Duet3 6CH + 3CH expansion board - Missing steps.

dc42

I've put new Duet 3 MB6HC firmware in https://www.dropbox.com/sh/wme9k0z86sytg33/AAAT6wrHp2eeJHK-dYoW1Um4a?dl=0. I expect it to work well with the EXP3HC firmware already there. I am testing with newer EXP3HC firmware, but it is still somewhat experimental.

evomotors

@dc42 said in Duet3 6CH + 3CH expansion board - Missing steps.:

I've put new Duet 3 MB6HC firmware in https://www.dropbox.com/sh/wme9k0z86sytg33/AAAT6wrHp2eeJHK-dYoW1Um4a?dl=0. I expect it to work well with the EXP3HC firmware already there. I am testing with newer EXP3HC firmware, but it is still somewhat experimental.

I started the test print with the early 3.3beta that you are posted last week and DAA disabled. Then I will upgrade to the new 6CH and try again.

evomotors

@dc42 Is it possible that pressure advance has the same issue on expansion and tool boards?

dc42

@evomotors said in Duet3 6CH + 3CH expansion board - Missing steps.:

@dc42 Is it possible that pressure advance has the same issue on expansion and tool boards?

It's not pressure advance that triggers the problem I found today, it's DAA. Pressure advance will not trigger it. I ran the section of your test file that I have been using to replicate the problem with pressure advance enabled.

evomotors

@dc42 said in Duet3 6CH + 3CH expansion board - Missing steps.:

@evomotors said in Duet3 6CH + 3CH expansion board - Missing steps.:

@dc42 Is it possible that pressure advance has the same issue on expansion and tool boards?

It's not pressure advance that triggers the problem I found today, it's DAA. Pressure advance will not trigger it. I ran the section of your test file that I have been using to replicate the problem with pressure advance enabled.

I can confirm that stuttering XY moves are gone with M593 disabled. No more layer shifts. I will still complete the print to see if issue with extrusions irregularity is gone as well.

dc42

@evomotors, thanks for your preliminary results.

I've now put the latest expansion and tool boards firmwares in that folder at https://www.dropbox.com/sh/wme9k0z86sytg33/AAAT6wrHp2eeJHK-dYoW1Um4a?dl=0. The older versions are in the "Previous-16-Jan-21" subfolder.

T3P3Tony

@evomotors Testing with your config with DAA enabled is not showing any errors on the bench setup. did you get a chance to test it on the printer?

evomotors

@T3P3Tony said in Duet3 6CH + 3CH expansion board - Missing steps.:

@evomotors Testing with your config with DAA enabled is not showing any errors on the bench setup. did you get a chance to test it on the printer?

I didn't update to latest that @dc42 uploaded. But on pervious early 3.3 betta issue stops only when DAA is disabled. And yes I'm testing life on the printer.

I will upgrade to fresh build little late today.

evomotors

@dc42 @T3P3Tony The issue is fixed in the last 3.3 build! Tested with DAA enabled and print looks great (didn't look into the diagnostic messages) . Thank you!

Do you want me to mark this as answered?

deckingman

@evomotors said in Duet3 6CH + 3CH expansion board - Missing steps.:

@dc42 @T3P3Tony The issue is fixed in the last 3.3 build! Tested with DAA enabled and print looks great (didn't look into the diagnostic messages) . Thank you!

Do you want me to mark this as answered?

I'm pleased for you that your issues have been resolved. For myself, I've given up and "mothballed" my printer.

Maybe I'll pick it up again in 6 months or so but I've been battling firmware issues and coming up with "work arounds" since July 2019 and still have problems that need more work arounds. I've had enough...........