Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet 3 Disconnects from SBC

    Scheduled Pinned Locked Moved Unsolved
    Firmware installation
    4
    32
    1.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • mrenz999undefined
      mrenz999 @Phaedrux
      last edited by

      @Phaedrux Ok I got it updated using BOSSA through the pi. 2 failed prints later.

      m122
      === Diagnostics ===
      RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
      Board ID: 08DJM-956L2-G43S8-6J1FA-3SJ6P-1B06G
      Used output buffers: 1 of 40 (13 max)
      === RTOS ===
      Static ram: 154604
      Dynamic ram: 163364 of which 20 recycled
      Exception stack ram used: 536
      Never used ram: 74692
      Tasks: NETWORK(ready,1972) HEAT(blocked,1188) CanReceiv(suspended,3820) CanSender(suspended,1420) CanClock(blocked,1436) TMC(blocked,68) MAIN(running,2868) IDLE(ready,76)
      Owned mutexes:
      === Platform ===
      Last reset 10:16:20 ago, cause: software
      Last software reset at 2020-09-05 05:11, reason: User, spinning module LinuxInterface, available RAM 75124 bytes (slot 3)
      Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
      Error status: 0
      MCU temperature: min 40.5, current 40.8, max 43.9
      Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
      12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
      Driver 0: standstill, reads 56301, writes 8 timeouts 0, SG min/max 0/591
      Driver 1: standstill, reads 56300, writes 8 timeouts 0, SG min/max 0/646
      Driver 2: standstill, reads 56301, writes 8 timeouts 0, SG min/max 0/99
      Driver 3: standstill, reads 56300, writes 8 timeouts 0, SG min/max 0/97
      Driver 4: standstill, reads 56300, writes 8 timeouts 0, SG min/max 0/78
      Driver 5: standstill, reads 56304, writes 4 timeouts 0, SG min/max 0/847
      Date/time: 2020-09-05 15:27:29
      Slowest loop: 5.84ms; fastest: 0.15ms
      === Storage ===
      Free file entries: 10
      SD card 0 not detected, interface speed: 37.5MBytes/sec
      SD card longest read time 0.0ms, write time 0.0ms, max retries 0
      === Move ===
      Hiccups: 0(0), FreeDm: 375, MinFreeDm: 292, MaxWait: 9557402ms
      Bed compensation in use: none, comp offset 0.000
      === MainDDARing ===
      Scheduled moves: 41108, completed moves: 41108, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
      === AuxDDARing ===
      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
      === Heat ===
      Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
      === GCodes ===
      Segments left: 0
      Movement lock held by null
      HTTP* is ready with "M122" in state(s) 0
      Telnet is idle in state(s) 0
      File* is idle in state(s) 0
      USB is idle in state(s) 0
      Aux is assembling a command in state(s) 0
      Trigger* is idle in state(s) 0
      Queue* is idle in state(s) 0
      LCD is idle in state(s) 0
      SBC is idle in state(s) 0
      Daemon* is idle in state(s) 0 0, running macro
      Aux2 is idle in state(s) 0
      Autopause is idle in state(s) 0
      Code queue is empty.
      === Network ===
      Slowest loop: 2.13ms; fastest: 0.01ms
      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
      HTTP sessions: 0 of 8

      • Ethernet -
        State: disabled
        Error counts: 0 0 0 0 0
        Socket states: 0 0 0 0 0 0 0 0
        === CAN ===
        Messages sent 91415, longest wait 0ms for type 0
        === Linux interface ===
        State: 0, failed transfers: 309
        Last transfer: 16ms ago
        RX/TX seq numbers: 20337/20313
        SPI underruns 118, overruns 118
        Number of disconnects: 0
        Buffer RX/TX: 0/0-0
        === Duet Control Server ===
        Duet Control Server v3.1.1
        Code buffer space: 4096
        Configured SPI speed: 8000000 Hz
        Full transfers per second: 32.45
      1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator
        last edited by

        Does it fail on every print now?

        Can you share the gcode file you're printing?

        Can you setup debugging info?

        https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Monitoring_optional

        Z-Bot CoreXY Build | Thingiverse Profile

        mrenz999undefined 3 Replies Last reply Reply Quote 0
        • mrenz999undefined
          mrenz999 @Phaedrux
          last edited by

          @Phaedrux Yes every print. I have tried mulitple prints. I will setup debugging and share the Gcode this evening when I get back from work. Every print it just stops about 10% or so in. It has rebooted but on the status page it says it has completed the print.

          1 Reply Last reply Reply Quote 0
          • mrenz999undefined
            mrenz999 @Phaedrux
            last edited by mrenz999

