Firmware 2.03RC5/1.24RC5 released

[boldnuts]

I rolled back to 2.02 and it does seem to converge a bit better (quicker), see screen shots from my TLM with smart effector

[dc42]

@boldnuts, did you mean that the first of the 2 images in your post is with firmware 2.02 and the second is with 2.03RC5?

@Gone2Far, if you are seeing a change in trigger sensitivity, I don't think that's anything to do with the firmware change. Delta calibration should converge after no more than 3 iterations, so if it is taking more than that then I suspect you may be getting false triggering. If you need to set sensitivity to 128 then I suspect that a fan or something else is interfering with the Smart Effector electronics.

[boldnuts]

Yes that's correct, first image is 2.02 and second is 2.03RC5

[denke]

@dc42 It did in my case, I use 24V sunon 40x40x20 fans, which are very noisy (electricly speaking)
My solution was connecting the main fan to a PWM output and stopping the fan for the duration of the delta calibration.

[dc42]

@boldnuts said in Firmware 2.03RC5/1.24RC5 released:

Yes that's correct, first image is 2.02 and second is 2.03RC5

Does the speed of convergence change depending on whether you do or don't home the printer between auto calibration runs?

[boldnuts]

I don't re home between calibrations, but I will re check this for you

[dc42]

@boldnuts said in Firmware 2.03RC5/1.24RC5 released:

I don't re home between calibrations, but I will re check this for you

I don't normally home between re-calibrations either, but it is conceivable that there could be a firmware bug that causes it to make a difference. There were small changes in RRF 2.03 to how the corrections made by auto calibration are applied. That said, I've checked that code several times and I believe it should have exactly the same effect as the 2.02 code.

[dc42]

@denke said in Firmware 2.03RC5/1.24RC5 released:

@dc42 It did in my case, I use 24V sunon 40x40x20 fans, which are very noisy (electricly speaking)
My solution was connecting the main fan to a PWM output and stopping the fan for the duration of the delta calibration.

It's actually the magnetic field from the fan(s) that causes the problem. In revision 2 of the Smart Effector we moved the heatsink fan away from the sensitive electronicas to mitigate this issue. The E3D heatsink fan doesn't cause any issues, but some other fans do.

[boldnuts]

First image is 2.03RC5, homing between calibration which does seem better than before and 2nd image 2.02 with the same settings

[dc42]

Thanks. Please can you try 2.03 without homing between calibration runs a few times, to see whether it is consistently worse.

[boldnuts]

2.03 it's not quite as consistent as 2.02, but very little in, nit picking at best, ran both 6 times with no homing, bottom image is 2.02

[dc42]

Thanks. On that basis, I think there is no significant difference between 2.02 and 2.03.

[dragonn]

I see 2.03 final on github, question - what is the "jerk policy" for?
I can not find any information about that.

[wilriker]

@dragonn said in Firmware 2.03RC5/1.24RC5 released:

I see 2.03 final on github, question - what is the "jerk policy" for?
I can not find any information about that.

It made me curious, too. I found it in the GCode documentation:

The default jerk policy is 0, which replicates the behaviour of earlier versions of RRF (jerk is only applied between two printing moves, or between two travel moves, and only if they both involve XY movement or neither does). Changing the jerk policy to 1 allows jerk to be applied between any pair of moves.

[dragonn]

@wilriker It must be recently add when I search it it wasn't there

[dc42]

@boldnuts said in Firmware 2.03RC5/1.24RC5 released:

2.03 it's not quite as consistent as 2.02, but very little in, nit picking at best, ran both 6 times with no homing, bottom image is 2.02

@boldnuts , you were right! There is a bug in the 2.03 autocalibration function. Please try the 2.03+1 binary at https://www.dropbox.com/s/zfv4p7dr2ycmjzd/Duet2CombinedFirmware.bin?dl=0 and see whether it gives you better results, as good as 2.02 did.

[boldnuts]

Calibration all sorted out now dc42, Thank you

[dc42]

Thanks for confirming this.

[jakemestre]

@dc42 I've got a delta with end stops that are shy of ultimate height movement. There's a tool changer in the dead space of the delta and this way I can easy move in XY to get new tools. Any way the "target position outside machine limits" could controlled with the M208?

[dc42]

@jakemestre said in Firmware 2.03RC5/1.24RC5 released:

@dc42 I've got a delta with end stops that are shy of ultimate height movement. There's a tool changer in the dead space of the delta and this way I can easy move in XY to get new tools. Any way the "target position outside machine limits" could controlled with the M208?

Not currently; but with care you could use G1 S2 individual motor moves to move beyond the limits.