Trouble with Duet 3 6HC Raspberry pi setup
-
Can you send m122 and post the results?
-
@phaedrux
m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.01-RC9 running on Duet 3 MB6HC v1.01 or later
Board ID: 08DJM-956BA-NA3TJ-6JTDL-3SS6J-9TB2VUsed output buffers: 1 of 40 (10 max)
=== RTOS ===
Static ram: 154572
Dynamic ram: 160848 of which 52 recycled
Exception stack ram used: 216
Never used ram: 77528
Tasks: NETWORK(ready,2076) HEAT(blocked,1412) CanReceiv(suspended,3824) CanSender(suspended,1484) CanClock(blocked,1432) TMC(blocked,216) MAIN(running,5036) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 14:55:08 ago, cause: software
Last software reset at 2021-05-01 19:00, reason: User, spinning module LinuxInterface, available RAM 77248 bytes (slot 1)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 48.9, current 49.4, max 50.1
Supply voltage: min 22.7, current 22.8, max 22.8, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 11.9, current 12.0, max 12.1, under voltage events: 0
Driver 0: standstill, reads 13874, writes 14 timeouts 0, SG min/max 0/0
Driver 1: standstill, reads 13877, writes 11 timeouts 0, SG min/max 0/0
Driver 2: standstill, reads 13875, writes 14 timeouts 0, SG min/max 0/0
Driver 3: standstill, reads 13875, writes 14 timeouts 0, SG min/max 0/0
Driver 4: standstill, reads 13876, writes 14 timeouts 0, SG min/max 0/0
Driver 5: standstill, reads 13876, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2021-05-02 09:56:24
Slowest loop: 3.56ms; fastest: 0.14ms
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1.47ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 0, longest wait 0ms for type 0
=== Linux interface ===
State: 0, failed transfers: 1
Last transfer: 14ms ago
RX/TX seq numbers: 41738/41739
SPI underruns 1, overruns 1
Number of disconnects: 0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.2.2
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 39.81
Maximum length of RX/TX data transfers: 3088/724
- Ethernet -
-
@phaedrux I fixed the low voltage issue, the power from the duet is not enough, but it did not fix the looping problem.
-
@amostol You do have a very old firmware installed on the MB6HC, please upgrade it once via bossa before you try anything else: https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_All_other_Duet_boards
-
@chrishamm Ok thanks, I'll try that. Just one question, how can you tell? This can get very confusing, the is the OS for the pi, the DWC software, the printer/cnc files (like the config), and the firmware itself, it all seems a little overwhelming.
-
@amostol Well the pi runs a linux OS, so it gets updated pretty easily with sudo apt update and sudo apt upgrade. Once your duet firmware is up to date that command will also update all of the Duet stuff as well. So when it's working, it's actually pretty simple.
-
@amostol It is part of the
M122response:RepRapFirmware for Duet 3 MB6HC version 3.01-RC9 running on Duet 3 MB6HC v1.01 or later
The latest stable version is 3.2.2 (also installed on your Pi, see the end of that response).
-
@chrishamm I tried updating via Bossa, however, I can't get my pc or pi to recognize the duet. I have erased the firmware on the duet with the erase pins. I even followed the instruction on this page https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7 to the best of my ability, but nothing seems to work. Most of the instructions on the duet website absolutely suck, they are very short and leave many questions unanswered. Such as does the duet need a sd card in the sd card slot when doing the firmware upgrade?
-
@amostol said in Trouble with Duet 3 6HC Raspberry pi setup:
Such as does the duet need a sd card in the sd card slot when doing the firmware upgrade?
Not when doing it via USB and Bossa.
Does your USB cable handle data and power?
Does the PC make a chime when you connect the device?
Do the power LEDs on the board light up?
Did you remove the erase jumper from the pins?
-
@phaedrux Yea my problem was the USb cable I was using, apparently it was power only, I tried a thicker one and it worked, from my pc at least. I also tried it from the pi, but it keeps saying it could not communicate with the duet, at least it recognized it this time. So I just used my pc and now everything works fine, no more of that looping.
Thank you very much, I really appreciate you taking the time to help me.