            @Phaedrux
            Where can I upload the file I was printing ?
            m122
            === Diagnostics ===
            RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
            Board ID: 08DJM-956L2-G43S8-6J1FA-3SJ6P-1B06G
            Used output buffers: 1 of 40 (10 max)
            === RTOS ===
            Static ram: 154604
            Dynamic ram: 163156 of which 20 recycled
            Exception stack ram used: 528
            Never used ram: 74908
            Tasks: NETWORK(ready,1972) HEAT(blocked,1188) CanReceiv(suspended,3820) CanSender(suspended,1420) CanClock(blocked,1436) TMC(blocked,68) MAIN(running,2672) IDLE(ready,76)
            Owned mutexes:
            === Platform ===
            Last reset 00:28:11 ago, cause: power up
            Last software reset at 2020-09-05 17:15, reason: User, spinning module LinuxInterface, available RAM 74692 bytes (slot 0)
            Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
            Error status: 0
            MCU temperature: min 36.1, current 41.6, max 41.7
            Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
            12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
            Driver 0: standstill, reads 53593, writes 17 timeouts 0, SG min/max 0/216
            Driver 1: standstill, reads 53594, writes 17 timeouts 0, SG min/max 0/165
            Driver 2: standstill, reads 53594, writes 17 timeouts 0, SG min/max 0/104
            Driver 3: standstill, reads 53594, writes 17 timeouts 0, SG min/max 0/98
            Driver 4: standstill, reads 53595, writes 17 timeouts 0, SG min/max 0/103
            Driver 5: standstill, reads 53595, writes 17 timeouts 0, SG min/max 0/210
            Date/time: 2020-09-06 03:21:15
            Slowest loop: 5.23ms; fastest: 0.14ms
            === Storage ===
            Free file entries: 10
            SD card 0 not detected, interface speed: 37.5MBytes/sec
            SD card longest read time 0.0ms, write time 0.0ms, max retries 0
            === Move ===
            Hiccups: 0(0), FreeDm: 375, MinFreeDm: 340, MaxWait: 1539522ms
            Bed compensation in use: none, comp offset 0.000
            === MainDDARing ===
            Scheduled moves: 1396, completed moves: 1396, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
            === AuxDDARing ===
            Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
            === Heat ===
            Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
            === GCodes ===
            Segments left: 0
            Movement lock held by null
            HTTP* is ready with "M122" in state(s) 0
            Telnet is idle in state(s) 0
            File* is idle in state(s) 0
            USB is idle in state(s) 0
            Aux is assembling a command in state(s) 0
            Trigger* is idle in state(s) 0
            Queue* is idle in state(s) 0
            LCD is idle in state(s) 0
            SBC is idle in state(s) 0
            Daemon* is idle in state(s) 0
            Aux2 is idle in state(s) 0
            Autopause is idle in state(s) 0
            Code queue is empty.
            === Network ===
            Slowest loop: 2.14ms; fastest: 0.01ms
            Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
            HTTP sessions: 0 of 8

            • Ethernet -
              State: disabled
              Error counts: 0 0 0 0 0
              Socket states: 0 0 0 0 0 0 0 0
              === CAN ===
              Messages sent 6679, longest wait 0ms for type 0
              === Linux interface ===
              State: 0, failed transfers: 2
              Last transfer: 22ms ago
              RX/TX seq numbers: 54222/54222
              SPI underruns 3, overruns 3
              Number of disconnects: 0
              Buffer RX/TX: 0/0-0
              === Duet Control Server ===
              Duet Control Server v3.1.1
              Code buffer space: 4096
              Configured SPI speed: 8000000 Hz
              Full transfers per second: 14.09
            Phaedruxundefined 1 Reply Last reply Reply Quote 0
            • mrenz999undefined
              mrenz999 @Phaedrux
              last edited by

              @Phaedrux
              Duet Control Server v3.1.1
              Written by Christian Hammacher for Duet3D
              Licensed under the terms of the GNU Public License Version 3

              [info] Settings loaded
              [info] Environment initialized
              [fatal] Could not connect to Duet (Board is not available (no header))
              [debug] System.OperationCanceledException: Board is not available (no header)
              at DuetControlServer.SPI.DataTransfer.ExchangeHeader() in /home/christian/Duet3D/DuetSoftwareFramework/src/DuetControlServer/SPI/DataTransfer.cs:line 1093
              at DuetControlServer.SPI.DataTransfer.PerformFullTransfer(Boolean connecting) in /home/christian/Duet3D/DuetSoftwareFramework/src/DuetControlServer/SPI/DataTransfer.cs:line 162
              at DuetControlServer.SPI.DataTransfer.Init() in /home/christian/Duet3D/DuetSoftwareFramework/src/DuetControlServer/SPI/DataTransfer.cs:line 102
              at DuetControlServer.Program.Main(String[] args) in /home/christian/Duet3D/DuetSoftwareFramework/src/DuetControlServer/Program.cs:line 10

              This is what i get when I try to run debug

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator @mrenz999
                last edited by

                @mrenz999 said in Duet 3 Disconnects from SBC:

                Where can I upload the file I was printing ?

                If it's small enough you can upload it here. If it's too large try zipping it and use dropbox or something like that to share it.

                Z-Bot CoreXY Build | Thingiverse Profile

                mrenz999undefined 1 Reply Last reply Reply Quote 0
                • mrenz999undefined
                  mrenz999 @Phaedrux
                  last edited by mrenz999

                  @Phaedrux
                  https://www.dropbox.com/s/c1a8ve3eq0kahxr/CFFFP_lotus_nightlight.gcode?dl=0
                  Constant G28 network errors pop up.

                  Phaedruxundefined 1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator @mrenz999
                    last edited by

                    @mrenz999 said in Duet 3 Disconnects from SBC:

                    Constant G28 network errors pop up.

                    What does this mean?

                    Z-Bot CoreXY Build | Thingiverse Profile

                    mrenz999undefined 1 Reply Last reply Reply Quote 0
                    • mrenz999undefined
                      mrenz999 @Phaedrux
                      last edited by

                      @Phaedrux It means everything I do pops that up on the bottom right of the screen. However, I completely redid the SBC and this morning everything seems to be working.

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        It says G28 network error?

                        Well glad to hear that it seems to be working now.

                        Z-Bot CoreXY Build | Thingiverse Profile

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA