed in 3.4b5:
                                      https://github.com/Duet3D/RepRapFirmware/wiki/Changelog-RRF-3.x-Beta-&-RC#reprapfirmware-340beta5

                                      https://github.com/Duet3D/RepRapFirmware/releases/tag/3.4.0beta5

                                      www.duet3d.com

                                      sergioundefined 1 Reply Last reply Reply Quote 0
                                      • sergioundefined
                                        sergio @T3P3Tony
                                        last edited by

                                        @t3p3tony Just updated the firmware and I can confirm that the MAC is correct. Thanks

                                        1 Reply Last reply Reply Quote 1
                                        • jay_s_ukundefined jay_s_uk referenced this topic
                                        • First post
                                          Last post
                                        Unless otherwise noted, all forum content is licensed under CC-BY-SA