Duet2 WiFi Firmware on Raise 3d E2 ?

Proschi3D

the main problem now is that the printer doesn't start anymore.
by start I mean that the display no longer starts up in the menu.
it doesn't finish loading

jay_s_uk

@Proschi78 i guess you need to go back to 2.02 then

Proschi3D

@jay_s_uk that's exactly what I tried.
it just didn't work out.
the board stays at 3.0

Veti

@Proschi78
that might be a price to pay for running the original firmware on the raise 3d

Proschi3D

@Veti but unfortunately he no longer plays the original firmware on the board via the printer

Veti

not sure what you mean

Proschi3D

@Veti https://support.raise3d.com/E2/how-to-update-the-motion-controller-firmware-20-1143.html

The printer does not do the firmware update because the board is flashed to 3.0

Veti

@Proschi78

yes but the firmware updated to 3.0. that is what you wanted to do in the first place.
a lcd screen is not necessary for the operation of a duet.

Proschi3D

@Veti said in Duet2 WiFi Firmware on Raise 3d E2 ?:

yes but the firmware updated to 3.0. that is what you wanted to do in the first place.
a lcd screen is not necessary for the operation of a duet.

in my case it does
the WiFi module sits on the display controller

Veti

@Proschi78 said in Duet2 WiFi Firmware on Raise 3d E2 ?:

in my case it does
the WiFi module sits on the display controller

well you might want to change the eol and line settings in yat so that you can see the actual status of the wifi module.

Proschi3D

i can only connect the motion board via usb.
the display controller is also operated via this interface

Veti

@Proschi78 said in Duet2 WiFi Firmware on Raise 3d E2 ?:

the display controller is also operated via this interface

they can easily just route the spi lines to the display.

that is why the full M122 output is relevant.
you probably did not update the wifi firmware when you updated to the rrf3 firmware.

Proschi3D

@Veti said in Duet2 WiFi Firmware on Raise 3d E2 ?:

they can easily just route the spi lines to the display.
that is why the full M122 output is relevant.
you probably did not update the wifi firmware when you updated to the rrf3 firmware.

I cannot update the WiFi firmware.
because the wifi module is on a different board.
and I have no access to it via the pc

Veti

the wifi firmware is not updated via the pc.

see
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Updating_WiFi_firmware

but the M122 output is important

dc42

@Veti said in Duet2 WiFi Firmware on Raise 3d E2 ?:

@jay_s_uk said in Duet2 WiFi Firmware on Raise 3d E2 ?:

iap4e.bin

did you rename it to Duet2combinesIAP.bin like the error message says?

Duet2CombinedIAP is not the same as iap4e.bin! Renaming it will not work. You can get Duet2CombinedIAP.bin from one of the RRF 3.x releases.

Proschi3D

@dc42 can I go back from V3.0 to V2.02 that easily?

jay_s_uk

@Proschi78 that'll be why the downgrade didn't work then.
use the IAP file dc42 linked to and the firmware from my google drive

Proschi3D

@jay_s_uk ok i will try today at noon

Proschi3D

Hello everyone here who helped me. I was able to successfully install a version that was before 2.02. Then the printer could be updated via the Raise software. The whole thing was worth it for me, because now I have the possibility to control it via octoprint for whatever reason. thank you again

Proschi3D

Do you think an original duet2 Wifi would work with the hardware components?