1.19beta7 and WiFi connect

juniormajpr

WifiServer beta8 and RRF beta8. see below:

[[language]]
M122
=== Diagnostics ===
Used output buffers: 1 of 32 (1 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19beta8 running on Duet WiFi 1.0
Board ID: xxxx
Static ram used: 20900
Dynamic ram used: 96084
Recycled dynamic ram: 1800
Stack ram used: 3960 current, 4784 maximum
Never used ram: 7504
Last reset 00:00:47 ago, cause: power up
Last software reset reason: User, spinning module GCodes, available RAM 7180 bytes (slot 2)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min -210.4, current 41.4, max 41.5
Supply voltage: min 0.1, current 0.5, max 0.8, under voltage events: 0, over voltage events: 0
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.001695; fastest: 0.000027
=== Move ===
MaxReps: 0, StepErrors: 0, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
Probe change coordinates:
=== Heat ===
Bed heater = 0, chamber heater = -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is idle
WiFi firmware version 1.19beta8
WiFi MAC address aa:bb:cc:dd:ee:ff
WiFi Vcc 3.10, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 41104
HTTP sessions: 0 of 8
Socket states:  0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
ok

dc42

OK, I found the bug, it's purely a reporting issue. If you have no remembered networks but you have specified an access point name, then when you list remembered networks it prints the access point name. After you have added a remembered network, you can still retrieve the own access point name by sending M589. The fix will be in the next beta.

I still haven't worked out why it's trying to connect to an empty SSID. I'll look at that later today.

juniormajpr

@dc42: as per definition the passphrase within the AP mode hast to be at least 8 chars long, i think it would be reasonable to check for valid M589 input (i think ssid min 0 max 32 chars and passphrase min 8-64 chars).
try:

[[language]]
M552 S0
ok
WiFi module started

M589 S"test" P"test" I192.168.1.1
ok
M552 S2
ok
WiFi module started
WiFi reported error: Failed to start access point
Wifi module is idle

M589 S"test" P"testtest" I192.168.1.1
ok
M552 S2
ok
Wifi module is providing access point test, IP address 192.168.1.1

dc42

Thanks for the suggestion, I'll implement it in the next beta.

I can't reproduce the problem with failing to connect and not displaying the SSID name, but I've built a new DuetWiFiServer.bin with some changes that may help and put it at https://dl.dropboxusercontent.com/u/19369680/DuetWiFiServer.bin. Please try it.

juniormajpr

will give it a try. will give feedback tomorrow.
is there the possibility to erase the ESP (incl. flash) completly from SAM/RRF? or only via ISP?

juniormajpr

@dc: i think i found the reason, why an empty config was read…

SocketServer.cpp - row 64

[[language]]
for (size_t i = 1; i <= MaxRememberedNetworks; ++i)

shouldn't it be```
[[language]]
for (size_t i = 0; i <= MaxRememberedNetworks; ++i)

same in row 83

or better (i think) not to waste one slot at the beginning (row 64, 83, 112, 521,…)

[[language]]
for (size_t i = 0; i < MaxRememberedNetworks; i++)

dc42

The first entry is the configuration for the WiFi module as an access point. So the count starts from 1 when it is searching for a remembered SSID.

juniormajpr

hmmm… once again:

[[language]]
for (int8_t i = 0; i < num_ssids; ++i)
{
	if ((strongestNetwork < 0 || WiFi.RSSI(i) > WiFi.RSSI(strongestNetwork)) && RetrieveSsidData(WiFi.SSID(i).c_str(), ssidData))
	{
		strongestNetwork = i;
	}
}

WiFi.RSSI's and WiFi.SSID's parameters are a zero based index from prior discovered SSIDs by blocking WiFi.scanNetworks(false, true)
At this point we are looking at the wrong index. aren't we? ++i -> i++

juniormajpr

@dc: 1.19beta8+1 doesn't change the WiFi behaviour. but can you plz. confirm/check the above post?

dc42

Using ++i or i++ does exactly the same thing if the operand has primitive type and you don't use the value within the same expression, as in this case.

Zest

I just got a Duet Wifi and I'm having a hell of a time with the WIFI setup. I have tried flashing 1.18 stable as well as 1.19 beta 8. I first attempted upgrades via M997 but eventually tried the erase/reset/reload via samba. I have gotten it to connect once or twice but it seems whenever I edit config.g to uncomment M552 S1 it fails to connect again after reboot. I have fiddled with it quite a bit since then and haven't been able to get it to talk to my router again.

I've noticed a couple things

when using 1.18 M552 will say that the board is in AP mode but I can't see it in my list of WIFI networks.
when it does this it also says hostname is some bunch of gibberish ascii characters
when using 1.19 Beta 8 M587 returns the two remembered networks I have configured in my SetNetwork macro however when I do a M552 S1 I get

M587
SENDING:M587
Remembered networks:
seawest
seawest 5G
M552 S1
SENDING:M552 S1
WiFi reported error: no known networks found
Wifi module is idle

I'm starting to think the board is faulty. Is there anything else I can try? It's almost as if the WIFI module is retaining some kind of garbage. Is there a way to purge everything so I'm starting fresh? SD Card, memory, everything?

dc42

The "no known networks found" message means that it did a network scan and didn't find either of the SSIDs you configured. How strong is the signal from your router where the Duet is? Is the Duet surrounded by metalwork that would attenuate the signal?

The Duet WiFi does 2.4GHz only, and I presume seawest 5G is a 5GHz access point.

I think access point names are case sensitive. Is 'seawest' exactly how your access point name appears when you connect to it from a smartphone, tablet etc. ?

Zest

wow thanks for the quick reply. seawest is the name of my 2.4 Ghz network and my seawest 5G is my 5 Ghz network. Both are off of the same ASUS router that sits about 10 feet away. The names are case sensitive and exactly as they're seen from my iphone. My password is alphanumeric and only contains letters and a number.

The thing that makes me suspicious that the board is bad is the fact that I don't see "Duet WIFI" when the board thinks it's in AP mode when using 1.18. Are there any debug commands I can use to test the functionality of the WIFI module itself? I was able to get the board to connect a handful of times and it seemed tied to loading a new WIFI firmware. However, I have tried reloading firmware several times since then and I haven't been able to re-establish a connection.

I WAS able to connect to the "Duet WIFI" SSID but only once. When that occurred I could see my neighbor's APs as well as my own. I was also able to get into the web interface but as soon as I uncommented "M552 S1" and rebooted I had the same problems all over again and could not reconnect.

dc42

When you are using firmware 1.18 and the Duet reports that it is in AP mode, you should be able to find it in the network listing on your smartphone assuming your smartphone isn't only looking for 5GHz networks. If you can't, ask for the Duet to be replaced.

juniormajpr

@DC42: regaring the SSID/PSK topic:

within the StartClient() you are calling RetrieveSsidData() which overwrites ssidData each time it is called with data from EEPROM.
But at the end of StartClient() you are calling ConnectToAccessPoint() with the last update of ssidData as parameter (which could store wrong data at this point caused by prior RetrieveSsidData() calls).

i think RetrieveSsidData() should be called again with WiFi.SSID(strongestNetwork) as paramter right after the strongestNetwork was found to update ssidData with the correct parameters again. adopted version: https://www.dropbox.com/s/60djqiyv9f380xe/DuetWiFiServer.bin?dl=0

dc42

Thanks for spotting that. I'll update it when I am back in the office.

juniormajpr

Ps. Can also confirm that '@' within passphrase isn't a problem at all!

dc42

Thanks for the confirmation!