Cambio elettronica
-
Good afternoon everybody.
After two years of absence and inactivity I decided to return.
Some time ago I purchased the X5SA PRO printer from Tronxy which mounts a 24v electronic "CXY-V8-190729" with self leveling.
The mechanics is a Corexy with industrial linear guides.
The Firmware is of the chitu adapted to the tronxy and therefore cannot be modified.
Four days ago the electronics got stuck in the sense that it no longer accepted the commands, so I decided
to change the card with the duet2 wifi that I already had and mounted on another Cartesian printer with plastic frame "I3 Pro B from geeetech"
Since the original i3 pro b printer was 12v then added a 24v power supply and mounted the duet2 wifi card.
After looking and looking at the wiring, I decided to change the card, so far so good.
Yesterday I turn on the printer with the new card, fantastic it turned on without any problem
Now there are the configuration problems, having read several treed translated into Italian "I don't know English
" and with various confusion because it is not that the translation makes it clear what the interlocutor writes. So I decided to join here and help out all of you as best I can by describing what I did and how I did it.Let's start with order:
Firmware to be updated
controlweb to update
Z probe model (XY-08N NPN NO - DC6-36v 3 wires + / - / S)
Point 1: I updated the firmware from 2.05 to version 3 but it was not successful, that is, after updating it it always gave me the FW 2.05 so from webcontrol I deleted the FW 2.05 from the SD card and reinstalled the 3.0 now works, here of then I put the log.
console.txtPoint 2: no problem here, I uploaded via webcontrol in "system / upload system files" once uploaded the file asks you to reset everything, gives the ok and everything is done.
As for point 1, someone found problems with the "2000 C" off-scale temperatures, I also had the same problem but solved it as described in point 1.
Step 3: how to connect the probe z of the tronxy, I connected the positive and negative to the output of the fan always running having 24v as power supply therefore also the fans work at 24v, the signal cable I connected it with a diode to the Z_Probe_in, with a tester I checked the output voltage of the probe that gave me 0.650 v in active mode, so it seems to work well (BEWARE of the voltage being at 24v also the sensor output will have 24 but having put a diode will have 'a voltage drop when active, the sensor in question detects aluminum, iron, steel, but NOT glass.
I hope I have been of help to all those who have purchased a tronxy x5sa pro and want to change electronics, I also hope to be in the right tread.
-
-
@Danal said in Cambio elettronica:
@Leblond Grazie!
Questo è molto utile
Per favore, contribuisci di più, in qualsiasi momento.
ti ringario faro' il possibile
-
@Leblond Thanks for your report!
Ian
-
Ragazzi una domanda, dato che devo vedere se i motori girino nel verso giusto mi chiedevo se esisteva un modo per bypassare l'home di tutti gli assi, non vorrei che andassero a sbattere o peggio ancora rovinarmi il piatto di stampa.
-
@Leblond Send
M564 S0 H0to allow moves without homing, and outside the limits of the print volume.Ian
-
@droftarts grazie
-
@droftarts said in Cambio elettronica:
M564 S0 H0
ho lanciato il comando M564 S0 H0, poi G1 X50 F200 non funziona, quindi ho provato a mandare l'asse x in home, ma mi si e' alzato l'asse Z, forse qualcosina non quadra -
@Leblond It sounds like you have connected the stepper motors to the wrong pins! See the wiring diagram here for the motor connections: https://duet3d.dozuki.com/Wiki/Duet_Wiring_Diagrams
If your wiring is correct, post your config.g file. Also send M115 and post the response.
Ian
-
0:/sys/config.g.bak
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 13:40:08 GMT+0200 (Ora legale dell’Europa centrale); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"X5SA PRO" ; set printer nameM667 S1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X330 Y330 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Z-Probe
M558 P1 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X60:300 Y50:300 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss -
-
@Leblond said in Cambio elettronica:
M584 X0 Y1 Z2 E3
That looks okay. Note that the order of the driver pins on the board, from left to right, is E1, E0, X, Y, Z.
Ian
-
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 13:40:08 GMT+0200 (Ora legale dell’Europa centrale); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"X5SA PRO" ; set printer name;M667 S1 ; select CoreXY mode
M669 K1
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X330 Y330 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Z-Probe
M558 P5 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X60:300 Y50:300 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss -
sicuramente e' tutto sbagliato ma l'ho fatto con il configuratore reprap
-
-
l'unico problema elettrico che ho riscontrato e' il colore dei fili
2b rosso
2a blu
1a verde
1b neroma la connessione dei fili dei motori sono invertiti le fasi 1a e 1b
che sia quello? -
cioe' i cavi dei motori che dovrebbero essere 2b-R 2a-B 1a-V 1b-N sui fili 1a e 1b sono invertiti
-
G28
Error: Z probe already triggered at start of probing move -
Ragazzi ho realmente bisogno di voi, non ce ne salto fuori, mi continua a dare come errore Z probe already triggered at start of probing move
-
Non so come fargli cambiare stato
